Cisco SM-X-1T3/E3 Bedienungsanleitung

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Connecting Cisco T3 and E3 Service Modules to

the Network

Last Updated: August 14, 2013

OL-27149-01

This guide describes how to install a Cisco SM-X-1T3/E3 service module and how to connect the service

module to your network.

Contents

This guide contains the following sections:

•About the Cisco SM-X-1T3/E3 Enhanced Service Module, page 2

•Conventions, page 2

•Safety Warnings, page 2

•Installing and Removing the Cisco SM-X-1T3/E3 on Second Generation Integrated Services

Routers, page 4

•Installing and Removing the Cisco SM-X-1T3/E3 on Cisco 4451-X Integrated Services Routers,

page 5

•Connecting Cisco SM-X-1T3/E3 Service Modules to the Network, page 7

•Cisco SM-X-1T3/E3 Service Module LEDs, page 9

•Additional References, page 11

Connecting Cisco T3 and E3 Service Modules to the Network

OL-27149-01

Connecting Cisco T3 and E3 Service Modules to the Network

About the Cisco SM-X-1T3/E3 Enhanced Service Module

The Cisco SM-X-1T3/E3 is a single-port universal T3/E3 enhanced service module with integrated

CSU/DSU, clear channel, and subrate support. Channels on the service module can be configured as

either T3 or E3 using Cisco IOS software.

Figure 1 Cisco SM-X-1T3/E3 Enhanced Service Module Faceplate

Conventions

Note Means reader take note. Notes contain helpful suggestions or references to additional information and

material.

Caution This symbol means reader be careful. In this situation, you might do something that could result in

equipment damage or loss of data.

Tip Means the following information will help you solve a problem. The tips information might not be

troubleshooting or even an action, but could be useful information, similar to a Timesaver.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning statement to locate its translation in the translated safety warnings that accompanied

this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Safety Warnings

Warning

Read the installation instructions before connecting the system to the power source.

Statement 1004

SEE MANUAL BEFORE INSTALLING NETWORK MODULE

300923

SM-X-1T3/E3

LP AIS

RX TX

FERF/RAI

T3/E3

Connecting Cisco T3 and E3 Service Modules to the Network

OL-27149-01

Connecting Cisco T3 and E3 Service Modules to the Network

Safety Warnings

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260.

Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The

telecommunications lines must be disconnected 1) before unplugging the main power connector or 2)

while the housing is open, or both.

Statement 1043

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.

Statement 1

Warning

This unit might have more than one power supply connection. All connections must be removed to

de-energize the unit.

Statement 1028

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning

Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF

or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,

detach the end away from the unit first.

Statement 1026

Warning

Before opening the unit, disconnect the telephone-network cables to avoid contact with

telephone-network voltages.

Statement 1041

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings,

necklaces, and watches). Metal objects will heat up when connected to power and ground and can

cause serious burns or weld the metal object to the terminals.

Statement 43

Warning

Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry

tub, in a wet basement, or near a swimming pool.

Statement 1035

Warning

Never install telephone jacks in wet locations unless the jack is specifically designed for wet

locations.

Statement 1036

Connecting Cisco T3 and E3 Service Modules to the Network

OL-27149-01

Connecting Cisco T3 and E3 Service Modules to the Network

Installing and Removing the Cisco SM-X-1T3/E3 on Second Generation Integrated Services Routers

Warning

Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

Statement 1037

Warning

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote

risk of electric shock from lightning.

Statement 1038

Warning

To report a gas leak, do not use a telephone in the vicinity of the leak.

Statement 1039

Warning

There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with

the same or equivalent type recommended by the manufacturer. Dispose of used batteries according

to the manufacturer's instructions.

Statement 1015

Warning

Blank faceplates and cover panels serve three important functions: they prevent exposure to

hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)

that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not

operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement

1029

Warning

No user-serviceable parts inside. Do not open.

Statement 1073

Warning

For connections outside the building where the equipment is installed, the following ports must be

connected through an approved network termination unit with integral circuit protection.

T3, E3 Statement 1044

Installing and Removing the Cisco SM-X-1T3/E3 on Second

Generation Integrated Services Routers

For information on installing Cisco SM-X-1T3/E3 Enhanced Service Modules on Second Generation

Integrated Services Routers (ISR G2), see Installing Cisco Network Modules and Service Modules in

Cisco Access Routers.

To operate the Cisco SM-X-1T3/E3 module on Cisco ISR G2 routers, use one of the following

Cisco IOS releases:

•15.2(4)M4 or later

•15.3(1)T2 or later

•15.3(2)T1 later

Connecting Cisco T3 and E3 Service Modules to the Network

OL-27149-01

Connecting Cisco T3 and E3 Service Modules to the Network

Installing and Removing the Cisco SM-X-1T3/E3 on Cisco 4451-X Integrated Services Routers

Installing and Removing the Cisco SM-X-1T3/E3 on Cisco 4451-X

Integrated Services Routers

This section describes the following tasks for the Cisco SM-X-1T3/E3 enhanced service module:

•Software Requirements for the Cisco SM-X-1T3/E3, page 5

•Removing the Cisco SM-X-1T3/E3 from a Cisco ISR 4451-X Router, page 6

•Installing the Cisco SM-X-1T3/E3 in a Cisco ISR 4451-X Router, page 6

•Verifying Cisco SM-X-1T3/E3 Installation in a Cisco ISR 4451-X Router, page 6

Caution Always wear an electrostatic discharge (ESD)-preventive wrist strap and ensure that it makes good

contact with your skin when you remove or install a service module (SM). Connect the equipment end

of the wrist strap to the metal part of the chassis.

Caution Handle service modules (SMs) by the edges only. SMs are ESD-sensitive components and can be

damaged by mishandling.

Software Requirements for the Cisco SM-X-1T3/E3

Cisco IOS XE Release 3.9.1 or later release is required to operate the Cisco SM-X-1T3/E3 enhanced

service module on Cisco ISR 4451-X routers.

To determine the version of Cisco IOS software that is running on your router, log in to the router and

enter the show version command:

Router> show version

Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Experimental

Version 15.3(20130513:160617)

[v153_2_s_xe39_throttle-BLD-BLD_V153_2_S_XE39_THROTTLE_LATEST_20130513_144824-ios 170]

Compiled Mon 13-May-13 14:05 by mcpre

IOS XE Version: BLD_V153_2_S

Connecting Cisco T3 and E3 Service Modules to the Network

OL-27149-01

Connecting Cisco T3 and E3 Service Modules to the Network

Installing and Removing the Cisco SM-X-1T3/E3 on Cisco 4451-X Integrated Services Routers

Removing the Cisco SM-X-1T3/E3 from a Cisco ISR 4451-X Router

Use the following procedure to remove the Cisco SM-X-1T3/E3 from a Cisco ISR 4451-X Router:

Step 1 Read the “Safety Warnings” section on page -2 before you perform any module replacement.

Step 2 Locate the service module (SM) to be removed.

Step 3 Using a number 1 Phillips or flat-blade screwdriver, unscrew the captive mounting screws on the module

faceplate. See Figure 1.

Step 4 Pull the Cisco SM-X-1T3/E3 out of the chassis.

Step 5 Place the SM in an antistatic bag to protect it from electrostatic discharge (ESD) damage.

Installing the Cisco SM-X-1T3/E3 in a Cisco ISR 4451-X Router

Use the following procedure to install the Cisco SM-X-1T3/E3 on a Cisco ISR 4451-X Router:

Step 1 Read the “Safety Warnings” section on page -2 before you perform any module replacement.

Step 2 Remove the blank faceplates installed over the slot you intend to use.

Step 3 Push the Cisco SM-X-1T3/E3 into place until you feel the edge connector seat securely into the

connector on the router backplane. The module faceplate should contact the chassis rear panel.

Step 4 Using a number 1 Phillips or flat-blade screwdriver, tighten the captive mounting screws on the module

faceplate. See Figure 1.

Verifying Cisco SM-X-1T3/E3 Installation in a Cisco ISR 4451-X Router

Use the show diag command to verify that the Cisco SM-X-1T3/E3 has been installed correctly. In the

following example, one service module is recognized by the system.

router#show diag ?

all All related information

chassis Chassis related information

slot Slot location information for this command

subslot Subslot location information for this command

Router#show diag subslot 2/0 eeprom detail

Connecting Cisco T3 and E3 Service Modules to the Network

OL-27149-01

Connecting Cisco T3 and E3 Service Modules to the Network

Connecting Cisco SM-X-1T3/E3 Service Modules to the Network

SPA EEPROM data for subslot 2/0:

EEPROM version : 4

Compatible Type : 0xFF

Controller Type : 1909

Hardware Revision : 1.0

PCB Part Number : 73-14154-02

Top Assy. Part Number : 800-36532-01

Board Revision : 06

Deviation Number : 123598

Fab Version : 02

PCB Serial Number : FOC15495HU1

Asset ID : REV 2F

Product Identifier (PID) : SM-X-1T3/E3

Version Identifier (VID) : V01

CLEI Code : TBD

Base MAC Address : C4 0A CB 56 00 99

MAC Address block size : 3

Manufacturing Test Data : 00 00 00 00 00 00 00 00

Environment Monitor Data : 40 0B E3 43 00 0A

Platform features : 02 01 01 0A 00 00 00 00

01 01 00

Connecting Cisco SM-X-1T3/E3 Service Modules to the Network

To connect a Cisco SM-X-1T3/E3 enhanced service module to the network, use a 75-ohm 728-A coaxial

cable to connect the BNC connector on the service module to a networking device (see Figure 2).

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

No user-serviceable parts inside. Do not open.

Statement 1073

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Warning

Read the installation instructions before connecting the system to the power source.

Statement 1004

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable grounding is available.

Statement 1024

Connecting Cisco T3 and E3 Service Modules to the Network

OL-27149-01

Connecting Cisco T3 and E3 Service Modules to the Network

Connecting Cisco SM-X-1T3/E3 Service Modules to the Network

Warning

Blank faceplates and cover panels serve three important functions: they prevent exposure to

hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)

that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not

operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement

1029

Warning

For connections outside the building where the equipment is installed, the following ports must be

connected through an approved network termination unit with integral circuit protection. T3/E3

Statement 1044

Warning

To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety,

connect the SM-X-1T3/E3 interface ports only to intra-building or unexposed wiring or cable. The

intrabuilding cable must be shielded and the shield must be grounded at both ends. The intra-building

port(s) of the equipment or subassembly must not be metallically connected to interfaces that connect

to the OSP or its wiring. These interfaces are designed for use as intra-building interfaces only (Type

2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling.

The addition of Primary Protectors is not sufficient protection in order to connect these interfaces

metallically to OSP wiring.

Statement 7003

Caution To minimize transient surges, the internal wiring should not be routed in the same conduit with power

lines or external telephone lines.

Connecting Cisco T3 and E3 Service Modules to the Network

OL-27149-01

Connecting Cisco T3 and E3 Service Modules to the Network

Cisco SM-X-1T3/E3 Service Module LEDs

Figure 2 Connecting a T3/E3 Service Module to a Networking Device

Tip When connecting the Cisco SM-X-1T3/E3 service module to a port adapter used in another router series,

verify that you are connecting the TX port on the service module with the RX port on the port adapter,

and the TX port on the port adapter to the RX port on the service module.

Cisco SM-X-1T3/E3 Service Module LEDs

The Cisco SM-X-1T3/E3 enhanced service module includes several indicator LEDs. Figure 3 and

Table 1 describe the LEDs on the T3/E3 enhanced service module.

Figure 3 Cisco SM-X-1T3/E3 LEDs

SEE MANUAL BEFORE INSTALLING NETWORK MODULE

SM-X-1T3/E3

LP AIS

RX TX

FERF/RAI

T3/E3

300924

SUPERVISOR2

WS-X6K-SUP2-2GE

STATUS

SYSTEM

CONSOLE

PWR MGMT

RESET

CONSOLE

PORT

MODE

PCMCIA EJECT

PORT 1 PORT 2

Switch Load

100%

LINK

OSM-4OC12 POS-SI

4 PORT OC-12 POS SM IR

STATUS

4RESET

LINK

CARRIER

ALARM

CARRIER

ALARM

CARRIER

ALARM

CARRIER

ALARM

ACTIVE

PORT 1

ACTIVE

PORT 2

ACTIVE

PORT 3

ACTIVE

PORT4

OSM-4OC12 POS-SI

4 PORT OC-12 POS SM IR

STATUS

4RESET

LINK

CARRIER

ALARM

CARRIER

ALARM

CARRIER

ALARM

CARRIER

ALARM

ACTIVE

PORT 1

ACTIVE

PORT 2

ACTIVE

PORT 3

ACTIVE

PORT4

RX TX

300925

SEE MANUAL BEFORE INSTALLING NETWORK MODULE

SM-X-1T3/E3

LP AIS

RX TX

FERF/RAI

T3/E3

LED

FERF/RAI

LED

AIS

LED

Connecting Cisco T3 and E3 Service Modules to the Network

OL-27149-01

Connecting Cisco T3 and E3 Service Modules to the Network

Cisco SM-X-1T3/E3 Service Module LEDs

Table 1 Cisco SM-X-1T3/E3Service Module LEDs

LED Meaning

EN Green indicates that the service module has passed its self-test and is

available to the router.

AL Yellow indicates that the port is out of frame.

CD Green indicates that the signal is present on the port.

LP Yellow indicates that a loopback condition is present on the port.

AIS Yellow indicates an alarm on the DS3 transmission.

FERF/RAI Yellow indicates a remote failure at the far end of the connection.

Inhaltsverzeichnis

Andere Cisco Steuereinheit Handbücher

Cisco

Cisco MGX RPM-XF Bedienungsanleitung

Cisco

Cisco ONS 15540 ESPx Bedienungsanleitung

Cisco

Cisco Catalyst 9400 Series Installations- und Betriebshandbuch

Cisco

Cisco T1 Bedienungsanleitung

Cisco

Cisco ATUC-4DMT-ISDN Bedienungs- und Wartungsanleitung

Cisco

Cisco TelePresence Touch10 Bedienungsanleitung

Cisco

Cisco NCS 1010 Merkblatt

Cisco

Cisco ONS 15200 Bedienungsanleitung

Cisco

Cisco HPNA Bedienungsanleitung

Cisco

Cisco 3600 Series Kurzanleitung

Cisco

Cisco GS7000 Bedienerhandbuch

Cisco

Cisco ASA5506-AP702 Bedienungsanleitung

Cisco

Cisco CGM-WPAN-OFDM-FCC Bedienungsanleitung

Cisco

Cisco Catalyst 3110G Handbuch

Cisco

Cisco WS-G5484 Bedienungsanleitung

Cisco

Cisco PA-4T+ Bedienungs- und Wartungsanleitung

Cisco

Cisco NM-1E2W Kurzanleitung

Cisco

Cisco Catalyst 5000 Series Bedienungsanleitung

Cisco

Cisco TelePresence Touch10 Bedienungsanleitung

Cisco

Cisco WS-SVC-ASA-SM1-K7 Installations- und Betriebshandbuch

Cisco

Cisco MEM-CIP-64M Bedienungsanleitung

Cisco

Cisco T3 Kurzanleitung

Cisco

Cisco WS-SVC-WISM2-1-K9 Kurzanleitung

Cisco

Cisco GS7000 Betriebsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung