CINCH ModICE SE Series Bedienungsanleitung
ModICE™ SE/LE
Enclosure Assembly Instructions
Assembly and Opening Tools
2
© 2011 Cinch Connectors V2 10-2011
Introduction
This instruction manual applies to both the ModICE™ SE and LE enclosure systems.
• Small Enclosure : SE 18, 30 and 48 I/O
• Large Enclosure : LE 30, 48 and 60 I/O
• Blank Headers are also available for specic customer applications
Available options:
• Header with ferrite lter
• Enclosure with 1 or 2 heat sinks
• Enclosure with breather membrane
NOTE: The heat sink feature requires additional steps in the assembly of the printed circuit board.
Header
Enclosure
Ferrite lter (optional) Heat Sink (optional) Spring Plate for Heat Sink (optional)
For technical or ordering information on Transportation products,
contact Cinch at 630-705-6000 or visit our website at
www.cinch.com
3
© 2011 Cinch Connectors V2 10-2011
Printed Circuit Board Assembly
Protect the Header functional areas from conformal coating.
Ferrites must be immobilized by using conformal coating or
a bead of epoxy.
Secure Header onto the board
Headers must be secured to the board with 2 screws
• Use two, #4 self-tapping screws
• Torque: 2-3 in-lbs (0.23-0.34 Nm)
Refer to the Cinch Header drawings for board layout,
keep out areas and component height restrictions
4
© 2011 Cinch Connectors V2 10-2011
Heat Sink Option
Mosfet TO220
Press t spring plates into board
Slots (2) for Spring Plate press t
R
L
• Refer to Cinch header prints for specic
board layout and spring plate selection.
Install heat sink spring plates
• Install the spring plates after the printed circuit
board has been processed.
• Spring plates are marked “R” and “L” and must
be installed as indicated.
• When using a one (1) heat sink, use spring plate
“R” only.
• Spring plates and thermally conductive adhesive
paste are necessary to guarantee proper heat
conduction through the heat sinks;
Cinch recommends Loctite 383.
5
© 2011 Cinch Connectors V2 10-2011
ModICE™ Assembly Tool
Adjustable Header Holder
(SE position shown)
Adjustable Enclosure Holder
Header Alignment Blocks Down
(SE position shown)
Enclosure Holder in SE position
Header Alignment Blocks Up
(LE position shown)
Enclosure Holder in LE Position
• Tool p/n 5991111650
• The assembly tool is common to the ModICE SE and
LE Enclosures
• Simple settings to convert from the SE to the LE size
6
© 2011 Cinch Connectors V2 10-2011
ModICE™ Assembly Tool
SE
SE
Enclosure Holder Settings Header Holder Settings
Move Enclosure Holder to the back for the LE position For LE setting, lift up the two alignment blocks
LE LE
Tool Settings for Small (SE) and Large (LE) Enclosure
7
© 2011 Cinch Connectors V2 10-2011
Load Header into the holder
• Open the press to load the Header/PCB
assembly
• Alignment blocks must be in the down position
for SE headers (pic. shown)
• Alignment blocks must be in the up position
for LE headers (see previous page)
• Slide/Push the Header/PCB into the holder
(snap t retention by spring plunges)
Load Enclosure into the holder
• Check SE / LE position on the
previous page
1
2
1
Push for
snap t
Alignment Block
Spring plunge
12
ModICE™ Assembly
NOTE: Check gasket for proper alignment
before assembly. Gasket should not be
twisted or dislodged from corners during
handling.
8
© 2011 Cinch Connectors V2 10-2011
Close the assembly tool
• Push lever to assemble
• Header/PCB into the Enclosure
• Push all the way down to close
the enclosure (audible snaps)
Open the assembly tool
• Hold the enclosure down while
releasing the lever
ModICE™ Assembly
3
4
3
4
9
© 2011 Cinch Connectors V2 10-2011
Final inspection
• Even if using the Cinch Assembly tool
• 100% visual inspection is required to verify proper
engagement of all the locking tabs
• Manual engagement of the minitabs may be necessary to
complete the assembly. Press the Enclosure over the Header
so that all minitabs are engaged
Mini locking tabs
x6 SE Enclosure
x10 LE Enclosure
Tab Engaged Tab Not Engaged
ModICE™ Assembly
5
5
10
© 2011 Cinch Connectors V2 10-2011
ModICE™ is designed to be tamper proof.
Specic tools are required to open the enclosures.
Any attempt to open an enclosure without the recommended
tools may result in damaged parts that will affect the
mechanical characteristics and the sealing of the enclosure.
ModICE™ Opening Tool • Tool p/n 5991111611 – ModICE SE
• Tool p/n 5991111612 – ModICE LE
Andere Handbücher für ModICE SE Series
1
Dieses Handbuch passt für folgende Modelle
9
Inhaltsverzeichnis
Andere CINCH Gehäuse Handbücher
