Chiayo SDR-5100M Installationshandbuch
CHIAYO ELECTRONICS CO.,LTD.
Operation manual
069 9
IR RF AF SYNCCHANNEL 1
MIN MAX MIN MAXIR RF AF SYNCCHANNEL 2
NDR-3120
DIVERSITY RECEIVER
SDR-5100M
SDR-5200M
UHF 2-Way Sync Receiver Module
1
SDR-5100/5200M IrDA UHF 2-Way Sync Receiver Module
SDR-5100/5200M IrDA receiver module
1.Channel indicator
2.Diversity A/B indicator
3.Audio signal indicator
4.IR sensor area
5.Channel Select/Scan buttons
6.IrDA synchronizing button
7.Squelch control
8.Power switch/volume control
Verify channel and frequency in use
The channel LED will show last stored frequency and channel. For
example, if channel 36 is 608.750MHz, the LED will first display 60,87,50
and 36 in sequence.
Frequency: ► ► ►Channel:
Select a channel that corresponds to the transmitter. When transmitter is
turned on, either A or B diversity indicator will light up to indicate that it is
connected.
88
2
Instructions
Changing CHANNEL
1 Press LEFT button to increase the TENS-digit channel
number.
2 Press RIGHT button to increase the UNIT-digit channel
number.
66
76
66
67
3
SDR-5100/5200M IrDA UHF 2-Way Sync Receiver Module
CHANNEL scanning
For an interference-free operation, a cleaner channel might be necessary
if the current one receives too much interference. Before scanning, the
transmitter must be switched off.
1 Press and hold either channel button for 3 seconds
2 The receiver will find and locate a clear, interference- free
channel.
scan UP
scan DOWN
42
42
76
46
42
67
36
4
Instructions
SQUELCH (SQ) setting
When interference is encountered try reducing the sensitivity of the
receiver by turning the SQ control clockwise, thus less susceptible to
interference. If this still does not solve the problem it means this frequency
is not suitable. Adjust the squelch back to where it was and use the scan
function to locate a clear, interference-free channel.
5
SDR-5100/5200M IrDA UHF 2-Way Sync Receiver Module
Channel synchronizing between receiver and transmitter
Align infrared areas of the receiver and transmitter within 10~30cm.
Changing receiver’s channel
Changing transmitter’s channel
1 Press the synchronizing button of
the transmitter.
1 Press the SYNC button of the
receiver.
2 The transmitter's LED will grow to
denote synchronizing signal
transmitted.
2 The transmitter's LED will grow to
denote synchronizing signal
received.
3 The channel number on the
receiver’s LED will become the
same as the transmitter’s, which
means the receiver has been
successfully synchronized.
3 The channel number on the
transmitter’s LCD will become the
same as the receiver’s, which
means the transmitter has been
successfully synchronized.
10~30cm
6
Instructions
If it doesn’t work check that you have the IR sensor panels aligned, that
they are facing each other, devices are within 10~30cm of each other, and
try again.
CHIAYO ELECTRONICS CO.,LTD.
Http://www.chiayo.com.tw｜Email: sales@chiayo.com.tw
Office: 30, Lane 27, Section 4, Jen-Ai Road, Taipei 10685, Taiwan
Tel: 886-2-27415741｜Fax: 886-2-27525242
Factory: 88, Chung-Hsiao Street 2, Chiayi 60080, Taiwan
Tel: 886-5-2711000｜Fax: 886-5-5767611
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Chiayo Empfänger Handbücher
Chiayo
Chiayo NDR-3110 Bedienungsanleitung
Chiayo
Chiayo SDR-5900 Bedienungsanleitung
Chiayo
Chiayo DWR-2420 Bedienungsanleitung
Chiayo
Chiayo NDR-2110 Bedienungsanleitung
Chiayo
Chiayo SDR-5200M IrDA Bedienungsanleitung
Chiayo
Chiayo SDR-5900 Bedienungsanleitung
Chiayo
Chiayo SDR-1900 Bedienungsanleitung
Chiayo
Chiayo QR-4000N Bedienungsanleitung
Chiayo
Chiayo NDR-2120 Bedienungsanleitung
Chiayo
Chiayo NDR-2120 Bedienungsanleitung
