Christie Vivid LX41 Bedienungsanleitung

LX41/LW41

User Manual - Instant Stack Guide

020-000509-01

LX41/LW41 User Manual - Instant Stack Guide 020-000509-01 Rev.1 (06-2012)

Projector

LX41/LW41

User Manual

Instant Stack Guide

Thank you for purchasing this product.

This manual is intended to explain only Instant Stack feature. Other than what is

mentioned in this manual, please see other manuals of this product.

WARNING ►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

►Follow all the instructions in the manuals or on the product. The manufacturer

assumes no responsibility for any damage caused by mishandling that is beyond

normal usage dened in the manuals.

NOTE • The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

Trademark acknowledgment

All the trademarks in this manual are the properties of their respective owners.

Features

This projector can be used with another projector of the same type to project an

image on the same screen using the Instant Stack feature.

The two projectors can be operated simultaneously to make the image brighter.

Moreover, if you connect two projectors with RS-232C cross-over cable, it turns to

a kind of intellectual stacking system. The two projectors can work alternately by

themselves, and once one projector has an accident the other voluntarily starts to

work to keep your presentation going.

These features, generically called Instant Stack, provide you with the broad use.

LX41/LW41 User Manual - Instant Stack Guide 020-000509-01 Rev.1 (06-2012)

  

1. Introduction ........................3

1.1 Entries and graphical

symbols explanation........................ 3

1.2 Important safety instruction .......... 3

Instant Stack feature............................ 3

General installation .............................. 5

1.3 Basic information

and preparations ............................. 6

Instant Stack ........................................ 6

Intellectual Stack and Simple Stack..... 6

Remote control for Intellectual Stack

and Simple Stack .............................6

Installation styles ................................. 6

Tentative terms for the two projectors.. 6

2. Installation ..........................7

2.1 Preparing for Intellectual Stack..... 7

2.2 Installing

the rst projector (Set A) ................ 8

Removing pocket caps ........................ 8

Preparing elevator feet ........................ 8

Deciding installation position ............... 8

Setting up Set A................................... 9

2.3 Installing

the second projector (Set B) ........ 11

Stacking the projectors ...................... 11

Connecting projectors........................ 11

Setting up Set B................................. 12

2.4 Conrming Main

and Sub settings............................ 14

2.5 Fine adjusting

image position ............................... 15

For Intellectual Stack users ............... 15

For Simple Stack users...................... 16

3. STACK menu settings ......17

3.1 Displaying STACK menu ............ 17

3.2 Selecting Main, Sub or off .......... 18

3.3 Selecting lamp operation mode.. 19

3.4 Selecting lamp switching mode .. 21

3.5 Selecting input source for Sub.... 22

3.6 Exiting Intellectual

Stack menu ................................... 23

STACK menu ..................................... 23

Dialog from STACK menu.................. 23

3.7 Important information

for Intellectual Stack ...................... 24

4. Connecting cables ...........27

4.1 Connecting an RS-232C cable... 27

4.2 Connecting signal cables............ 28

Inputting image from Main to Sub...... 28

Inputting image

to Sub and Main individually........... 28

5. Setting input ports

using menu.........................29

5.1 Preparing for menu operations... 29

5.2 Checking Main projector's

operating status............................. 29

5.3 Starting up Main projector .......... 30

5.4 Setting the menu ........................ 31

Inputting image from Main to Sub

- Computer signal ........................... 31

Inputting image from Main to Sub

- Video signal

(either component or video) ........... 32

Inputting image to

Sub and Main individually............... 32

6. Restrictions

on Schedule function ........34

7. Troubleshooting ...............36

Contents

LX41/LW41 User Manual - Instant Stack Guide 020-000509-01 Rev.1 (06-2012)

1.1 Entries and graphical symbols explanation

The following entries and graphical symbols are used for the manuals and the

product as follows, for safety purpose. Please know their meanings beforehand,

and heed them.

1.2 Important safety instruction

The followings are important instructions for safely using the product in Instant

Stack. First of all, read the following instructions and be sure to always follow

them when using Instant Stack of this product.

(continued on next page)

WARNING This entry warns of a risk of serious personal injury or even

death.

CAUTION This entry warns of a risk of personal injury or physical

damage.

NOTICE This entry notices of fear of causing trouble.

WARNING ► Take a special care not to fall the stacked projectors.

• When stacking two projectors, make sure the elevator feet and heel of the

upper projector are inserted into the corresponding pockets of the lower

projectors. (

)

• When using the Instant Stack function by piling up two projectors, you can

change the projection angle by adjusting the

elevator feet of the unit that is placed underneath.

(

) Exercise care to prevent the stacked projector

from falling off or tipping over while adjusting the

elevator feet.

• A maximum of two projectors can be stacked. Do

not stack three or more projectors.

• Do not install the projectors that are stacked using

the stack pockets, elevator feet and heel of this

projector at a place higher than a person's height.

• Do not install the projectors that are stacked using

the stack pockets, elevator feet and heel of this

projector on a ceiling.

• Do not touch the stacked projectors except when

instructions are given in this manual. Do not hit the

projectors with any type of object.

Pocket cap

Stack pocket

LOCK

Elevator feet

Heel

Cap storage

pocket

Lens

adjuster

door

Stack

pocket

1. Introduction

Instant Stack feature

Introduction

LX41/LW41 User Manual - Instant Stack Guide 020-000509-01 Rev.1 (06-2012)

1.2 Important safety instruction - For Instant Stack feature (continued)

NOTICE ► Instant Stack is a feature that allows you to stack two projectors

or arrange them side by side easily. Depending on the installation and

surrounding environment, images projected from the two projectors may not

superimpose well enough. The images cannot superimpose well enough

especially when the screen is slanted, deformed or the surface is uneven.

• Images projected immediately after turning on the projectors are unstable due

to rising internal temperature. Wait for more than 20 minutes before starting

to adjust the superimposed images.

• The image positions may shift due to temperature change, vibration, or shock

caused by hitting the projector. Install the projectors in a stable environment

when using Instant Stack. If the image positions are shifted, readjust the

images. (

9, 12, 15

)

• The image positions may shift over time due to the tension and the weight of

the connecting cables. Make sure not to impose any load on the projectors

when arranging the cables.

• If the volume level of the built-in speakers is too high, the two projectors may

resonate, noise may occur and the image quality may deteriorate. In this

case, check the volume setting on both projectors. Lower the volume until the

symptoms disappear or arrange the projectors side by side.

• When two projectors are connected using the RS-232C cable, the Main

projector will be able to control the Sub projector. This feature is known as

Intellectual Stack. (

) When Intellectual Stack by means of RS-232C

feature is used, RS-232C communication cannot be used to control the

projector. If you wish to control the projectors, use the LAN connection that is

connected to any of the projectors.

• When Intellectual Stack is used, the operations or settings of some functions

are restricted. Refer to this manual for details. (

)

WARNING ► When removing the pocket caps from the stack pockets, be

sure to store them securely and safely inside the lens adjuster door to prevent

children and pets from swallowing the caps. (

) If swallowed, consult a

physician immediately.

CAUTION ► Be careful not to injure your nail and nger when removing

the pocket caps. (

)

Introduction

LX41/LW41 User Manual - Instant Stack Guide 020-000509-01 Rev.1 (06-2012)

General installation

NOTICE ► Position the projector to prevent light from directly hitting the

projector’s remote sensor.

• Do not place the product in a place where radio interference may be caused.

CAUTION ► Place the projector in a cool place with sufcient ventilation.

• Keep a space of 30 cm or more between a side of the projector and other

objects such as a wall. If you install two projectors in Style 2 (

), keep a

space of 30 cm or more between the two projectors.

• Do not stop up, block nor cover the projector’s vent holes.

• Do not place the projector at places that are exposed to magnetic elds, doing

so can cause the cooling fans inside the projector to malfunction.

► Avoid placing the projector in smoky, humid or dusty place.

• Do not place the projector near humidiers. Especially for an ultrasonic

humidier, chlorine and minerals contained in tap water are atomized and

could be deposited in the projector causing image degradation or other

problems.

WARNING ► Install the projector where you can access the power outlet

easily.

► Do not subject the projector to unstable conditions. Install the projector in a

stable horizontal position.

• Do not use any mounting accessories except the accessories specied by the

manufacturer. Read and keep the manuals of the accessories used.

• For special installation such as ceiling mounting, be sure to consult your

dealer beforehand. Specic mounting accessories and services may be

required.

► Do not install the projector near thermally conductive or ammable things.

► Do not place the projector where any oils, such as cooking or machine oil,

are used.

► Do not place the projector in a place where it may get wet.

Introduction

LX41/LW41 User Manual - Instant Stack Guide 020-000509-01 Rev.1 (06-2012)

Tentative terms for the two projectors

For better understanding of the descriptions in this

manual, the following terms are used when explain-

ing the vertical stacking installation.

Set A : Projector placed underneath

Set B : Projector placed on top of Set ASet A

Set B

Installation styles

Following are two styles to install the projectors. Instant Stack supports both

styles.

Style 1: Stack vertically

Style 2 : Arrange side by side

The descriptions in this manual are mainly on Style 1installation. If you wish to

install two projectors in Style 2, refer to the descriptions required in this manual.

1.3 Basic information and preparations

Instant Stack

Instant Stack is a feature that allows you to superimpose images projected from

two projectors easily. This projector is designed to provide this feature, with func-

tions to install two projectors and superimpose the images.

Intellectual Stack and Simple Stack

Instant Stack includes the following two features.

When two projectors are connected via an RS-232C cable with necessary set-

tings performed on the projectors, these two projectors will automatically operate

in synchronization with each other according to the settings. This is known as

Intellectual Stack in this manual.

The two projectors operate individually without the RS-232C connection. This is

known as Simple Stack in this manual.

Remote control for Intellectual Stack and Simple Stack

For Intellectual Stack, one projector is set as Main and the other is set as Sub.

(

) Only the Main projector is capable of receiving the remote control signals.

To operate the Sub projector, you need to point the remote control at the Main

projector.

For Simple Stack, both projectors can receive the remote control signals. To

avoid crosstalk when operating with the remote control, it is recommended to

operate one projector with the remote control and the other with the control panel

on the projector or a wired remote control. In this case, disable the remote control

receiving on the other projector with the KEY LOCK feature. (Operating Guide

→ OPTION menu)

LX41/LW41 User Manual - Instant Stack Guide 020-000509-01 Rev.1 (06-2012)

For safety reasons, read 1.2 Important safety instruction (

3~5

) carefully before

installation. In addition, take note of the followings for proper use of Instant Stack.

● When using Intellectual Stack, both projectors will respond to the remote control

signals until STACK MODE on either projector is set to SUB.

During installation, it is recommended to operate one projector with the remote

control and the other with the control panel on the projector or a wired remote

control. In this case, disable the remote control receiving on the other projector

with the KEY LOCK feature. (Operating Guide → OPTION menu)

●Images from Set Aand Set B may superimpose well but the image positions

can shift over time.

Readjust to superimpose the images.

●If the volume level of the built-in speakers is too high, the two projectors may

resonate, noise may occur and the image quality may deteriorate.

In this case, check the volume setting on both projectors. Lower the volume

until the symptoms disappear or arrange the projectors side by side. If the

image positions are shifted, readjust.

2.1 Preparing for Intellectual Stack

When using Intellectual Stack via RS-232C connection, ensure the following set-

tings are set on the two projectors. Otherwise, the Intellectual Stack menu cannot

be operated.

●STANDBY MODE in SETUP menu: NORMAL

(Operating Guide → SETUP menu)

●COMMUNICATION TYPE under COMMUNICATION in SERVICE menu: OFF

(Operating Guide → OPTION menu)

●STACK LOCK in SECURITY menu: OFF

When STACK LOCK is set to on, menus related to Instant Stack cannot be

operated. It is therefore necessary to set it to off during installation and menu

setting.

(1) Use the ▲/▼/◄/► buttons to go into the following menu.

ADVANCED MENU > SECURITY

> STACK LOCK

STACK LOCK dialog will appear on screen. (Operating

Guide → SECURITY menu)

(2) Use the ▲/▼ buttons to highlight OFF, and press the ► button to complete

the setting.

2. Installation

Installation

LX41/LW41 User Manual - Instant Stack Guide 020-000509-01 Rev.1 (06-2012)

NOTE • Set the tilt angle of Set A to within 12 degrees from the level line.

• Take the followings into account when considering the installation position.

- VERTICAL adjuster should be set to the upper limit position.

- ZOOM ring should not be set to the widest position.

- HORIZONTAL adjuster is recommended to be set near the center position.

Preparing elevator feet

When stacking the two projectors, set the length of the

elevator feet to the minimum using the elevator but-

tons on Set Aand B.

CAUTION ► Be careful when stacking the two

projectors, the projector on top may slide down.

NOTE • Cap storage pockets for the pocket caps

are inside the lens adjuster door. Be sure to keep

the caps in the storage pockets after removing the

caps from the stack pockets.

To store the cap to the pocket, place the thin end of

the cap into the pocket  rst, then push the other side

of the cap down  rmly to the bottom of the pocket.

It is important to ensure that the caps are securely

stored to prevent children and pets from swallowing

them.

LOCK

Thin end

Cap storage

pocket

Pocket caps

CAUTION ►It is recommended to use a pin or

the like to remove the caps. If you are using  nger,

be careful not to injure your nail and  nger.

Removing pocket caps

When stacking the two projectors, remove the pocket

caps on Set A.

Deciding installation position

Decide the position of Set Aand its projection angle. (Setup Guide →

Arrangement and Adjusting the projector’s elevator)

2.2 Installing the  rst projector (Set A)

Andere Handbücher für Vivid LX41

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Christie Projektor Handbücher

Christie

Christie Solaria One Bedienungsanleitung

Christie

Christie Mirage S+3K Bedienungsanleitung

Christie

Christie Crimson Series Bedienungsanleitung

Christie

Christie Roadie 4K35 Bedienungsanleitung

Christie

Christie CP2306-RGBe Montageanleitung

Christie

Christie LX501 Bedienungsanleitung

Christie

Christie DWU1052 Bedienungsanleitung

Christie

Christie LX501 Bedienungsanleitung

Christie

Christie LW650 Bedienungsanleitung

Christie

Christie LX750 Bedienungsanleitung

Christie

Christie Mirage SST Gebrauchs- und Pflegehandbuch

Christie

Christie 38-MX3001-01 Bedienungsanleitung

Christie

Christie Roadie HD+30K Bedienungsanleitung

Christie

Christie CP2000 Bedienungsanleitung

Christie

Christie CP2000-M Bedienungsanleitung

Christie

Christie DS30 Bedienungsanleitung

Christie

Christie DS+650 Bedienungsanleitung

Christie

Christie APS Series Gebrauchs- und Pflegehandbuch

Christie

Christie CP2000-ZX Bedienungsanleitung

Christie

Christie LX501 Bedienungsanleitung

Christie

Christie D4KLH60 Mirage 4KLH Bedienungsanleitung

Christie

Christie Mirage 304K Bedienungsanleitung

Christie

Christie CP2215 Bedienungsanleitung

Christie

Christie D13HD2-HS Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung