CHIEF UPM-2401 Bedienungsanleitung

Universal Pitch Adjustable Wall Mount

For Flat Panel Display

UPM-2401

Secures Display

Can Be Used to

Lock Display

Your new Chief Universal Pitch-Adjustable Wall

Mount (UPM-2401) is a quick disconnect mounting sys-

tem with adjustability between 0 and 15 degrees pitch.

The optional lateral shift bracket (PAC-125) allows 4”

lateral shift on either side of a 16” center stud or spans a

24” on center stud system.

Once the Chief Universal Flat Panel Display Wall

Mount Bracket is attached to your display, simply attach

the mount securely on a wall, lock the display in place

using the convenient Q-latch, and attach your audio/

video cables.

The UPM-2400 is virtually invisible when your display

is mounted.

BEFORE YOU BEGIN

•Caution: To prevent damage to the mount, which could void factory warranty and affect the attached equipment,

thoroughly study all instructions and illustrations before you begin the installation. Pay particular attention to the

“Important Warnings and Precautions” on Page 1.

• The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the mount must

be capable of supporting five times the total weight of the equipment.

• The maximum weight to be installed on the Universal Flat Panel Display Wall Mount is 125 pounds (56.7 Kg).

• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.

CHIEF MANUFACTURING INC.

1-800-582-6480 952-894-6280 FAX 952-894-6918

12800 HIGHWAY 13 SOUTH, SUITE 500

SAVAGE, MINNESOTA 55378 USA

PART NO. 8805-000018 (Rev. A)

2002 Chief Manufacturing

www.chiefmfg.com

Printed in USA 04-03

INSTALLATION INSTRUCTIONS

Installation Instructions 14X24 Universal Pitch-Adjustable Mount

IMPORTANT WARNINGS AND PRECAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre-

sponding instructions.

•WARNING: Improper installation can result in serious personal injury! Make sure that the structural members can

support a weight factor five times the total weight of the equipment. If not, reinforce the structure before

installing the mount.

•WARNING: Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.

•WARNING: The installer is responsible for verifying that the wall to which the mount is anchored will safely support

the combined load of all attached components or other equipment.

•WARNING: Watch for pinch points. Do not put your fingers between movable parts.

•WARNING: Make sure the mount and brackets are correctly oriented.

•WARNING: Make sure the latching flag securing the display is completely engaged at all times except when removing

or installing the display. The latching flag must be all completely engaged when installing/removing

cables.

•CAUTION: Check the unit for shipping damage before you begin the installation.

•CAUTION: Use only the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

CONTENTS

DIMENSIONAL DRAWING .............................. 2

INSTALL MOUNT .............................................. 3

INSTALL DISPLAY BRACKETS ...................... 3

MOUNT THE DISPLAY .................................... 3

PARTS ................................................................. 4

TOOLS REQUIRED FOR INSTALLATION

• Phillips screwdrivers, No. 1 and No. 2 TIP

• Drill and bit set

• Wrench set

NOTE: Other tools may be required depending on the

method of installation.

Installation Instructions 14X24 Universal Pitch-Adjustable Mount

26 1/8"

16"

1 1/8" 1 3/8"

5/16"

5" 8 5/8"

16"

5 1/16"

2 3/8"

10"

INTERFACE BRACKETS ADD APPROXIMATELY 1/2" TO DEPTH OF MOUNT

1 1/2"

DIMENSIONAL DRAWING

Installation Instructions 14X24 Universal Pitch-Adjustable Mount

INSTALL MOUNT

Install the mount as follows:

1. Determine the exact mounting location prior to installation and

draw a level line to indicate the desired height for the top of the

mounting plate.

WARNING: Improper installation can result in serious per-

sonal injury! Make sure that the structural

framework can support a weight factor five times

the total weight of the equipment. If not, rein-

force the structure before installing the mount.

2. With the mount correctly oriented and level, secure the mount

to the wall (see Figure 1) using four fasteners (not included).

Fasteners must be driven into the supporting wall studs or other

supporting framework.

3. Check mount to ensure it is level and adjust to level if

necessary.

INSTALL DISPLAY BRACKETS

Install display bracket(s) according to the instructions provided.

The bracket(s) is/are designed for your specific model.

MOUNT THE DISPLAY

Mount the display as follows:

1. Make sure no power is supplied to the display and the flags are

in the lowered (open) position before attempting to mount the

display.

2. Using two people, slide the display down over the mount.

Make sure all four Q-buttons of the display engage all four

slots in the mount.

3. With the Q-buttons of the display fully engaged in the slots of

the mount, secure the display on the mount by raising the flags

all the way to their locked position. If the flags do not fully

engage, remove the display and make sure the brackets are

correctly installed.

NOTE: A security lock may be installed through the hole in the

locking flag for additional security (see Figure 2).

NOTE: If display does not remain at desired tilt setting, tighten

the nut and bolt on tilt arms on each side (see Figure 2 and Figure 3).

WARNING: Make sure the flag securing the display is com-

pletely lowered at all times except when removing

or installing the display. The flag must be all the

way down when installing/removing cables.

Figure 2. Optional Security & Adjust Tilt

Security Lock

May Be

Installed

Loosen or tighten this bolt

to adjust tilt tension

Mounting

Holes

Mounting

Holes

Figure 1. Mounting Hole Locations

Loosen or tighten this nut

Loosen or tighten

to adjust tilt tension

this bolt

Figure 3. Tilt Tension Adjustment

Installation Instructions 14X24 Universal Pitch-Adjustable Mount

PARTS

Table 1: Parts

Ref Description Qty Ref Description Qty

1 LINK, Upper, Right 1 13 SPACER, Steel, 3/8” 2

2 LINK, Upper, Left 1 14 SPACER, Steel, 3/4” 2

3 LINK, Center 2 15 BOLT, Hex, 3/4” 2

4 LINK, Lower 2 16 SPACER, Nylon, 1/2”X.32ID 2

5 BRACKET, Mount, Right 1 17 NUT, Acorn, 1/4-20 2

6 BRACKET, Mount, Left 1 18 FLAG, Extended 1

7 NUT, Lock, 1/4-20 10 19 SCREW, 10-24X1/2, FH 1

8 WASHER, Belleville 6 20 WASHER, Nylon 2

9 SPACER, Nylon, 1/16” X .32ID 10 21 NUT, Nylock, 10-24 2

10 SPACER, Nylon, 1/4” X .32ID 2 22 FLAG, Locking 1

11 SPACER, Nylon, 1/4” X .26ID 4 23 SCREW, 10-24X1/2, Phillips 1

Installation Instructions 14X24 Universal Pitch-Adjustable Mount

12 12

19 20 21

Inhaltsverzeichnis

Andere CHIEF Rack & Stand Handbücher

CHIEF

CHIEF MCD Series Bedienungsanleitung

CHIEF

CHIEF CM2C40 Bedienungsanleitung

CHIEF

CHIEF KSA-1020 Bedienungsanleitung

CHIEF

CHIEF SSB-850 Bedienungsanleitung

CHIEF

CHIEF raxxess series Bedienungsanleitung

CHIEF

CHIEF MSP-YM4 Bedienungsanleitung

CHIEF

CHIEF LCD Swivel Stand MSS6000 Bedienungsanleitung

CHIEF

CHIEF FWV-110 Bedienungsanleitung

CHIEF

CHIEF FCA613 Bedienungsanleitung

CHIEF

CHIEF MWC Series Bedienungsanleitung

CHIEF

CHIEF SSB-171 Bedienungsanleitung

CHIEF

CHIEF Flexlink KXC Series Bedienungsanleitung

CHIEF

CHIEF CM7W12U Bedienungsanleitung

CHIEF

CHIEF TS318SU Bedienungsanleitung

CHIEF

CHIEF KTA-1007 Bedienungsanleitung

CHIEF

CHIEF PSB-2144 Bedienungsanleitung

CHIEF

CHIEF MTM1U Bedienungsanleitung

CHIEF

CHIEF KFCD-110 Bedienungsanleitung

CHIEF

CHIEF LBM Series Bedienungsanleitung

CHIEF

CHIEF CMA395 Bedienungsanleitung

CHIEF

CHIEF NE1F20 Bedienungsanleitung

CHIEF

CHIEF Vibration Mount CMA-347 Bedienungsanleitung

CHIEF

CHIEF PNRIW Series Bedienungsanleitung

CHIEF

CHIEF Truss/Pole Static Mount TPS-2000 Series Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung