Christie Mirage SST Montageanleitung
Installation and Setup Guide
020-102956-08
Mirage SST
NOTICES
COPYRIGHT AND TRADEMARKS
Copyright © 2022 Christie Digital Systems USA Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this
document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary
depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on
information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied
warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection
with the performance or use of this material. Our centers of excellence for manufacturing in Kitchener, Ontario, Canada and in Shenzhen, China are ISO
9001:2015 Quality Management System-certified.
For the most current technical documentation and office contact information, visit http://www.christiedigital.com.
Warranty
Products are warranted under Christie’s standard limited warranty, the details of which are available at https://www.christiedigital.com/help-center/
warranties/ or by contacting your Christie dealer or Christie.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in
accordance with the maintenance schedule specified by Christie, will void the warranty.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at the user’s own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment
CAN ICES-3 (A) / NMB-3 (A)
이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.
ENVIRONMENTAL
The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical
and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according
to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products.
If printing this document, consider printing only the pages you need and select the double-sided option.
Please help us to conserve the environment we live in!
Content
Introduction...................................................... 6
Important safeguards.................................................6
Safety and warning guidelines......................................... 6
Installation safety and warning guidelines..................................7
AC power precautions...............................................8
Laser safety precautions.............................................8
Light intensity hazard distance.........................................9
Third-party products...............................................13
Product labels.....................................................13
General hazards................................................. 13
Mandatory action.................................................14
Electrical labels..................................................15
Laser labels....................................................15
Additional safety hazards............................................15
Product documentation...............................................16
Related documentation.............................................16
Technical support...................................................16
Projector overview..................................................17
Contact your dealer.................................................17
Key features......................................................17
How the projector works..............................................18
List of components..................................................18
Chiller and laser illumination source components...............................18
Installation and setup..............................................19
Site requirements.................................................. 19
Physical operating environment........................................19
Power connection................................................ 19
Projector components................................................20
IR/wired remote keypad..............................................22
Display panel components.............................................24
Workflow: Installing and setting up the Mirage SST system........................ 24
Setting up the projector head...........................................26
Leveling the projector..............................................26
Mirage SST Installation and Setup Guide 3
020-102956-08 Rev. 1 (09-2022)
Copyright © 2022 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
Installing the projector lens..........................................27
Connecting the projector head to AC power................................ 28
Setting up the laser illumination source.....................................28
Installing the J33 terminal block on the laser illumination source...................29
Protecting the fiber connector.........................................30
Connecting the fiber optic cable to the projector through the curved strain relief.........33
Connecting the fiber optic cable to the projector through the straight strain relief.........35
Connecting the Ethernet cable to the projector..............................38
Setting up the chiller unit............................................. 39
Performing initial system start-up........................................ 40
Turning on the system............................................. 42
Turning off the system............................................. 45
Projector LED status indicators........................................46
Projector LED shutter indicators....................................... 47
Calibrating the lens motor.............................................47
Removing the projection lens.........................................47
Aligning the image..................................................48
Selecting a test pattern.............................................49
Adjusting offset..................................................49
Adjusting boresight............................................... 49
Adjusting the fold mirror............................................51
Optimizing the integrator zoom and focus................................. 53
Adjusting DMD convergence..........................................55
Aligning the image with lens zoom and focus............................... 56
Running Auto Setup to optimize display settings............................. 56
Configuring Mirage SST to work with Christie Link.............................. 57
Disposing of the product packaging....................................... 57
Connecting devices and establishing communication.....................58
IMXB ports.......................................................58
Connecting a video source using 3G input card................................59
Connecting a video source using DVI...................................... 59
Connecting a video source using DisplayPort..................................60
Connecting a video source using HDMI.....................................60
Connecting a video source using HBMIC.................................... 60
Connecting a video source using TSIC......................................60
Selecting a video source..............................................61
Connecting to a computer or server.......................................61
Configuring the RS232 port............................................ 62
Content
Mirage SST Installation and Setup Guide 4
020-102956-08 Rev. 1 (09-2022)
Copyright © 2022 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
Setting up the Ethernet...............................................62
3D setup........................................................63
3D requirements...................................................63
Hardware requirements.............................................63
Software and content requirements.....................................63
3D system timing.................................................. 64
3D input video configurations...........................................64
Setting up a single projector to display 3D content..............................64
Enabling 3D mode................................................64
Confirming the emitter setup......................................... 65
Configuring the projector for the 3D source................................ 65
Connecting devices to the 3D sync ports....................................65
Regulatory...................................................... 67
Safety......................................................... 67
Electro-magnetic compatibility.......................................... 67
Emissions..................................................... 67
Immunity..................................................... 67
Environmental.................................................... 67
Signal connectivity specifications for ................................. 69
HBMIC video formats................................................69
TSIC video formats................................................. 71
QDPIC video formats................................................ 71
TDPIC video formats................................................ 72
DDIC video formats.................................................72
THIC video formats................................................. 73
3GIC video formats.................................................73
Dual-input 3D and HFR 2D.............................................74
Content
Mirage SST Installation and Setup Guide 5
020-102956-08 Rev. 1 (09-2022)
Copyright © 2022 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
Introduction
This manual is intended for professionally trained operators of Christie high-brightness projection
systems.
The illustrations in this document are for representation only and may not depict your projector model
exactly.
Only Christie qualified technicians who are knowledgeable about the hazards associated with laser use,
high-voltage, and the high temperatures generated by the projector lasers are authorized to
assemble, install, and service the projector.
For complete Mirage SST product documentation and technical support, go to www.christiedigital.com.
Important safeguards
To prevent personal injury and to protect the device from damage, read and follow these safety
precautions. This projector is intended for use in a non-cinema environment.
Safety and warning guidelines
Read all safety and warning guidelines before installing or operating the projector.
This projector is intended for use in a fixed install environment (also known as a cinema environment).
This projector must be operated in an environment that meets the operating range specification. Use
only the attachments and/or accessories recommended by Christie. Use of others may result in the
risk of fire, shock, or personal injury.
Warning! If not avoided, the following could result in death or serious injury.
• This product must be operated in an environment that meets the operating range as specified in
this document.
• Do not look directly into the lens when the light source is on. The extremely high brightness can
cause permanent eye damage.
• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.
• FIRE HAZARD! Keep hands, clothes, and all combustible material away from the concentrated
light beam of the projector.
• Keep fingers and other body parts away from the moving parts in the product. Tie back long
hair, and remove jewelry and loose clothing before manually adjusting the product.
• FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts
specified by Christie.
• Do not operate the product without a lens installed.
• Always use a lens plug when installing or moving the product. This prevents contaminants from
entering the product.
• RADIATION HAZARD! Use of controls or adjustments, or performing procedures other than those
specified may result in hazardous radiation exposure.
Mirage SST Installation and Setup Guide 6
020-102956-08 Rev. 1 (09-2022)
Copyright © 2022 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
Caution! If not avoided, the following could result in minor or moderate injury.
• TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be
tripped over, or damaged by persons walking on or objects rolling over the cables.
Installation safety and warning guidelines
Read all safety and warning guidelines before installing the projector.
Warning! If not avoided, the following could result in death or serious injury.
• Possible hazardous optical radiation emitted from this product. (Risk group 3)
• Christie products must be installed and serviced by Christie qualified technicians.
• Do not operate the product without all of its covers in place.
• A minimum of two people or appropriately rated lift equipment is required to safely lift, install,
or move the product.
• Always install safety straps when the frame and projector are installed overhead.
• Observe load ratings and applicable local safety codes.
• When installing the projector in portrait mode, the rigging device must have a sufficient load
rating, as identified in this manual.
•
• This product must be installed within a restricted access location not accessible by the general
public.
• Install the product so users and the audience cannot enter the restricted area at eye level.
• Only personnel who are trained on the precautions for the restricted access location can be
granted entry to the area.
• Only Christie qualified technicians are permitted to open product enclosures.
Caution! If not avoided, the following could result in minor or moderate injury.
• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.
• Only Christie qualified technicians are authorized to use the tools provided in the toolbox.
Introduction
Mirage SST Installation and Setup Guide 7
020-102956-08 Rev. 1 (09-2022)
Copyright © 2022 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
AC power precautions
Read all safety and warning guidelines before connecting to AC power.
Warning! If not avoided, the following could result in death or serious injury.
• SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by
Christie.
• FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and
power plug meet the appropriate local rating standards.
• SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage
and current, as specified on the license label.
• SHOCK HAZARD! The AC power cord must be inserted into an outlet with grounding.
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product
by Christie qualified technicians or electricians before it can be connected to power.
• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,
removing components, or opening any enclosure.
• Install the product near an easily accessible AC receptacle.
Caution! If not avoided, the following could result in minor or moderate injury.
• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.
• FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.
• SHOCK HAZARD! Power supply uses double pole/neutral fusing. Disconnect all power sources
before opening the product.
Laser safety precautions
Read all safety and warning guidelines before operating the projector laser.
Warning! If not avoided, the following could result in death or serious injury.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be
permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC
62471-5:2015.
• LASER RADIATION HAZARD! This projector has an external Class 4 laser module. Never attempt
to disassemble or modify the laser module.
• Possible hazardous optical radiation emitted from this product. (Risk group 3)
• Only Christie qualified technicians who are knowledgeable about the hazards associated with
laser use, high-voltage, and high temperatures generated by the product are authorized to
assemble, install, and service the Christie Laser Projection System.
• RADIATION HAZARD! Use of controls or adjustments, or performing procedures other than those
specified may result in hazardous radiation exposure.
• Do not look directly into the lens when the light source is on. The extremely high brightness can
cause permanent eye damage.
• Do not operate the product without all of its covers in place.
• LASER RADIATION! Do not short the contact rings.
• Always keep a protective cap on disconnected fiber optic cables.
Introduction
Mirage SST Installation and Setup Guide 8
020-102956-08 Rev. 1 (09-2022)
Copyright © 2022 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
Light intensity hazard distance
This projector has been classified as Risk Group 3 as per the IEC 62471-5:2015 standard due to
possible hazardous optical and thermal radiation being emitted.
Warning! If not avoided, the following could result in serious injury.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be
permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC
62471-5:2015.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam
within the hazard distance or install the product at the height that prevents exposure of
spectators' eyes within the hazard distance. The hazard zone must be no lower than 3.0 meters
above the floor and the horizontal clearance to the hazard zone must be a minimum 2.5 meters.
• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.
The following show the zones for ocular and skin hazard distances.
• A—Hazard zone. The region of space where the projection light from the laser-illuminated
projector is above emission limits for Risk Group 2. The light intensity may cause eye damage
after a momentary or brief exposure (before a person can avert his or her eyes away from the
light source). The light may cause skin burns to occur.
• B—Hazard distance. Operators must control access to the beam within the hazard distance or
install the product preventing potential exposure of the spectators' eyes from being in the
hazard distance.
• C—No access zone. Horizontal clearance of the no access zone must be a minimum of 2.5
meters.
• D—Vertical distance to hazard zone. The hazard zone must be no lower than 3.0 meters above
the floor.
If the vertical distance to hazard zone requirement (Zone D) is satisfied, the horizontal
clearance distance (Zone C) is not needed.
• E—Represents the top view of the projector.
• F—Represents the side view of the projector.
Introduction
Mirage SST Installation and Setup Guide 9
020-102956-08 Rev. 1 (09-2022)
Copyright © 2022 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
The following table lists the hazard distance for the Christie projector lens with the zoom adjusted to
its most hazardous position.
For US and international hazard distances based upon IEC 62471-5:2015, Photobiological Safety of
Lamps and Lamp Systems – Part 5: Image Projectors.
Projection lens Part number Hazard distance (m)
Type A* Types B, C, D, E*
High brightness (HB) lenses
0.38:1 4K enhanced 144-136101-XX 1.0 1.0
0.72:1 HB fixed 144-110103-XX 1.0 1.0
0.9:1 fixed lens 144-111014-XX 1.2 1.0
1.13-1.31:1 HB zoom
(Discontinued)
144-103105-XX 1.6 1.4
1.13-1.66:1 HB zoom 144-129103-XX 2.1 1.8
1.31-1.63:1 HB zoom 144-104106-XX 2.1 1.8
1.45-2.17:1 HB zoom 144-130105-XX 2.8 2.5
1.63-2.17:1 HB zoom
(Discontinued)
144-105107-XX 2.7 2.4
1.95-3.26:1 HB zoom 144-131106-XX 4.1 3.6
1.99-2.71:1 HB zoom 144-106108-XX 3.4 3.0
2.71-3.89:1 HB zoom 144-107109-XX 4.8 4.3
3.89-5.43:1 HB zoom 144-108100-XX 7.0 6.0
4.98-7.69:1 HB zoom 144-109101-XX 9.9 8.6
Ultra high contrast (UHC) lenses
0.72:1 UHC fixed 163-116109-XX 1.0 1.0
0.9:1 UHC fixed 163-117100-XX 1.0 1.0
1.13-1.66 UHC zoom 163-118101-XX 1.7 1.6
1.45-2.17 UHC zoom 163-119102-XX 2.3 2.1
1.95-3.26 UHC zoom 163-120103-XX 3.4 3.1
2.71-3.89 UHC zoom 163-121105-XX 3.8 3.6
3.89-5.43 UHC zoom 163-122106-XX 5.4 5.1
* For specific Christie-supplied model names and part numbers, refer to the Mirage SST Projector
Head Specifications Guide (P/N: 020-102994-XX).
Type A 168-1011XX-XX
Type B 168-1061XX-XX
Type C 168-1071XX-XX
Type D 168-1081XX-XX
Introduction
Mirage SST Installation and Setup Guide 10
020-102956-08 Rev. 1 (09-2022)
Copyright © 2022 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
Andere Handbücher für Mirage SST
4
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Christie Projektor Handbücher
Christie
Christie Roadie HD+35K Bedienungsanleitung
Christie
Christie Mirage S+3K Bedienungsanleitung
Christie
Christie M Series Bedienungsanleitung
Christie
Christie LX501 Bedienungsanleitung
Christie
Christie Inspire Series Bedienungsanleitung
Christie
Christie Vivid Blue Bedienungsanleitung
Christie
Christie LX1750 Montage- und Wartungsanleitung
Christie
Christie LX505 Bedienungsanleitung
Christie
Christie D4K35 Bedienungsanleitung
Christie
Christie D4KLH60 Mirage 4KLH Bedienungsanleitung
Christie
Christie HS 2K Series Bedienungsanleitung
Christie
Christie Mirage 10000 Bedienungsanleitung
Christie
Christie 38-VIV208-03 Bedienungsanleitung
Christie
Christie DHD800 Bedienungsanleitung
Christie
Christie LX501 Kurzanleitung
Christie
Christie DWU951 Bedienungsanleitung
Christie
Christie DWU951 Bedienungsanleitung
Christie
Christie GraphXMASTER DLV1400-DX Bedienungsanleitung
Christie
Christie LX380 Bedienungsanleitung
Christie
Christie Solaria CP2210 Service-Handbuch
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
