Chauvet LED-PAR200B Bedienungsanleitung

CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A

(800) 762-1084 –(954) 929-1115

FAX (954) 929-5560

www.chauvetlighting.com

2006-07-06/10:32

LED-PAR200B

OLORsplash™200B

USER MANUAL

LED-PAR200B User Manual 2 2006-07-06/10:32

TABLE OF CONTENT

TABLE OF CONTENT....................................................................................................................................................... 2

BEFORE YOU BEGIN....................................................................................................................................................... 3

WHAT IS INCLUDED .......................................................................................................................................................................................................... 3

UNPACKING INSTRUCTIONS.............................................................................................................................................................................................. 3

AC POWER ..................................................................................................................................................................................................................... 3

SAFETY INSTRUCTIONS.................................................................................................................................................................................................... 3

INTRODUCTION............................................................................................................................................................... 4

FEATURES....................................................................................................................................................................................................................... 4

DMX CHANNEL SUMMARY ............................................................................................................................................................................................... 4

PRODUCT OVERVIEW....................................................................................................................................................................................................... 5

SETUP .............................................................................................................................................................................. 6

POWER ........................................................................................................................................................................................................................... 6

MOUNTING ...................................................................................................................................................................................................................... 6

OPERATING INSTRUCTIONS.......................................................................................................................................... 7

MASTER/SLAVE MODE..................................................................................................................................................................................................... 7

Daisy Chain Connection..................................................................................................................................................................................... 7

Dipswitch Options............................................................................................................................................................................................... 7

DMX CONTROL MODE..................................................................................................................................................................................................... 8

Setting the DMX address ................................................................................................................................................................................... 8

APPENDIX........................................................................................................................................................................ 9

DMX PRIMER .................................................................................................................................................................................................................. 9

Fixture Linking .................................................................................................................................................................................................... 9

DMX CHANNEL VALUES ................................................................................................................................................................................................ 10

RETURNS PROCEDURE .................................................................................................................................................................................................. 11

CLAIMS ......................................................................................................................................................................................................................... 11

PHOTOMETRIC............................................................................................................................................................................................................... 11

DMX DIPSWITCH QUICK REFERENCE CHART ................................................................................................................................................................. 12

TECHNICAL SPECIFICATIONS .......................................................................................................................................................................................... 13

TECHNICAL SUPPORT .................................................................................................................................................................................................... 13

LED-PAR200B User Manual 3 2006-07-06/10:32

AC Voltage Switch Example

BEFORE YOU BEGIN

What is included

1 x LED-PAR200B COLORsplash™200B

Warranty Card

Users Manual

Unpacking Instructions

Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that

all parts are present, and have been received in good condition. Notify the shipper immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture

must be returned to the factory, it is important that the fixture be returned in the original factory box

and packing.

AC Power

To determine the power requirements for a particular product, see the label affixed to the back plate

of the product or refer to the product’sspecifications chart. A product’slisted current rating is its

average current draw under normal conditions. All fixtures must be powered directly off a switched

circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit,

even if the rheostat or dimmer channel is used solely for a 0% to 100%

switch. Before applying power, check that the source voltage matches the

product’srequirement. Check the product or device carefully to make sure

that if a voltage selection switch exists that it is set to the correct line

voltage you will use.

Warning! If applicable, verify that the power select switch on your unit matches the line voltage applied.

All fixtures must be connected to circuits with a suitable Earth Ground.

Safety Instructions

Please keep this User Guide for future consultation. If you

sell the unit to another user, be sure that they also receive

this instruction booklet.

Always make sure that you are connecting to the proper

voltage and that the line voltage you are connecting to is

not higher than that stated on decal or rear panel of the

fixture.

This product is intended for indoor use only!

To prevent risk of fire or shock, do not expose fixture to

rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

The unit must be installed in a location with adequate

ventilation, at least 50cm from adjacent surfaces. Be sure

that no ventilation slots are blocked.

Always disconnect from power source before servicing or

replacing lamp or fuse and be sure to replace with same

lamp source.

Secure fixture to fastening device using a safety chain.

Never carry the fixture solely by its head. Use its carrying

handles.

Maximum ambient temperature is Ta: 40°. Do not operate

fixture at temperatures higher than this.

In the event of serious operating problem, stop using the

unit immediately. Never try to repair the unit by yourself.

Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the

same type spare parts.

Don’t connect the device to a dimmer pack.

Make sure power cord is never crimped or damaged.

Never disconnect power cord by pulling or tugging on the

cord.

Avoid direct eye exposure to lamp while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET.

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance?

LED-PAR200B User Manual 4 2006-07-06/10:32

1 2 3 4 5 6

RGB 000~029 Red

000~255 Green

000~255 Blue

000~255

Pulse 030~119

(Slow>Fast)

No Function

Strobe

000~255

Color Macros 120~149 Color Macro

000~255 No Function

RGB Chase 150~179 Chase Speed

000~255

Color Change 180~209

Color Change

w/ fade 210~239

Program Speed

000~255

Sound 240~255

No Function

No Function No Function

No Function

Dimmer

000~255

DMX CHANNEL

(COLUMNS)

CONTROL MODES & OPTIONS

(Rows)

For a detailed view of DMX values turn to the Appendix section in this manual. Control mode parameters are set by DMX

values in Channel # 1.

INTRODUCTION

Features

CONTROL FEATURES

6-channel DMX-512 LED washlight can

199 ultra bright LEDs: 67 red, 66 green, 66 blue

Built-in color change programs

FEATURES

Ultra bright LED's

RGB color mixing

Up to 100,000-hour LED life span

Master/Slave mode

Selectable colors with or without controller

RGB color mixing

OPTIONS

Programmable: Any universal DMX-512 controller

DMX Channel Summary

LED-PAR200B User Manual 5 2006-07-06/10:32

DMX dipswitches:

DMX channel addressing

DMX Connectors

Switch selectable voltage

Fuse

Blue LED Status

- Blinks continuously: DMX signal present

- Solid: Music mode

LED will blink in Auto mode to signify rate or

speed set by the Min-Max rotary button.

Hanging yoke

All LEDs evenly staggered

for optimum color

generation.

Red LED: Power Indicator

Min

Max Rotary button

Music/Auto switch

Product Overview

Introduction

LED-PAR200B User Manual 6 2006-07-06/10:32

Slide switch up or down

depending on your line voltage.

Hanging Clamp

SETUP

Power

Your product is equipped with switch-selectable AC power setting.

Warning! Verify that the power select switch on your unit

matches the line voltage applied. All fixtures must

be connected to circuits with a suitable Earth

Ground.

To determine the power requirements for a particular fixture, see the label affixed to the back plate

of the fixture or refer to the fixture’s specifications chart.

A fixture’s listed current rating is its average current draw under normal conditions.

All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat

(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0%

to 100% switch.

Before applying power to a fixture, check that the source voltage matches the fixture’s

requirement.

All fixtures must be connected to circuits with a suitable Earth Ground.

Power Cable Configuration

CABLE PIN INTERNATIONAL

BROWN Live L

BLUE Neutral N

YELLOW/GREEN Earth EG (Ground)

Mounting

Orientation

This fixture can be mounted on a truss using a clamp in any

position.

Rigging

The fixture includes a mounting yoke to which 1 rigging clamp can be bolted.

1. Align the clamp screw with the center hole on the yoke and tighten.

2. Verify the structure can hold 10 times the weight of all to-be installed fixtures.

3. Adjust the angle on the yoke arm as necessary.

LED-PAR200B User Manual 7 2006-07-06/10:32

OPERATING INSTRUCTIONS

The COLORsplash™200B is a DMX-512 controllable, full RGB color mix par can made up of highly

efficient and super bright leds. All red, green and blue LEDs can be controlled separately allowing the

creation of an unlimited range of colors.

The COLORsplash™200B can operate in Stand-Alone, Master/Slave and via DMX-512 control

utilizing 6 DMX channels.

Master/Slave Mode

The Master/Slave mode will allow you to link up to as many units you want in a daisy chain fashion. In

this mode, the first unit in the daisy chain will automatically command all other units following.

1. Connect all COLORsplash™200B units in a daisy chain fashion as described in the section

following.

2. Dipswitch settings on slave fixtures are not required and will have no affect.

3. Set all dipswitches on the Master unit to the “Off”position and the unit will run its built in color

change program.

OPTIONS

- Set Music/Auto switch to Music and for sound-activated triggering of the program

- Set Music/Auto switch to Auto then use the rotary dial to adjust speed of the program

- See below under Dipswitch Options for additional program settings

Daisy Chain Connection

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector

of the first fixture.

2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin

connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,

proceed to connect from the output as stated above to the input of the following fixture and so on.

Dipswitch Options

FUNCTIONS DIPSWITCHES (ON ) NOTES &DESCRIPTION

Color change

program None Music/Auto switch

Music: Sound Activated, Rotary knob sets sound sensitivity

Auto: Rotary knob sets speed of program

1 Low Intensity

2 Medium Intensity

Red LEDs

3 Full Intensity

4 Low Intensity

5 Medium Intensity

Green LEDs

6 Full Intensity

7 Low Intensity

8 Medium Intensity

Blue LEDs

9 Full Intensity

“User Color”Any combination of Red, Green and

Blue LED intensity to create custom

color. For example Dipswitch 9 and 3 ON creates a Pink color

Appendix

LED-PAR200B User Manual 8 2006-07-06/10:32

DMX Control Mode

Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to

customizing or creating a show. In this mode you will be able to control each individual trait of the

fixture and each fixture independently. The COLORsplash™200B uses 6 channels of control.

1. A working DMX-512 signal source plugged into the COLORsplash™200B activates the DMX

mode.

Setting the DMX address

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start

address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data

on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels

of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,

102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate

the start address selected for future reference.

If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping

to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that

will help you understand its use.

Set the start address using the group of DIP switches located usually on bottom of the fixture. Each

dip switch has an associated value. Adding the value of each switch in the ON position will provide

the start address. Determining which switches to toggle ON given a specific start address can be

accomplished in the following manner. By subtracting the largest switch value possible from the

selected start address until zero is achieved.

EXAMPLE STARTING ADDRESS

Address 10

Pin # 4 = 8

Pin # 2 = 2

Total = 10

Address 24

Pin # 5 = 16

Pin # 4 = 8

Total = 24

Resolving address using

simple math.

Address 233

233 –(128) = 105, Turn ON Dip # 8

105 –(64) = 41, Turn ON Dip # 7

41 –(32) = 9, Turn ON Dip # 6

9 –(8) = 1, Turn ON Dip # 4

1 –(1) = 0, Turn ON Dip # 1

You will most likely use the first

available number which maybe

number 1. This number was

selected for example purposes.

DIP SWITCH (DMX VALUE)

128

256

1 2 3 4 5 6 7 8 9 10

128

256

Option

1 2 3 4 5 6 7 8 9 10

128

256

Option

Appendix

LED-PAR200B User Manual 9 2006-07-06/10:32

APPENDIX

DMX Primer

There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A

fixture capable of receiving DMX-512 will require one or a number of sequential channels. The user

must assign a starting address on the fixture that indicates the first channel reserved in the controller.

There are many different types of DMX controllable fixtures and they all may vary in the total number

of channels required. Choosing a start address should be planned in advance. Channels should

never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is

set incorrectly. You can however, control multiple fixtures of the same type using the same starting

address as long as the intended result is that of unison movement or operation. In other words, the

fixtures will be slaved together and all respond exactly the same.

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is

where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which

the fixtures are connected is not important and has no effect on how a controller communicates to

each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures

using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The

shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET

carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)

Fixture Linking

Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5

pin to 3 pin adapter. CHAUVET Model No: DMX5M.

The chart below details a proper cable conversion:

3PIN TO 5PIN CONVERSION CHART

Conductor 3 Pin Female (output) 5 Pin Male (Input)

Ground/Shield Pin 1 Pin 1

Data ( - )signal Pin 2 Pin 2

Data ( + ) signal Pin 3 Pin 3

Do not use Do not use

COMMON

DMX +

DMX

INPUT

OUTPUT

Resistance 120

ohm 1/4w between

pin 2 (DMX -) and

pin 3 (DMX +) of

the last fixture.

Termination reduces signal errors and to

avoid signal transmission problems and

interference, it is always advisable to

connect a DMX signal terminator.

DMX connector configuration

Appendix

LED-PAR200B User Manual 10 2006-07-06/10:32

DMX Channel Values

NOTE!

Please read all instructions carefully on fixture DMX control mode and addressing.

DMX channels 2, 3, 4, 5 and 6 functions are determined by the current settings of channel 1. For

example, while Channel 1 is set between 000 and 029 the following conditions will apply;

Channel 2 will control the Red LEDs

Channel 3 will control the Green LEDs

Channel 4 will control the Blue LEDs

Channel 5 will control Strobing

Channel 6 will control the Dimmer

CHANNEL VALUE FUNCTION CH 2 CH 3 CH 4 CH 5 CH 6

000 029

RGB Control Mode Red

000 255 Green

000 255 Blue

000 255 Strobe

000 255

030 059

060 119

Pulse Strobe

Pulse ( 0 <-> 100% )

Pulse ( 100 <-> 0% )

Function Speed

000 255

120 149

Color Macro

Color Macros See Table 1.1 No

Function

150 179

R,G,B Chase

RGB Chase pattern

180 209

Automatic

Color Change

210 239

Automatic (Fade)

Color Change w fade

Speed

000 255

240 255

Sound Activated

Music/Auto switch

must be set to Music

Function

Function No

Function

Dimmer

000 255

Table 1.1

MODE CH 2 DESCRIPTION

000 016 Red

017 056

Red ( Full )

Green: ( 0% ~ 100% )

057 094

Green (Full

Red: ( 100% ~ 0% )

095 096 Green

097 136

Green ( Full )

Blue: ( 0% ~ 100% )

137 174

Blue ( Full )

Green: ( 100% ~ 0% )

175 176 Blue

177 216

Blue ( Full )

Red: ( 0% ~ 100% )

Color

Macro

Ch 1

120 149

217 255

Blue ( Full )

Red ( Full )

Green: ( 0% ~ 100% )

Music/Auto Switch

Note! Regardless of DMX controller

operated use, when the LED-

PAR200B is set to run in Sound

Activated mode, you should make

sure that all units are properly

switched to Music and that you have

adjusted the rotary dial to optimize the

sound level response of the unit.

SWITCH ROTARY FUNCTION

AUTO Adjusts speed of built in

program

MUSIC Adjusts sound sensitivity of

built in Mic.

Andere Handbücher für LED-PAR200B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chauvet Leuchte Handbücher

Chauvet

Chauvet LED-BANK4 Bedienungsanleitung

Chauvet

Chauvet DMX-1655R Produkthandbuch

Chauvet

Chauvet Scorpion GrafX LG-80 Bedienungsanleitung

Chauvet

Chauvet Q-Wash 419Z-LED Bedienungsanleitung

Chauvet

Chauvet Intimidator Color DMX-500 Technisches Dokument

Chauvet

Chauvet Q-Spot 575 Handbuch

Chauvet

Chauvet DMX-685 Bedienungsanleitung

Chauvet

Chauvet Intimidator Wash Zoom 350 IRC Bedienungsanleitung

Chauvet

Chauvet Intimidator COLOR LED Bedienungsanleitung

Chauvet

Chauvet Lrgrnd 300E Beam Bedienungsanleitung

Chauvet

Chauvet Moonflower Bedienungsanleitung

Chauvet

Chauvet TFX-UVLED Technisches Dokument

Chauvet

Chauvet LEDrain 38 Bedienungsanleitung

Chauvet

Chauvet LED-BANK4 Bedienungsanleitung

Chauvet

Chauvet Constellation DMX-800 Bedienungsanleitung

Chauvet

Chauvet Vue III Handbuch

Chauvet

Chauvet Vue I Bedienungsanleitung

Chauvet

Chauvet PAR56 Bedienungsanleitung

Chauvet

Chauvet Stepper Bedienungsanleitung

Chauvet

Chauvet F-40 Bedienungsanleitung

Chauvet

Chauvet COLORsphere LED-CS8 Bedienungsanleitung

Chauvet

Chauvet DMX Abyss DMX-450 Handbuch

Chauvet

Chauvet Followspot 1200 Bedienungsanleitung

Chauvet

Chauvet Q-Spot 360-LED Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung