Cisco Telepresence MX800 Bedienungsanleitung

Installation guide

for Cisco TelePresence MX800 Single

mounted on the wall

Installation guide for Cisco TelePresence MX800 Single - Wall mount

Dimensions

Height: 1258mm / 49.6in.

Width: 1596mm / 62.9in.

Depth: 148 mm / 5.9in.

Weight: 109kg /113kg (single camera / dual camera)

241 lb / 249 lb (single camera / dual camera)

Room setup

Explore the Cisco Project Workplace to find

inspiration and guidelines when preparing your

office or meeting room for video conferencing,

http://www.cisco.com/go/projectworkplace

User documentation

The user documentation for this product,

including compliance and safety information,

can be found on the Cisco website,

http://www.cisco.com/go/mx-docs

This guide covers wall-mounted MX800 Single with two camera options.

The instructions in this guide apply to systems with single and dual

camera, even if the illustrations show only the single camera option.

MX800 Single

with single camera

MX800 Single

with dual camera

Installation guide for Cisco TelePresence MX800 Single - Wall mount

Screws and tools.

Boxes are labeled A to H.

This guide refers to the labels.

A H

...

B+E-G Shows which boxes are inside.

1Open the plastic snap locks and remove

the side walls.

Packaging

Lift off box H. Lay box A flat on the floor

and remove the lid.

EMC Class A declaration

WARNING: This is a class A product. In a domestic environment

this product may cause radio interference in which case the user

may be required to take adequate measures.

声明

此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种

情况下，可能需要用户对其干扰采取切实可行的措施。

WARNING: This is a class A product. In a domestic environment

this product may cause radio interference in which case the user

may be required to take adequate measures.

Screws

The screw kit contains more screws than you need,

because the same kit is shipped with all mounting options.

M6x90, countersunk

Tool: Allen key, 4mm

M6x12, countersunk

Tool: Allen key, 4mm

Tools

Allen key, 4 mm

M6x100, pan

Tool: Allen key, 4mm

M6x12, pan

Tool: Allen key, 4mm

Installation guide for Cisco TelePresence MX800 Single - Wall mount

1Read before you start mounting

Safety information

Due to the size and mass of this product, it is important that

the wall-mounted system is safely installed according to these

installation instructions.

The wall and mounting hardware must be able to safely

support the product.

The wall-mounted system must be installed by qualified

personnel, in accordance with state and local building

regulations.

Manpower

We recommend four people working together to mount this

system. Follow local regulations.

Installation guide for Cisco TelePresence MX800 Single - Wall mount

2Mount wall bracket

Check that the wall bracket is level and mark the required

screw hole positions on the wall. Use at least four screws

when fastening the wall bracket. The wall bracket can be

fastened through any of the horizontal slots.

Fasten the wall bracket in a secure manner ensuring that the

wall’s structure is sufficient to support the system load (screws

and mounting hardware not provided; not shown in illustration).

The lower edge of the

screen image will be

at the height of these

horizontal slots.

We recommend that

the distance from

the floor to this line is

70cm / 27.6 in.*

*If you mount the system higher, note the following consequences:

- You may need to increase the distance between the video system and the

table in order for the camera to capture the closest participants.

- The camera will give an elevated view of the room. This view is not optimal

for video conferencing.

Further information: http://www.cisco.com/go/projectworkplace

2D CAD drawings with measurements:

http://www.cisco.com/go/mx-docs (Technical References)

Installation guide for Cisco TelePresence MX800 Single - Wall mount

3Mount spacers and top wall bracket

Snap the top wall bracket onto

the spacers. Face the narrow

slots against the wall.

Fasten the top wall bracket in a

secure manner ensuring that the

wall’s structure is sufficient to

support the system (screws and

mounting hardware not provided;

not shown in illustration).

Mount the left and right

spacer onto the wall bracket.

Fasten each spacer with two

screws (not provided; not

shown in illustration).

Installation guide for Cisco TelePresence MX800 Single - Wall mount

4Mount lower frame

A, B

Place the lower frame

onto the wall bracket.

Fasten the lower frame to the wall

bracket with two screws.

2 × M6x12, pan

Installation guide for Cisco TelePresence MX800 Single - Wall mount

5Fasten clamp on monitor

A, D

While the monitor is still in the package,

mount the clamp on the rear side.

Use the Allen key 2.5mm

and loosen, but do not

remove, the premounted

screws.

Push the support bracket

tight against the back plate

of the monitor.

Tighten the screws and

check that the clamp is

properly fastened.

Slide the clamp in place on

the monitor and make sure

that all the small clamps are

properly fitted.

Installation guide for Cisco TelePresence MX800 Single - Wall mount

Read before you mount the monitors

The monitor is heavy

We recommend four people working

together to mount the monitor. Two

people should lift the monitor using

the handles as described here. The

other people must help stabilizing the

monitor and check that the monitor

enters the slots properly.

90 kg / 200 lb

Use lifting handles

To avoid trapping your fingers, use the lifting

handles at the bottom of the monitor.

When you lift and place the monitor onto the

wall brackets, keep the monitor close to the

wall so the clamps on the rear side of the

monitor slide fully onto the top wall bracket.

The screws with wing nut, which you can see

from the sides of the monitor, must enter the

center slot on each side of the lower frame.

Installation guide for Cisco TelePresence MX800 Single - Wall mount

6Lift and place monitor onto lower frame

The screws with wing nut, which you can see

from the sides of the monitor, must enter the

center slot on each side of the lower frame.

Do not let go of the monitor before it is

securely placed on the lower frame.

Tighten the wing nuts on both sides.

They are accessed from the sides

of the monitor.

Rear view

Front view

Andere Handbücher für Telepresence MX800

Inhaltsverzeichnis

Andere Cisco Konferenzsystem Handbücher

Cisco

Cisco Profile Series Bedienungsanleitung

Cisco

Cisco Telepresence MX800 Leitfaden

Cisco

Cisco Webex Room Kit Plus Bedienungsanleitung

Cisco

Cisco Webex Share Bedienungsanleitung

Cisco

Cisco TelePresence SX20 Service-Handbuch

Cisco

Cisco MX300 G2 Bedienungsanleitung

Cisco

Cisco TelePresence System Codec C90 Bedienungsanleitung

Cisco

Cisco MX Series Bedienungsanleitung

Cisco

Cisco SX80 Bedienungsanleitung

Cisco

Cisco TANDBERG Edge MXP Montageanleitung

Cisco

Cisco TelePresence DX80 Bedienungsanleitung

Cisco

Cisco 7937G - Unified IP Conference Station VoIP... Bedienungsanleitung

Cisco

Cisco TelePresence System Codec C40 Service-Handbuch

Cisco

Cisco TelePresence SX10 Service-Handbuch

Cisco

Cisco TelePresence SX10 Bedienungsanleitung

Cisco

Cisco TelePresence Touch 10 Bedienungsanleitung

Cisco

Cisco MX300 G2 Bedienungsanleitung

Cisco

Cisco TelePresence SX20 Bedienungsanleitung

Cisco

Cisco TelePresence DX70 Service-Handbuch

Cisco

Cisco Webex Room Kit Plus Precision 60 Bedienungsanleitung

Cisco

Cisco DX600 series Bedienungsanleitung

Cisco

Cisco TelePresence Profile 55 Bedienungsanleitung

Cisco

Cisco TelePresence DX70 Bedienungsanleitung

Cisco

Cisco EX90 Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Inmarsat

Inmarsat mini M Bedienungsanleitung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung