Cisco GS7000 Betriebsanleitung

4022871 Rev C

Model GS7000 GainMaker Node

Seg2Way Status Monitor/Local

Control Module

Installation and Operation Guide

For Your Safety

ExplanationofWarning andCaution Icons

Avoid personal injury and product damage! Do not proceed beyond any symbol

until you fully understand the indicated conditions.

The following warning and caution icons alert you to important information about

the safe operation of this product:

You may find this symbol in the document that accompanies this product.

This symbol indicates important operating or maintenance instructions.

You may find this symbol affixed to the product. This symbol indicates a live

terminal where a dangerous voltage may be present; the tip of the flash points

to the terminal device.

You may find this symbol affixed to the product. This symbol indicates a

protective ground terminal.

You may find this symbol affixed to the product. This symbol indicates a

chassis terminal (normally used for equipotential bonding).

You may find this symbol affixed to the product. This symbol warns of a

potentially hot surface.

You may find this symbol affixed to the product and in this document. This

symbol indicates an infrared laser that transmits intensity-modulated light

and emits invisible laser radiation or an LED that transmits intensity-

modulated light.

Important

Please read this entire guide. If this guide provides installation or operation

instructions, give particular attention to all safety statements included in this guide.

Notices

TrademarkAcknowledgments

Cisco, Cisco Systems, the Cisco logo, the Cisco Systems logo, Scientific Atlanta,

the Scientific Atlanta logo, GainMaker, SciCare, and bdr are registered

trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S.

and certain other countries.

All other trademarks mentioned in this document are the property of their respective

owners.

PublicationDisclaimer

Cisco Systems, Inc. assumes no responsibility for errors or omissions that may

appear in this publication. We reserve the right to change this publication at any

time without notice. This document is not to be construed as conferring by

implication, estoppel, or otherwise any license or right under any copyright or

patent, whether or not the use of any information in this document employs an

invention claimed in any existing or later issued patent.

Information in this publication is subject to change without notice. No part of this

publication may be reproduced or transmitted in any form, by photocopy,

microfilm, xerography, or any other means, or incorporated into any information

retrieval system, electronic or mechanical, for any purpose, without the express

permission of Cisco Systems, Inc.

4022871 Rev C iii

Contents

Important Safety Instructions v

Chapter 1 Overview 1

Model GS7000 Node Description ..........................................................................................2

Overview......................................................................................................................2

Physical Description...................................................................................................2

Functional Description...............................................................................................4

Status Monitor/Local Control Module Description ...........................................................6

Overview......................................................................................................................6

Local Control Module Description...........................................................................6

Status Monitor Description .......................................................................................7

Status Monitor/Local Control Module Diagram ...................................................8

Chapter 2 Installation 11

Installing the SM/LCM.........................................................................................................12

Overview....................................................................................................................12

Opening the Housing............................................................................................... 12

Installing the Module ...............................................................................................12

Closing the Housing.................................................................................................15

Chapter 3 Configuration 17

Local Control Module Configuration Procedure ..............................................................18

Introduction...............................................................................................................18

LCM Configuration Parameters .............................................................................18

Configuring the LCM...............................................................................................22

Status Monitor Configuration Procedure...........................................................................26

Introduction...............................................................................................................26

Configuring the SM in CheetahNet........................................................................ 26

Verifying Status Monitor Configuration Locally .................................................29

Chapter 4 Troubleshooting 33

SM/LCM Sensors and Indicators........................................................................................34

Local Control Module Troubleshooting ............................................................................. 35

Introduction...............................................................................................................35

Green COND LED not Blinking .............................................................................35

Red STATUS LED Blinking Slowly........................................................................35

Red STATUS LED Flashing Fast.............................................................................36

Contents

iv 4022871

Rev

Red STATUS LED On Solid.....................................................................................37

Chapter 5 Customer Support Information 39

Obtaining Product Support..................................................................................................40

Support Telephone Numbers..................................................................................40

Return Product for Repair ....................................................................................................42

Obtaining an RMA Number and Shipping Address...........................................42

Completing the Scientific Atlanta Transmission Networks Repair Tag...........43

Packing and Shipping the Product.........................................................................46

Glossary 49

Index 55

Important Safety Instructions

4022871 Rev C v

Important Safety Instructions

Read and Retain Instructions

Carefully read all safety and operating instructions before operating this equipment,

and retain them for future reference.

FollowInstructions and HeedWarnings

Follow all operating and use instructions. Pay attention to all warnings and cautions

in the operating instructions, as well as those that are affixed to this equipment.

Terminology

The terms defined below are used in this document. The definitions given are based

on those found in safety standards.

Service Personnel - The term service personnel applies to trained and qualified

individuals who are allowed to install, replace, or service electrical equipment. The

service personnel are expected to use their experience and technical skills to avoid

possible injury to themselves and others due to hazards that exist in service and

restricted access areas.

User and Operator - The terms user and operator apply to persons other than service

personnel.

Ground(ing) and Earth(ing) - The terms ground(ing) and earth(ing) are synonymous.

This document uses ground(ing) for clarity, but it can be interpreted as having the

same meaning as earth(ing).

ElectricShock Hazard

This equipment meets applicable safety standards.

WARNING:

To reduce risk of electric shock, perform only the instructions that are

included in the operating instructions. Refer all servicing to qualified service

personnel only.

Electric shock can cause personal injury or even death. Avoid direct contact with

dangerous voltages at all times.

Know the following safety warnings and guidelines:

Only qualified service personnel are allowed to perform equipment installation

or replacement.

Important Safety Instructions

vi 4022871

Rev

Only qualified service personnel are allowed to remove chassis covers and access

any of the components inside the chassis.

EquipmentPlacement

WARNING:

Avoid personal injury and damage to this equipment. An unstable mounting

surface may cause this equipment to fall.

To protect against equipment damage or injury to personnel, comply with the

following:

Install this equipment in a restricted access location (access restricted to service

personnel).

Make sure the mounting surface or rack is stable and can support the size and

weight of this equipment.

Strand(Aerial) Installation

CAUTION:

Be aware of the size and weight of strand-mounted equipment during the

installation operation.

Ensure that the strand can safely support the equipment’s weight.

Pedestal, Service Closet, EquipmentRoom orUndergroundVaultInstallation

WARNING:

Avoid the possibility of personal injury. Ensure proper handling/lifting

techniques are employed when working in confined spaces with heavy

equipment.

Ensure this equipment is securely fastened to the mounting surface or rack

where necessary to protect against damage due to any disturbance and

subsequent fall.

Ensure the mounting surface or rack is appropriately anchored according to

manufacturer’s specifications.

Ensure the installation site meets the ventilation requirements given in the

equipment’s data sheet to avoid the possibility of equipment overheating.

Ensure the installation site and operating environment is compatible with the

equipment’s International Protection (IP) rating specified in the equipment’s data

sheet.

Important Safety Instructions

4022871 Rev C vii

Connectingto UtilityACPower

Important: If this equipment is a Class I equipment, it must be grounded.

If this equipment plugs into an outlet, the outlet must be near this equipment,

and must be easily accessible.

Connect this equipment only to the power sources that are identified on the

equipment-rating label, which is normally located close to the power inlet

connector(s).

This equipment may have two power sources. Be sure to disconnect all power

sources before working on this equipment.

If this equipment does not have a main power switch, the power cord connector

serves as the disconnect device.

Always pull on the plug or the connector to disconnect a cable. Never pull on the

cable itself.

Connectionto NetworkPower Sources

Refer to this equipment’s specific installation instructions in this manual or in

companion manuals in this series for connection to network ferro-resonant AC

power sources.

ACPower Shunts

AC power shunts may be provided with this equipment.

Important: The power shunts (where provided) must be removed before installing

modules into a powered housing. With the shunts removed, power surge to the

components and RF-connectors is reduced.

CAUTION:

RF connectors and housing seizure assemblies can be damaged if shunts are

not removed from the equipment before installing or removing modules from

the housing.

Grounding (UtilityAC Powered Equipment inPedestals, ServiceClosets, etc.)

This section provides instructions for verifying that the equipment is properly

grounded.

Safety Plugs (USA Only)

This equipment is equipped with either a 3-terminal (grounding-type) safety plug or

a 2-terminal (polarized) safety plug. The wide blade or the third terminal is provided

for safety. Do not defeat the safety purpose of the grounding-type or polarized

safety plug.

Important Safety Instructions

viii 4022871

Rev

To properly ground this equipment, follow these safety guidelines:

Grounding-Type Plug - For a 3-terminal plug (one terminal on this plug is a

protective grounding pin), insert the plug into a grounded mains, 3-terminal

outlet.

Note: This plug fits only one way. If this plug cannot be fully inserted into the

outlet, contact an electrician to replace the obsolete 3-terminal outlet.

Polarized Plug - For a 2-terminal plug (a polarized plug with one wide blade

and one narrow blade), insert the plug into a polarized mains, 2-terminal outlet

in which one socket is wider than the other.

Note: If this plug cannot be fully inserted into the outlet, try reversing the plug.

If the plug still fails to fit, contact an electrician to replace the obsolete 2-terminal

outlet.

Grounding Terminal

If this equipment is equipped with an external grounding terminal, attach one end of

an 18-gauge wire (or larger) to the grounding terminal; then, attach the other end of

the wire to a ground, such as a grounded equipment rack.

Safety Plugs (European Union)

Class I Mains Powered Equipment – Provided with a 3-terminal AC inlet and

requires connection to a 3-terminal mains supply outlet via a 3-terminal power

cord for proper connection to the protective ground.

Note: The equipotential bonding terminal provided on some equipment is not

designed to function as a protective ground connection.

Class II Mains Powered Equipment – Provided with a 2-terminal AC inlet that

may be connected by a 2-terminal power cord to the mains supply outlet. No

connection to the protective ground is required as this class of equipment is

provided with double or reinforced and/or supplementary insulation in

addition to the basic insulation provided in Class I equipment.

Note: Class II equipment, which is subject to EN 50083-1, is provided with a

chassis mounted equipotential bonding terminal. See the section titled

Equipotential Bonding for connection instructions.

EquipotentialBonding

If this equipment is equipped with an external chassis terminal marked with the IEC

60417-5020 chassis icon ( ), the installer should refer to CENELEC standard EN

50083-1 or IEC standard IEC 60728-11 for correct equipotential bonding connection

instructions.

Andere Handbücher für GS7000

Inhaltsverzeichnis

Andere Cisco Steuereinheit Handbücher

Cisco

Cisco HPNA Bedienungsanleitung

Cisco

Cisco ASA5506-AP702 Bedienungsanleitung

Cisco

Cisco LightStream 1010 Kurzanleitung

Cisco

Cisco Firepower 4112 Handbuch

Cisco

Cisco NM-1CT1 Kurzanleitung

Cisco

Cisco PA-4T+ Bedienungs- und Wartungsanleitung

Cisco

Cisco ATUC-4DMT-ISDN Bedienungs- und Wartungsanleitung

Cisco

Cisco C3850-NM-4-1G Bedienungsanleitung

Cisco

Cisco SM-X-1T3/E3 Bedienungsanleitung

Cisco

Cisco CSS 11500 Service-Handbuch

Cisco

Cisco EHWIC-3G-EVDO Bedienungsanleitung

Cisco

Cisco Catalyst WS-X3001 Bedienerhandbuch

Cisco

Cisco 3110 Bedienungsanleitung

Cisco

Cisco GS7000 Bedienerhandbuch

Cisco

Cisco CGM-WPAN-OFDM-FCC Bedienungsanleitung

Cisco

Cisco WS-G5484 Bedienungsanleitung

Cisco

Cisco ONS 15200 Bedienungsanleitung

Cisco

Cisco Catalyst 3110G Handbuch

Cisco

Cisco WS-SVC-ASA-SM1-K7 Installations- und Betriebshandbuch

Cisco

Cisco Beacon Point Module Handbuch

Cisco

Cisco MEM-NP8F Series Kurzanleitung

Cisco

Cisco PA-VXA Series Bedienungs- und Wartungsanleitung

Cisco

Cisco 6015 Gebrauchs- und Pflegehandbuch

Cisco

Cisco MEM-CIP-64M Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung