Cisco Meraki Z3 Bedienungsanleitung

Z3 Installation Guide [Internal]

This document describes how to install and set up the Z3 teleworker gateway. Additional reference documents are

available online at: www.meraki.com/library/products.

Z3 Overview

The Meraki Z3 is an enterprise teleworker gateway designed for telecommuting employees and IT staff. It is also a great

all-in-one device to test the capabilities of Meraki's cloud-managed networking. This gateway provides the following

features:

• Support for four LA connections

• Dual-concurrent 802.11ac radios for wireless connections

• Wall screws and anchors for mounting drywall surface, either vertically or horizontally

Package contents

In addition to the Z3, the following are provided.

The Z3 front panel

Ports and Status Indicators

The Z3 uses a single LED to inform the user of the device's status.

LED Status Meaning

Flashing white Operation in progress

Solid white Power is applied, Fully operational

The Z3 back panel

Additional functions on the back panel are described below, from left to right.

Reset button

Insert a paper clip if a reset is required.

• A brief, momentary press: To delete a downloaded

configuration and reboot.

• Press and hold for more than 10 sec: To force the

unit into a full factory reset.

LA ports

These 4 ports provide connectivity to computers,

printers, access points, or Ethernet switches.

A steady green LED indicates bidirectional connectivity,

and flashing green indicates traffic.

WA / Internet port Provides connectivity to the WA .

USB port USB 2.0 for 3G/4G wireless cards

Power input Designed for use only with the unit’s power supply.

The Z3 bottom panel

Please note that the serial number is located on the product label at the bottom panel of Z3

Mounting hardware

The supplied wall screws and anchors allow you to mount the gateway on a drywall surface, either vertically or

horizontally.

• For mounting on drywall, use a ¼-in drill bit, then insert the plastic and screw assemblies.

• For mounting on wood or a similar surface, use only the screws.

• Allow the heads of the screws to stick out far enough to be inserted securely into the back of the gateway.

Connecting to WA

All Meraki Z3 devices must have an IP address. This section describes how to configure your local area network before

you deploy it. A local management web service, running on the gateway, is accessed through a browser running on a

client PC. This web service is used for configuring and monitoring basic ISP/WA connectivity.

Setting up a static IP address

Do the following to configure basic connectivity and other networking parameters:

1. Using a client machine such as a laptop, connect to one of the four LAN ports of the Z3.

2. Using a browser on the client machine, access the gateway's built-in web service by browsing to

http://setup.meraki.com. (You do not have to be connected to the Internet to reach this address)

3. Click Uplink configuration under the Local status tab. The default credentials use the device serial number as

the username, with a blank password field.

4. Choose Static for the IP Assignment option.

5. Enter the IP address, subnet mask, default gateway IP and D S server information.

Setting up a DHCP IP address

By default all Z3 devices are configured to DHCP from upstream WA / ISP servers. Simply plug the Z3's WA /

Internet port to your upstream circuit and wait a few minutes for the unit to negotiate a DHCP address.

Additional settings

Setting VLANs

If your WA uplink is on a trunk port, choose VLAN tagging > Use VLAN tagging and enter the appropriate value for

VLAN ID for your network.

Setting PPPoE

PPPoE authentication may be required if you are connecting Z3 device to a DSL circuit. You need to know your

authentication option and credentials (supplied by your ISP) in order to complete these steps.

• Choose Connection Type > PPPoE.

• Select your Authentication option.

• If you select Use authentication, enter appropriate values for Username and Password.

Web proxy settings

These settings take effect if the Z3 device has to fall back to using HTTP to contact the Cloud Controller. By default, web

proxy is disabled. To enable web proxy, do the following:

To ensure that the client PC is redirected to the local web service in the following step, you must disable all

other network services (ex: wi-fi) on your client machine.

When the WA connection is fully enabled, the device's front LED will be solid white.

• Choose Web proxy > Yes.

• Enter values as appropriate for Hostname or IP and Port.

• If you require authentication, choose Authentication > Use authentication, and enter appropriate values for

Username and Password.

Configuring physical link settings

To configure physical link settings on the Ethernet ports, click Local status > Ethernet configuration. You can enable

half duplex, full duplex, and autonegotiation, as well as set 10- or 100-Mbps data rates.

Power efficiency modes

The Meraki Z3 Teleworker Appliance has an off mode and a networked standby or efficient idle mode, both with power

consumption less than 12W.

In off mode, the power consumption is a measured 0.3W. In the networked standby or efficient idle mode, the power

consumption is under that of full operation mode, which is a measured 6.6W. This mode is initiated after treating the last

payload packets.

To activate and/or deactivate wireless network ports, you may use the physical on/off switch or deactivate through the

Meraki Dashboard.

Regulatory

This equipment is for indoor use only and the PoE device is considered unlikely to connect to an Ethernet network with

outside plant routing, including campus environments.

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

FCC Interference Statement

To apply all configuration settings to the gateway, be sure to click Save Settings at the bottom of the page.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications no expressly approved by Meraki could void the user’s authority to operate this

equipment. This Transmitter must not be co-located or operation in conjunction with any other antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter

must not be co-located or operating in conjunction with any other antenna or transmitter.

IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.

If the device is going to be operated in the 5.15 - 5.25 frequency range, then it is restricted to indoor environment only.

This device meets all other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

Industry Canada Statement

This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Ce dispositif est conforme à la norme C R-247 d’Industrie Canada applicable aux appareils radio exempts de licence.

Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage

préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un

fonctionnement indésirable.

Industry Canada Caution

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful

interference to co-channel mobile satellite systems;

(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850

MHz and that these radars could cause interference and/or damage to LE-LA devices.

Avertissement:

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur

afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

(ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés

utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces

radars pourraient causer du brouillage et/ou des dommages aux dispositifs LA -EL.

Industry Canada Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 20 cm between the radiator & your body.

Déclaration d’exposition aux radiations

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non con

trôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement

et votre corps.

NCC Compliance Statement

低功率電波輻射性電機管理辦法低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公、商號或使用者均不得擅自變更頻率、加大功率或變更原設

計之特性及功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾

時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

電磁波曝露量MPE標準值1mW/cm2，本產品使用時建議應距離人體 20 cm。

1. 使用此產品時應避免影響附近雷達系統之操作。

2. 高增益指向性天線只得應用於固定式點對點系統。

Inhaltsverzeichnis

Andere Cisco Tor Handbücher

Cisco

Cisco VG450 Bedienungsanleitung

Cisco

Cisco IP/VC 3526 Anleitung zur Verwendung

Cisco

Cisco ACE XML Gateway Bedienungsanleitung

Cisco

Cisco DPC3825 Bedienungsanleitung

Cisco

Cisco 3527 PRI G Installations- und Betriebshandbuch

Cisco

Cisco AS5400XM Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Installationshandbuch

Cisco

Cisco VGD-1T3 Bedienungsanleitung

Cisco

Cisco Meraki Z3C Bedienungsanleitung

Cisco

Cisco LINKSYS RFC 2364 Bedienungsanleitung

Cisco

Cisco IG21 Series Bedienungsanleitung

Cisco

Cisco VG202 Bedienungsanleitung

Cisco

Cisco VG30D Bedienungsanleitung

Cisco

Cisco Comcast Xfinity DPC3939 Bedienungsanleitung

Cisco

Cisco Small Business Pro SA520 Fehlerbehebungshandbuch

Cisco

Cisco DPQ2425 Bedienungsanleitung

Cisco

Cisco ISDN GW 3241 Bedienungsanleitung

Cisco

Cisco EPC3925 Bedienungsanleitung

Cisco

Cisco DPC2325 Bedienungsanleitung

Cisco

Cisco Linksys WAG354G(EU) Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco S195 Bedienungsanleitung

Cisco

Cisco ASR 5000 Series Bedienungsanleitung

Cisco

Cisco Network Device MGX 8240 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung