Cisco VG400 series Bedienungsanleitung

Installing the Cisco VG400 Voice Gateway

The following chapter describes how to install and connect a Cisco VG400 Voice Gateway. The following

sections provide the installation procedures in detail:

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work

on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard

practices for preventing accidents. Use the statement number provided at the end of each warning to locate

its translation in the translated safety warnings that accompanied this device. Statement 1071

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement

1030

Warning

Read the installation instructions before using, installing or connecting the system to the power source.

Statement 1004

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations. Statement

1040

Warning

•Safety Recommendations, on page 1

•Unpacking and Inspection, on page 3

•Install the Cisco VG400 Voice Gateway, on page 3

•Connect to Power Supply, on page 10

•Power-On Procedure, on page 10

Safety Recommendations

Before you begin the installation, read the following safety warnings and recommendations. The following

information is included to alert you to safety recommendations and best practices when working with this

equipment.

Installing the Cisco VG400 Voice Gateway

Maintaining Safety with Electricity

Follow these guidelines when working on equipment powered by electricity.

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning

Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There may

be a risk of electric shock from lightning. Statement 1088.

Warning

This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch

the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the

associated circuit-board when the ringer is active. The ringer is activated by an incoming call. Statement 1042

Warning

General Safety Practices

Follow these guidelines to ensure personal safety and to protect the equipment:

• Keep the chassis area clear and dust-free during and after installation.

• Put the removed chassis cover in a safe place.

• Keep tools away from walk areas where you and others could fall over them.

• Do not wear loose clothing that could get caught in the chassis.

• Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

Safety Tips

Use these tips as safety guidelines when installing or working around this equipment:

• Locate the emergency Power-off switch for the room in which you are working. Then, if an electrical

accident occurs, you can act quickly to turn off the power.

• Disconnect all power before installing or removing a chassis.

• Do not work alone if potentially hazardous conditions exist.

• Never assume that power is disconnected from a circuit. Always check.

• Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension

cables, and missing safety grounds.

• If an electrical accident occurs, proceed as follows:

• Use caution; do not become a victim yourself.

• Turn off power to the system.

• If possible, send another person to get medical aid. Otherwise, assess the condition of the victim

and then call for help.

•Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate

action.

Installing the Cisco VG400 Voice Gateway

Maintaining Safety with Electricity

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD occurs when

electronic components are improperly handled; it can result in complete or intermittent failures.

Always follow ESD-prevention procedures when removing and replacing components.

• Ensure that the chassis is electrically connected to earth ground.

• Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.

• Connect the clip to the ESD-strap connection jack (to the left of the power switch on the rear of the

chassis) or to an unpainted chassis frame surface.

For safety, periodically check the resistance value of the antistatic strap, which should be between 1 and 10

megohm (Mohm).

Caution

Unpacking and Inspection

Do not unpack the Cisco VG400 until you are ready to install it. If the installation site is not ready, keep the

chassis in its shipping container to prevent accidental damage.

The Cisco VG400, cables, printed publications, and any optional equipment you ordered might be shipped in

more than one container. When you unpack each shipping container, check the packing list to ensure that you

received all the following items:

• Cisco VG400 Voice Gateway

• Power cord (Auto expland via PDT)

• RJ-45-to-DB-25 adapter cable (labeled Console) - choose an option for this cable, or by default, the auto

expand option is delivered

• RJ-45-to-DB-9 adapter cable (labeled Auxiliary) - choose an option for this cable, or by default, the auto

expand option is delivered

• Rack-mounting - place an order through the ordering tool

Inspect all the items for shipping damage. If anything appears damaged, or if you encounter problems when

installing or configuring your system, contaca customer service representative.

Install the Cisco VG400 Voice Gateway

You can install the Cisco VG400 Voice Gateway in one of the following ways:

Setting the Chassis on a Desktop

You can place the router on a desktop, bench top, or shelf.

Do not set the chassis in an area where the high acoustic noise can be an issue.

Note

Installing the Cisco VG400 Voice Gateway

Preventing Electrostatic Discharge Damage

Do not place anything on top of the hardware that weighs more than 5 lbs. or applies a point load of greater

than 1 lbs. Excessive weight damages the chassis. Additionally, do not stack other electronic equipment on

top of the hardware so as not to impede or interfere with the cooling mechanisms.

Caution

To prevent airflow restriction, allow clearance around the ventilation openings to be at least 1 inch (2.54cms).

Statement 1076.

Warning

After you install the voice gateway, you must connect the chassis to a reliable earth ground. For the chassis

ground connection procedures, see the Chassis Grounding section.

Attach Cisco VG400 Voice Gateway Chassis to Wall

Step 1 Attach the voice gateway chassis to the wall by using the fasteners.

The fasteners that you use must support the weight of the VG400 Voice Gateway.

The head diameter of the fasteners should be sized to fit in the key slot on the chassis bottom. The maximum

diameter of the fastener head should not exceed .250” and the maximum shank diameter should not exceed

.130”.

You must adjust the fastener to allow for the head of the fastener insert into the key slot.

Note

Your chassis installation must allow unrestricted airflow for chassis cooling.

Caution

Step 2 Attach the voice gateway to as shown in the following image.

If you prefer, you can also install the voice gateway diagonally using the other two sides.

Note

Installing the Cisco VG400 Voice Gateway

Attach Cisco VG400 Voice Gateway Chassis to Wall

After you install the voice gateway, you must connect the chassis to a reliable earth ground. For the chassis ground

connection procedure, see the Chassis Grounding section.

Mount Cisco VG400 Voice Gateway Chassis in Rack

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to

ensure that the system remains stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the

unit in the rack. Statement 1006.

Warning

Cisco VG400 Voice Gateway can be installed in 19-inch (48.26-cm) EIA racks. Use the standard brackets

shipped with the hardware for mounting the chassis in a 19-inch EIA rack.

Installing the Cisco VG400 Voice Gateway

Mount Cisco VG400 Voice Gateway Chassis in Rack

You can mount the voice gateway in the following ways:

• Center-front mounting: Brackets attached in the center front of the chassis with only the front panel

facing forward.

•Center-back mounting: Brackets attached in the center back of the chassis with only the back panel facing

forward.

• Front mounting: Brackets attached at the front of the chassis with the front panel facing forward.

• Back mounting: Brackets attached at the back of the chassis with the back panel facing forward.

1. Attach the mounting brackets to the chassis as shown in the following images, using the screws provided.

Do not over-torque the screws. The recommended torque is 15 to 18 inch-lb (1.7 to 2.0 N-m).

Caution

2. Attach the second bracket to the opposite side of the chassis. Use a number-2 Phillips screwdriver to

install the number-8 bracket screws.

Your chassis installation must allow unrestricted airflow for chassis cooling.

Caution

Figure 1: Bracket Installation for Front Mounting

Installing the Cisco VG400 Voice Gateway

Mount Cisco VG400 Voice Gateway Chassis in Rack

Installing the Cisco VG400 Voice Gateway

Mount Cisco VG400 Voice Gateway Chassis in Rack

Figure 2: Bracket Installation for Back Mounting

19-inch EIA brackets4Screws3

3. Use the screws provided with the rack to install the chassis in the rack. For the 19-inch EIA bracket, start

the lower pair of screws first, and rest the brackets on the lower screws while you insert the upper pair of

screws.

Installing the Cisco VG400 Voice Gateway

Mount Cisco VG400 Voice Gateway Chassis in Rack

The screw slots in the brackets are spaced to line up with every second pair of screw holes in the rack. When

the correct screw holes are used, the small, threaded holes in the brackets line up with unused screw holes in

the rack. If the small holes do not line up with the rack holes, you must raise or lower the brackets to the next

rack hole.

Tip

Mounting Screws (4)1

After you install the voice gateway, you must connect the chassis to a reliable earth ground. For the chassis

ground connection procedures, see the Chassis Grounding section.

Chassis Grounding

To reduce the risk of electric shock, the chassis of this equipment needs to be connected to permanent earth

ground during normal use. Statement 445

Warning

Use a size 14 AWG (2 mm2) or larger copper wire and an appropriate user-supplied ring terminal with an

inner diameter of 1/4 in. (5–7 mm).

To install the ground connection for your router, perform the following steps:

Step 1 Strip one end of the ground wire to the length required for the ring terminal.

Step 2 Crimp the ground wire to the ring terminal, using a crimp tool of the appropriate size.

Step 3 Attach the ground lug or ring terminal to the chassis as shown in the following image. Use one of the screws provided.

Tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m).

Figure 3: Chassis Ground Connection on the Voice Gateway

Installing the Cisco VG400 Voice Gateway

Chassis Grounding

Step 4 Connect the other end of the ground wire to a known reliable earth ground point at your site.

Connect to Power Supply

This section explains how to connect AC power to the voice gateway.

Read the installation instructions before using, installing or connecting the system to the power source.

Statement 1004

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the

protective device is rated not greater than: 20A Statement 1005

Warning

To connect the Cisco Voice Gateway to an AC power outlet, perform the following steps:

1. Connect the AC adapter to an AC power outlet.

2. Plug the adapter cord into the router.

Power-On Procedure

Perform this procedure to power on your Cisco VG400 Voice Gateway, and verify that it goes through its

initialization and self-test. When this is finished, the Cisco VG400 Voice Gateway is ready to configure.

To power on the Cisco VG400 Voice Gateway, perform the following:

Before you begin

Before you power on the Cisco VG400 Voice Gateway, ensure that:

• The chassis is securely mounted

• Power cable is connected

• Interface cables are connected

SUMMARY STEPS

1. Power on your terminal or PC, and configure it for 9600 bps, 8 data bits, 1 stop bit, and no parity.

2. Move the Cisco VG400 Voice Gateway power switch to the ON position.

3. Enter no to proceed with manual configuration using the CLI:

4. Press Return to terminate autoinstall and continue with manual configuration.

5. Press Return to bring up the Router> prompt:

6. Enter privileged EXEC mode:

7. Continue with the Troubleshooting section.

Installing the Cisco VG400 Voice Gateway

Connect to Power Supply

Andere Handbücher für VG400 series

Inhaltsverzeichnis

Andere Cisco Tor Handbücher

Cisco

Cisco EVM-IPVS-16A Kurzanleitung

Cisco

Cisco AS5350 - Universal Access Server Bedienungsanleitung

Cisco

Cisco 1100 Series Handbuch

Cisco

Cisco Linksys WAG310G Bedienungsanleitung

Cisco

Cisco SPA3000 Bedienungsanleitung

Cisco

Cisco EPC2425 Bedienungsanleitung

Cisco

Cisco VG400 series Handbuch

Cisco

Cisco ASR 5000 Bedienungsanleitung

Cisco

Cisco DPC2425 Bedienungsanleitung

Cisco

Cisco IntraPort Carrier-8 Service-Handbuch

Cisco

Cisco AudioCodes MP-1288 Bedienungsanleitung

Cisco

Cisco REN301 Bedienungsanleitung

Cisco

Cisco Linksys SPA400 Bedienungsanleitung

Cisco

Cisco DPC3848V Bedienungsanleitung

Cisco

Cisco IG21 Series Handbuch

Cisco

Cisco ENH900EXT Bedienungsanleitung

Cisco

Cisco DPC3827 Bedienungsanleitung

Cisco

Cisco VG350 Bedienungsanleitung

Cisco

Cisco UNIFIED COMMUNICATIONS UC320W Bedienungsanleitung

Cisco

Cisco Small Business Pro SA520 Fehlerbehebungshandbuch

Cisco

Cisco VG224 - Analog Phone Gateway Bedienungsanleitung

Cisco

Cisco IG21 Series Bedienungsanleitung

Cisco

Cisco IP/VC 3526 Anleitung zur Verwendung

Cisco

Cisco 450 Handbuch

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung