CHC I80 GNSS Bedienungsanleitung

Andere Handbücher für i80 GNSS

13

Inhaltsverzeichnis

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung

CHC® i80 GNSS Receiver

QuickTour with FieldGenius

(Internal UHF Base Mode)

i80 GNSS Receiver Quick Tour with FieldGenius (Internal UHF Base)

1

1.Prerequisites

Hardware: CHC i80 Base with internal radio

Kit, Controller Kit,UHF Bar Antenna (450-470

MHz), Lithium Battery, Extension Pole,

Tribrach with optical plummet, Auxiliary H.I.

Tool, H.I. Tape, Tribrach adaptor, Tripod, LT30

handheld

Software: FieldGenius8

2.Steps to set i80 working as base

in internal UHF mode with

FieldGenius

2.1 Base installation

Set up base on known point or unknown

point as shown in follow figure and screw bar

antenna on base receiver.

Note: The recommend firmware version of

i80 is 1.3.36 or higher. If not, please contact

local dealer or CHC Support for latest

firmware.

2.2 Base setting in FieldGenius

1. Power on the receiver

Long press the i80 power button until the

green and blue LED lights are on.

2. Click on [start] and then FieldGenius.

3. Click [New Project] to create a project or

Click [Open] to open one exist project.

i80 GNSS Receiver Quick Tour with FieldGenius (Internal UHF Base)

2

4. A project file should be selected then

click [Continue] for next step.

5. Click on [Select Instrument]

6. Select [GNSS Reference] option then

click [Edit] to select device and linking

method

7. Click [Tolerance] tab to set base station

satellites mask, PDOP mask and elevation

mask.

i80 GNSS Receiver Quick Tour with FieldGenius (Internal UHF Base)

3

8. Click [Antenna Height] to set the base

antenna height

Note: if you want to measured the slant

height of i80,please refer to the follow

figure.

i80 GNSS Receiver Quick Tour with FieldGenius (Internal UHF Base)

4

9. Click [Model and Communication]

tab→select Make as [CHC], Model as [i80],

Port as [Bluetooth] →click [Bluetooth

Device List] to add bluetooth device

10. Click [Search] to search the around

Bluetooth device.

11. Click on the device that matches your

device serial number, then click it

i80 GNSS Receiver Quick Tour with FieldGenius (Internal UHF Base)

5

12. Type in the PIN Code of the bluetooth

then click [OK] button to finish the device

edit.

13. Then our target device can be selected in

the bluetooth device list. Click [OK] button

back to [Model and Communication]

interface.

14. The target device can be selected in the

drop-down box then click [Connect] button.

The software will build the connection to your

device

15. After successful connection, FieldGenius

will display the following hint, please click [OK]

button

i80 GNSS Receiver Quick Tour with FieldGenius (Internal UHF Base)

6

14. Click the [Known Position] icon to switch

the method of starting base

Users can start base with known points by

clicking [Known Geodetic Position], unknow

position by clicking [Averaged Geodetic

Position] and local coordinates by clicking

[Local Transformation to point]

15. After select the starting method, please

click [Start Reference] to start the base.

Please click [Set Position] to set the averaged

result as base coordinate.

i80 GNSS Receiver Quick Tour with FieldGenius (Internal UHF Base)

7

16. Select the [UHF Radio Module] from the

drop-down box then click [Setup] button to

set the radio protocol, working power and

frequency.

After setting the parameters, please click

[Ok]

Note: the protocol and the frequency must

be the same between Base and Rover.

17. Click [Connect] to finish starting base

18. Then the green LED will flash and the

states will become [Autonomous] to [float]

then to [fix],which means the rover is getting

the correction data from base.

19. The survey work can be done with the

i80