Chicago Electric CHICAGO 46507 Bedienungsanleitung

7” POLISHER/SANDER

Model 46507

ASSEMBLY AND

OPERATING INFORMATION

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions please call 1-800-444-3353

SPECIFICATIONS TABLE

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance, and cleaning procedures, parts list and

assembly diagram. Keep your invoice with this manual. Write the invoice

number on the inside of the front cover. Keep this manual and invoice in a safe

and dry place for future reference.

GENERAL SAFETY WARNINGS AND PRECAUTIONS

1. KEEP WORK AREA CLEAN AND DRY. Cluttered, damp or wet work areas

invite injuries.

2. KEEP CHILDREN AWAY FROM WORK AREA. Do not allow children to handle

this product.

3. STORE IDLE EQUIPMENT. When not in use, tools and equipment should be

stored in a dry location to inhibit rust. Always lock up tools and equipment and

keep out of reach of children.

4. DO NOT USE THIS PRODUCT IF UNDERTHE INFLUENCE OF ALCOHOL OR

DRUGS. Read warning labels on prescriptions to determine if your judgment or

reflexes are impaired while taking drugs. If there is any doubt, do not attempt to

use this product.

5. USE EYE, BREATHING, AND HEARING PROTECTION. Wear ANSI approved

safety impact eye glasses, ANSI approved breathing protection, and ANSI

approved hearing protection when using this product. ANSI approved safety

impact eye glasses, dust masks, and hearing protectors are available from

Harbor Freight Tools.

SKU 46507 PAGE 2

Item Description

Electrical

Requirements 120V / 60 Hz / 11 Load Amp

Double Insulated Motor

1,000 - 3,000 RPM Variable Speed

16 Gauge Power Cord

Spindle Thread 5/8”-11 Threads Per Inch

Handle Mounting Threaded, 3 Positions

Wool Cover Size 8”

Tool Length 17”

Tool Weight 8.40 Lbs. With Wool Cover

96GA

E210256

Rev 12/01

6. DRESS SAFELY. Non-skid footwear or safety shoes should be used when

working with this product. Do not wear loose clothing or jewelry as they can

become caught in moving parts. Wear a protective hair covering to prevent long

hair from becoming caught in moving parts. If wearing a long-sleeve shirt, roll

sleeves up above elbows.

7. INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS.

8. DO NOT OVERREACH. Keep proper footing and balance at all times to prevent

tripping, falling, back injury, etcetera.

9. STAY ALERT. Watch what you are doing at all times. Use common sense. Do

not use this product when you are tired or distracted from the job at hand.

10. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that

it will operate properly and perform its intended function. Check for damaged

parts and any other conditions that may affect the operation of this product.

Replace or repair damaged or worn parts immediately.

11. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only

identical replacement parts. Only use accessories intended for use with this

product. Approved accessories are available from Harbor Freight Tools.

12. MAINTAIN THIS PRODUCT WITH CARE. Keep this tool clean and dry for better

and safer performance.

13. MAINTENANCE: For your safety, service and maintenance should be performed

regularly by a qualified technician.

14. USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain

applications for which this product was designed. Do not use small equipment,

tools or attachments to do the work of larger industrial equipment, tools or

attachments. Do not use this product for a purpose for which it was not intended.

SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS

1. MAKE SURE THE POWER SWITCH (part #33) IS IN THE “OFF” POSITION

BEFORE PLUGGING IN THE POWER CORD (part #36).

2. DO NOT ABUSE THE POWER CORD. Do not use the Power Cord (part #36) to

pull the Plug from a power outlet. Keep Power Cord away from heat, oil, sharp

edges, and moving parts. Replace a damaged Power Cord immediately. Route

the Power Cord safely. Protect it from being damaged by other equipment in the

work area. Do not route the Power Cord where it can be walked on or tripped

over.

SKU 46507 PAGE 3

3. IFYOU USE AN EXTENSION CORD, MAKE SURE TO USE ONLY UL

APPROVED CORDS HAVING THE CORRECT GAUGE AND LENGTH.

(SEE FIGURE A.)

REQUIRED EXTENSION CORD GAUGE

Nameplate ExtensionCord Length

Amperes 25’ 50’ 75’ 100’ 150’ 200’

0 - 5 16 16 16 14 12 12

5.1 - 8 16 16 14 12 10 -

8.1 - 12 14 14 12 10 - -

12.1 - 15 12 12 10 10 - -

15.1 - 20 10 10 10 - - -

FIGURE A

4. MAINTAIN A SAFE WORK ENVIRONMENT. Do not use this tool in or near

damp or wet areas. Do not expose this product to rain. Keep work area well lit.

Make sure there is adequate surrounding work space. Use this tool in a well

ventilated area. Do not operate this tool in the presence of flammable liquids,

gases, or dust. To avoid accidental electric shock, do not let your body come in

contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators.

5. DO NOT FORCETHE EQUIPMENT. This Polisher/Sander will do the work better

and safer at the speed and capacity for which it was designed.

6. REMOVE ALL ADJUSTING WRENCHES FROMTHE POLISHER/SANDER

BEFORETURNING IT ON.

7. AVOID UNINTENTIONAL STARTING. Make sure you are prepared to begin

work before turning the Power Switch (part #33) “ON”.

8. ALLOWTHE POLISHING DISC (part #44) ANDWOOL COVER (part #45), AS

WELL ASTHE RUBBER BACKING PLATE (#46) WHEN SANDING,TO SPIN

UPTO FULL SPEED BEFORE PRESSINGTHEM ONTOTHE WORKPIECE.

When turning off the Polisher/Sander, allow the Rubber Backing Plate or Polish-

ing Disc to spin down and stop on their own. Do not press against to stop them.

9. DO NOT FORCETHE POLISHING DISC (part #44) ANDWOOL COVER (part

#45), RUBBER BACKING PLATE (#46) WITH SANDPAPER DISC ONTOTHE

WORKPIECEWHEN USING. Apply moderate pressure, allowing the Polisher/

Sander to do the work without being forced.

10. MAKE SURETHE WORKPIECE IS FREE FROM BURRS AND ANY OTHER

FOREIGN OBJECTS WHICH COULD DAMAGE THE POLISHER/SANDER.

SKU 46507 PAGE 4

11. MAKE SURE THE WORKPIECE IS SUPPORTED AT ALL TIMES DURING

OPERATION. Use a Roller Stand (not provided) with larger workpieces if

necessary.

12. MAINTAIN CONTROL OFTHE WORKPIECE AT ALL TIMES. Whenever

possible, secure the workpiece with clamps, in a vise, etcetera.

13. ALWAYS DISCONNECTTHE POLISHER/SANDER FROM ITS ELECTRICAL

SUPPLY SOURCE WHEN NOT IN USE. Make sure to unplug the Polisher/

Sander when leaving the work area, moving the tool from one location to an-

other, handing the Polisher/Sander to another person, changing the Polishing/

Rubber Backing Plate disc.

14. THISTOOL IS INTENDEDTO BE USED ONLY AS A POLISHER AND AS A

SANDER. DO NOT ATTEMPTTO USETHISTOOL AS AN ANGLE GRINDER

OR IN ANY OTHERWAYTHAN ITS INTENDED PURPOSE. NEVER INSTALL

A CARBIDETIPPED OR STEEL CIRCULAR SAW BLADE FOR USE INTHIS

POLISHER/SANDER. NEVER INSTALL A WOOD CARVING BLADE, CARV-

ING DISC WITH CHAIN SAW CUTTERS, OR A CUTTING CARVING DISC ON

THIS POLISHER/SANDER.

15. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities, contain chemicals known (to the State of California)

to cause cancer, birth defects or other reproductive harm. Some examples of

these chemicals are: lead from lead-based paints, crystalline silica from bricks

and cement or other masonry products, arsenic and chromium from chemically

treated lumber. Your risk from these exposures varies, depending on how often

you do this type of work. To reduce your exposure to these chemicals: work in a

well ventilated area, and work with approved safety equipment, such as those

dust masks that are specially designed to filter out microscopic particles.

(California Health & Safety Code 25249.5 et seq.)

16. WARNING: People with pacemakers should consult with their physician(s)

before using this product. Operation of equipment in close proximity to a heart

pacemaker could cause interference or failure of the pacemaker.

UNPACKING

When unpacking, check to make sure all parts shown on the Parts List (page 11) are

included. If any parts are missing or broken, please call Harbor Freight Tools at the

number shown on the cover of this manual as soon as possible.

SKU 46507 PAGE 5

ASSEMBLY INSTRUCTIONS

NOTE: For additional references to the parts listed below, refer to the Assembly

Diagram on page 11 of this manual.

To Attach The Polishing Disc And Wool Cover:

1. Caution: Prior to installing the Wool Compounding Bonnet (part #44), make sure

the Polisher/Sander is disconnected from its electrical power source.

2. Place the Adaptor (part #1) on the Spindle (part #3) of the Polisher/Sander, and

place theWool Compounding Bonnet (part #44) on the Adaptor (See Figure B,

and Assy. Diagram.)

3. Depress the Brake Pin (part #18) to keep the Spindle (part #3) from turning, and

hand

screw the Adaptor (part #1) onto the Spindle. (See Figures B, C,and Assy.

Diagram.)

4. Then, use the Spanner (part #43) provided to keep the Adaptor (part #1) from

turning, and firmly hand tighten theWool Compounding Bonnet onto the Adaptor.

(See Figures B, C, and Assy. Diagram.)

ADAPTOR(#1)

SPINDLE(#3)

BRAKEPIN (#18)

WOOLCOMPOUNDINGBONNET(#44)

SWITCH (#33)

BRUSHCAP(#40)

CARBONBRUSH(#41)

BRUSHHOLDER(#42)

(Qty.2 EACH)

VARIABLE SWITCH (#31)

SWITCH LOCK

BACK HANDLE (#39)

FIGURE B

SKU 46507 PAGE 6 REV 09/02 REV 06/05

IMPORTANT

Carefully inspect the condition of the accessory before use and check the accessory

continually during use. If any damage is noted, stop immediately and replace the

accessory withan undamagedone. Harbor FreightTools cannot be held responsible

for damage caused by using a damaged accessory on this tool.

To Attach The Side Handle:

1. NOTE: The Side Handle (part #20) may be attached either on the right, left, or

top side of the Polisher/Sander. (See Figure C, and Assy. Diagram.)

2. To attach the Side Handle (part #20), remove the Rubber Plunge (part #19) from

either the right, left, or top side of the Polisher/Sander in order to expose the

threaded mounting hole. (See Figure C, and Assy. Diagram.)

3. Firmly

hand

tighten the threaded portion of the Side Handle (part #20) into the

desired mounting hole of the Polisher/Sander. (See Figure C, and Assy. Dia-

gram.)

MOUNTING

HOLE

BRAKE PIN (#18)

MOUNTING HOLE

SIDE HANDLE (#20)

WOOL COVER (#45)

BRUSH CAP (#40)

CARBON BRUSH (#41)

BRUSH HOLDER (#42)

VARIABLE SWITCH (#31)

BACK HANDLE (#39)

POWER CORD (#36)

MOUNTING HOLE

BRUSH CAP (#40)

CARBON BRUSH (#41)

BRUSH HOLDER (#42)

SWITCH

LOCK

FIGURE C

OPERATING INSTRUCTIONS

NOTE: For additional references to the parts listed below, refer to the Assembly

Diagram on page 12 of this manual.

SKU 46507 PAGE 8

SKU 46507 PAGE 7

To AttachThe Rubber Backing Plate And Sandpaper:

1. Caution: Prior to installing the Rubber Backing Plate (part #46), make sure the

Polisher/Sander is disconnected from its electrical power source.

2. Rest the tool on a flat surface. Depress the Brake Pin (#18) to keep the Spindle

(#3) from turning.

3. Screw the Rubber Backing Plate (46) onto the threaded end of the Spindle (#3)

until it is snug. (See diagram below)

4. Ahere Sandpaper Disc (not included) evenly across the Rubber Backing Plate.

The Rubber Backing Plate has a self-sticking backing, so be sure only to use

Sandpaper Discs with a self-sticking material. Press Sandpaper Disc firmly onto

pad. When finished, release pressure on the Brake Pin (#18).

5. When finished sanding, peel the Sandpaper Disc away from the Plate.

BRAKE PIN (#18)

RUBBER BACKING PLATE (#46)

SPINDLE (#3)

SANDPAPER DISC

SKU 46507 PAGE 9

1. Caution: Check to make sure the Switch (part #33) is in its “OFF” position before

plugging the Power Cord (part #36) into a 110-120 Volt, grounded,

electrical power outlet. (See Figures B, C, and Assy. Diagram.)

2. Make sure to use both hands to

firmly

grip the Polisher/Sander by its Side

Handle (part #20) and Back Handle (part #39). (See Figures B, C, and Assy.

Diagram.)

3. To turn on the Polisher/Sander, squeeze the Switch (part #33). To turn off the

Polisher/Sander, release pressure on the Switch. NOTE: For automatic, continu-

ous running, squeeze the Switch while, at the same time, depressing the Switch

Lock. This locks the Switch in its “ON” position. To turn off the Polisher/Sander,

squeeze and quickly release pressure on the Switch. This unlocks the Switch,

and allows the Polisher/Sander to automatically turn off. (See Figures B, C, and

Assy. Diagram.)

4. Allow the Polisher/Sander to spin up to full speed before pressing it onto the

workpiece. (See Figures B, C, and Assy. Diagram.)

5. NOTE: The Polisher/Sander can be operated at different speeds (from 1,000

RPM to up to 3,000 RPM), depending on the material of the workpiece. To

change speeds,

make sure the Polisher/Sander is off.

Then, select the desired

speed, using the Variable Switch (part #31). (See Figures B, C, and Assy.

Diagram.)

6. Do not force the Polisher/Sander onto the workpiece. Apply moderate pressure,

allowing the Polisher/Sander to do the work without being forced. (See Figures

B, C, and Assy. Diagram.)

7. Move the Polisher/Sander along the workpiece in small, circular, patterns. (See

Figures B, C, and Assy. Diagram.)

8. When finished, turn off the Polisher/Sander and allow the Polishing Disc or the

Rubber Backing Plate to spin down and stop on their own. Do not press against

the disc to stop them. (See Figures B, C, and Assy. Diagram.)

INSPECTION, MAINTENANCE, AND CLEANING

Caution:

Always disconnect the Polisher/Sander from its electrical power supply

source before performing any inspection, maintenance, or cleaning.

2. Before each use, inspect the general condition of the Polisher/Sander. Inspect

switch, power plug and cord assembly, and extension cord (if used) for damage.

Check for loose screws, misalignment, binding of moving parts, broken, cracked,

or improper mounting of the Polishing Disc or the Rubber Backing Plate, broken

SKU 46507 PAGE 10

parts and any other condition that may affect its safe operation. If abnormal

noise or vibration occurs, turn off the Polisher/Sander immediately and have the

problem corrected before further use. Do not use damaged equipment.

3. The Polisher/Sander features

two

Carbon Brushes (part #41) which, periodically,

should be examined for wear. The Carbon Brushes are located on each side of

the Plastic Housing (part #29). To inspect or replace the Carbon Brushes, use a

small standard screwdriver to remove the Brush Cap (part #40). Examine the

concave surface of the Carbon Brushes. The surface should be smooth and

clean. If there are large scratch marks in the Brushes, or parts of the Brushes

have broken off, replace

both

Brushes immediately with approved replacement

Brushes from Harbor Freight Tools. To reinstall the Brushes, insert them into the

two

Brush Holders (part #42). Turn the Brushes vertically so they will fit into the

Brush Holders. Then, replace the Brush Caps. (See Figures B, C, and Assy.

Diagram.)

4. Do not use solvents to wipe off the Polisher/Sander, as damage may result. If

necessary, wipe with a damp cloth. You may use a mild detergent.

5. Do not introduce water, dirt, or dust into the electric motor through the motor

vents.

6. Once clean, lubricate all moving parts with a light oil.

7. When storing, keep the Polisher/Sander covered with a cloth cover.

PLEASE READTHE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS

MANUAL AS A REFERENCETOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR

SHE IS QUALIFIEDTO MAKE ANY REPAIRS TOTHE PRODUCT ORTHAT HE OR SHE IS QUALI-

FIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR

DISTRIBUTOREXPRESSLY STATESTHATALL REPAIRS ANDPARTSREPLACEMENTSSHOULD

BEUNDERTAKEN BY CERTIFIEDAND LICENSEDTECHNICIANS AND NOTBYTHEBUYER. THE

BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTSTHERETO.

Inhaltsverzeichnis

Andere Chicago Electric Sander Handbücher

Chicago Electric

Chicago Electric 67256 Installationshandbuch

Chicago Electric

Chicago Electric 93431 Bedienungsanleitung

Chicago Electric

Chicago Electric 92194 Bedienungsanleitung

Chicago Electric

Chicago Electric 90820 Bedienungsanleitung

Chicago Electric

Chicago Electric 94748 Stücklistenhandbuch

Chicago Electric

Chicago Electric 69924 Bedienungsanleitung

Chicago Electric

Chicago Electric 90045 Bedienungsanleitung

Chicago Electric

Chicago Electric 40118 Bedienungsanleitung

Chicago Electric

Chicago Electric 45813 Bedienungsanleitung

Chicago Electric

Chicago Electric 69820 Montageanleitung

Chicago Electric

Chicago Electric 94338 Montageanleitung

Chicago Electric

Chicago Electric 92158 Stücklistenhandbuch

Chicago Electric

Chicago Electric 62216 Original Bedienungsanleitung

Chicago Electric

Chicago Electric 95020 Bedienungsanleitung

Chicago Electric

Chicago Electric 42864 Stücklistenhandbuch

Chicago Electric

Chicago Electric 66615 Installationshandbuch

Chicago Electric

Chicago Electric 66891 Installationshandbuch

Chicago Electric

Chicago Electric 69696 Montageanleitung

Chicago Electric

Chicago Electric 69924 Montageanleitung

Chicago Electric

Chicago Electric 95020 Stücklistenhandbuch

Chicago Electric

Chicago Electric 41213 Installationshandbuch

Chicago Electric

Chicago Electric 93431 Installationshandbuch

Chicago Electric

Chicago Electric 96435 Installationshandbuch

Chicago Electric

Chicago Electric 92623 Bedienungsanleitung

Beliebte Sander Handbücher anderer Marken

Oliver

Oliver 6305 Bedienungsanleitung

Jet

Jet 22-44 Pro-3 Service-Handbuch

Makita

Makita M9204 Handbuch

Makita

Makita M9204 Bedienungsanleitung

Craftsman

Craftsman 351.215131 Bedienungsanleitung

Clarke

Clarke Woodworker CBS1-5B Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP9778 Bedienungsanleitung

Nitto Kohki

Nitto Kohki BB-20 Bedienungsanleitung

Ferm

Ferm FEOS-135 Bedienungsanleitung

Unior

Unior 1510 Bedienungsanleitung

stayer

stayer ls1200 Bedienungsanleitung

Jet

Jet JSG-96 Service-Handbuch

Parkside

Parkside PDS 290 B2 Bedienungsanleitung

Status

Status XPA Series Bedienungsanleitung

Clarke

Clarke EZ Sand Bedienungsanleitung

Craftsman

Craftsman 113.22521 Bedienungsanleitung

Craftsman

Craftsman 113.225831 Bedienungsanleitung

CLAS

CLAS OP 1429 Bedienungsanleitung