Cisco EVM-IPVS-16A Kurzanleitung

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Connecting Cisco Analog Video Gateway

Network Modules to the Network

Revised: May 1, 2008, OL-16670-01

This guide describes how to connect Cisco Analog Video Gateway network modules to your network. It

contains the following sections:

•Information About the EVM-IPVS-16A Network Module, page 1

•How to Install, Connect, or Replace the EVM-IPVS-16A Network Module, page 5

•Related Documents, page 12

•Obtaining Documentation, Obtaining Support, and Security Guidelines, page 13

Information About the EVM-IPVS-16A Network Module

The EVM-IPVS-16A network module enables Cisco integrated services routers to capture analog video

signals. The EVM-IPVS-16A network module supports up to 16 simultaneous composite video inputs,

such as video surveillance cameras. The EVM-IPVS-16A network module also provides alarm input

detection, control relay outputs, and RS-485 serial communication interfaces. Figure 1 shows the

EVM-IPVS-16A network module faceplate.

Note You need a router that supports the EVM-IPVS-16A network module. For a list of supported platforms,

see the Cisco Analog Video Gateway Network Module (EVM-IPVS-16A) Data Sheet.

Connecting Cisco Analog Video Gateway Network Modules to the Network

Information About the EVM-IPVS-16A Network Module

Connecting Cisco Analog Video Gateway Network Modules to the Network

Figure 1 Cisco Analog Video Gateway Network Module (EVM-IPVS-16A) Faceplate

Warning

Equipment connected to outdoor cameras must be permanently grounded in accordance with national

and local codes.

Statement 374

Warning

Hazardous voltages may be present in the outdoor camera cables under fault conditions. Disconnect

all cables from the outdoor cameras before servicing this equipment.

Statement 376

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be

accessed only through the use of a special tool, lock and key, or other means of security.

Statement

1017

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Note The compact flash module installed in the EVM-IPVS-16A network module is not field-replaceable.

Note For software-related prerequisites and restrictions, see the Cisco Analog Video Gateway 1.0 Installation

and Upgrade Guide at:

http://www.cisco.com/en/US/docs/video/cavg/cavginstall/cavginstall.html.

Note For EVM-IPVS-16A network module features and benefits, supported hardware and software, and other

product information, see the Cisco Analog Video Gateway Network Module (EVM-IPVS-16A) Data

Sheet.

Video Ports

16 video ports are provided, video ports 0 and 1 can be configured for input or output. The remaining 14

video ports can be configured for input only.

3210

EVM

IPVS-16A

170291

Connecting Cisco Analog Video Gateway Network Modules to the Network

Information About the EVM-IPVS-16A Network Module

Connecting Cisco Analog Video Gateway Network Modules to the Network

RS-485 Serial Communication Interfaces

The EVM-IPVS-16A network module supports a half-duplex, two-wire RS-485 communication

network, which sometimes is called a ring. The EIA/TIA RS-485 communications standard supports up

to 32 devices (driver/receiver pairs) on a cable of up to 4,000 feet. The EVM-IPVS-16A network module

has two RS-485 ports, supporting up to 64 devices. The EVM-IPVS-16A network module typically acts

as the master for each of the two RS-485 networks.

The RS-485 ports can be used to control camera pan, tilt, and zoom (PTZ) functions, as well as other

RS-485 devices. Because PTZ camera types use different protocols, the EVM-IPVS-16A network

module only supports pass-through mode. In pass-through mode PTZ commands and other data will not

be interpreted.

Alarm Inputs and Control Relay Outputs

The EVM-IPVS-16A network module supports eight contact closure interfaces. Interfaces A0, A1, A2,

and A3 can be configured as alarm input or relay output, the other interfaces are input only. They are

used to detect contact trigger events and control external devices.

In most cases, the contact closure interfaces will be connected to a patch panel through the two terminal

block ports on the network module. The patch panel can provide the bias to the circuit.

Caution The alarm signal input and output (I/O) connections on this unit are intended only for connection to

NEC/CEC Class 2 or equivalent circuit. This means that the voltages applied to alarm signal I/O

connections should not exceed 42.4 Vpk or 60 Vdc and it should be a limited/fused power source. For

more details on Class 2 circuits, refer to the National Electrical Code/Canadian Electrical Code.

Gigabit Ethernet Port

The external Gigabit Ethernet port is disabled by default. If you enable the Gigabit Ethernet interface, it

can act as a routable interface in your network.

Table 1 Alarm Input and Output Interface Specifications

Specification Range

Alarm Input Sense Voltage Range 12 V to 24 V

Alarm Output Current Load Range 0 mA to 170 mA

Connecting Cisco Analog Video Gateway Network Modules to the Network

Information About the EVM-IPVS-16A Network Module

Connecting Cisco Analog Video Gateway Network Modules to the Network

EVM-IPVS-16A Network Module Connectors

The physical connectors that appear on the EVM-IPVS-16A network module are shown in Figure 2 and

described in Table 2.

Figure 2 EVM-IPVS-16A Network Module Connectors

EVM-IPVS-16A Network Module LEDs

The Cisco analog video gateway network module (EVM-IPVS-16A) has LEDs which denote the status

of the network module, shown in Figure 3 and described in Table 3.

Table 2 EVM-IPVS-16A Network Module Connectors

Figure

Ref. Connector Type Connects To

1 Terminal block 0 10-input terminal block (ports

A0-A3 and S0)

10-position terminal block connector (provided)

2 Terminal block 1 10-input terminal block (ports

A4-A7 and S1)

10-position terminal block connector (provided)

3 Gigabit Ethernet (labeled

GigE)

RJ-45 female connector Straight-through two-pair Category 5

unshielded twisted-pair (UTP) cable

4 Video (labeled VIDEO) DB-37 female connector DB-37 to BNC video breakout cable (provided)

EVM

IPVS-16A

230442

Connecting Cisco Analog Video Gateway Network Modules to the Network

How to Install, Connect, or Replace the EVM-IPVS-16A Network Module

Connecting Cisco Analog Video Gateway Network Modules to the Network

Figure 3 EVM-IPVS-16A Network Module LEDs

How to Install, Connect, or Replace the EVM-IPVS-16A Network

Module

This section contains the following procedures, each of which may or may not be required, depending

on which tasks your service provider performs for you:

•Installing the EVM-IPVS-16A Network Module in the Router Chassis, page 6

•Connecting the EVM-IPVS-16A Network Module to the Network, page 8

Table 3 EVM-IPVS-16A Network Module LED Descriptions

Figure

Ref. LED State Meaning Possible Causes and Corrective Actions

1 LINK Green Gigabit Ethernet link is up. Normal indication. No action required.

Off Gigabit Ethernet link is down. Check Gigabit Ethernet cable connections.

2 ACT Amber Gigabit Ethernet link is actively

transmitting or receiving.

Normal indication. No action required.

Off Gigabit Ethernet link is not actively

transmitting or receiving.

Normal indication. No action required.

3Video

signal

ports

0-15

Green There is an active video session for this

port, and input video is detected.

Normal indication. No action required.

Amber There is an active video session for this

port, but no input video is detected.

Check the camera is on, then check the video

port cable connections.

Off There is no active video session for this

port.

Check the video port cable connections.

See the “Connecting the EVM-IPVS-16A

Network Module to the Network” section on

page 8.

4 EN On The router’s Cisco IOS software recognizes

the network module.

Normal indication. No action required.

Off The router’s Cisco IOS software does not

recognize the network module.

Verify that the network module is properly

installed in the router chassis. See the “Installing

Cisco Network Modules in Cisco Access

Routers” chapter.

3210

EVM

IPVS-16A

230443

1 2 4

Connecting Cisco Analog Video Gateway Network Modules to the Network

How to Install, Connect, or Replace the EVM-IPVS-16A Network Module

Connecting Cisco Analog Video Gateway Network Modules to the Network

•Performing Online Insertion and Removal of the EVM-IPVS-16A Network Module, page 10

Installing the EVM-IPVS-16A Network Module in the Router Chassis

To install the EVM-IPVS-16A network module in the router chassis, see the Installing Cisco Network

Modules in Cisco Access Routers guide at:

http://www.cisco.com/en/US/docs/routers/access/interfaces/nm/hardware/installation/guide/InstNetM.

html

Note The EVM-IPVS-16A network module can only be installed in slots that support extension modules. For

information about which slots support extension modules, see Table 1-1 on page 5

Wiring the Terminal Block Connectors

Wire the provided terminal block connectors using the pinout information provided in Table 4. (See

Figure 4.)

Note The wires used to connect to the terminal block are required to be between 26 AWG and 18 AWG.

Figure 4 Wiring the Terminal Block Connectors

Table 4 lists each pin on the terminal block, and the corresponding port information.

Tip When you wire the terminal block connector, label each wire with the pin number, so you can easily

connect the wires to the alarm or RS-485 devices in your network.

230462

Connecting Cisco Analog Video Gateway Network Modules to the Network

How to Install, Connect, or Replace the EVM-IPVS-16A Network Module

Connecting Cisco Analog Video Gateway Network Modules to the Network

Note In Table 4 a plus (+) sign and minus (–) sign are used to note the polarity for the contact closure and

RS-485 ports. For contact closure ports, pins noted with a plus sign must be connected to positive

potential; pins noted with a minus sign must be connected to negative potential. For RS-485 ports, pins

noted with a plus sign must be connected to an RS-485 device non-inverting terminal; pins noted with a

minus sign must be connected to an RS-485 device inverting terminal.

Table 4 EVM-IPVS-16A Terminal Block Pinouts

Pin Type

Terminal Block 0 (Lower)

1 RS-485 S0 +

2 RS-485 S0 –

3 In-Out A0 +

4 In-Out A0 –

5 In-Out A1 +

6 In-Out A1 –

7 In-Out A2 +

8 In-Out A2 –

9 In-Out A3 +

10 In-Out A3 –

Terminal Block 1 (Upper)

11 RS-485 S1 +

12 RS-485 S1 –

13 In A4 +

14 In A4 –

15 In A5 +

16 In A5 –

17 In A6 +

18 In A6 –

19 In A7 +

20 In A7 –

Connecting Cisco Analog Video Gateway Network Modules to the Network

How to Install, Connect, or Replace the EVM-IPVS-16A Network Module

Connecting Cisco Analog Video Gateway Network Modules to the Network

Connecting the EVM-IPVS-16A Network Module to the Network

This section describes how to connect the EVM-IPVS-16A network module to devices in the video

surveillance network.

Note If an installation technician has already connected the EVM-IPVS-16A to the devices in your network,

then do not perform this task. Instead, proceed directly to the software configuration for your

EVM-IPVS-16A network module. See the Cisco Analog Video Gateway 1.0 Installation and Upgrade

Guide at:

http://www.cisco.com/en/US/docs/video/cavg/cavginstall/cavginstall.html

Prerequisites

•Install the EVM-IPVS-16A network module in the router chassis. See the Installing Cisco Network

Modules in Cisco Access Routers guide at:

http://www.cisco.com/en/US/docs/routers/access/interfaces/nm/hardware/installation/guide/InstNe

tM.html

•Wire the provided terminal block connectors. See the “Wiring the Terminal Block Connectors”

section on page 6.

Steps

To connect the EVM-IPVS-16A network module to the network, follow these steps:

Step 1 Take the DB-37 end of the provided DB-37 to BNC video breakout cable, and connect it to the VIDEO

connector on the EVM-IPVS-16A network module.

Connecting Cisco Analog Video Gateway Network Modules to the Network

How to Install, Connect, or Replace the EVM-IPVS-16A Network Module

Connecting Cisco Analog Video Gateway Network Modules to the Network

Figure 5 Connecting the Video Breakout Cable to the EVM-IPVS-16A Network Module

Warning

Equipment connected to outdoor cameras must be permanently grounded in accordance with national

and local codes.

Statement 374

Step 2 Connect the BNC ends of the video breakout cable to the cameras in your network. The cable ends are

labeled with the corresponding port number (0-15).

Step 3 After you have wired the provided terminal block connectors according to the pinout information

provided in Table 4, connect the terminal block connectors to the terminal block on the EVM-IPVS-16A

network module and tighten the screws using a small slotted screwdriver.

Figure 6 Connecting the Terminal Block Connectors to the EVM-IPVS-16A Network Module

230459

230460

Connecting Cisco Analog Video Gateway Network Modules to the Network

How to Install, Connect, or Replace the EVM-IPVS-16A Network Module

Connecting Cisco Analog Video Gateway Network Modules to the Network

Step 4 Connect the other end of the wired terminal block connectors to the RS-485 and contact closure devices

in your network. In most cases, the wires will be connected to a patch panel.

Step 5 (Optional) To connect the EVM-IPVS-16A network module to an external device, use a straight-through

two-pair Category 5e unshielded twisted-pair (UTP) cable, and connect the RJ-45 Gigabit Ethernet port

on the network module to a switch, hub, repeater, server, or other Gigabit Ethernet network device.

What to Do Next

Proceed to the software configuration for your EVM-IPVS-16A network module. See the Cisco Analog

Video Gateway 1.0 Installation and Upgrade Guide at:

http://www.cisco.com/en/US/docs/video/cavg/cavginstall/cavginstall.html

Performing Online Insertion and Removal of the EVM-IPVS-16A Network

Module

The online insertion and removal (OIR) feature enables some Cisco modular access routers to support

the replacement of network modules without switching off the router or affecting the operation of other

interfaces. Also, routing information is maintained during OIR of network modules.

Note If your router does not support OIR, do not perform this task to replace your EVM-IPVS-16A network

module. Instead, see the Installing Cisco Network Modules in Cisco Access Routers guide at:

http://www.cisco.com/en/US/docs/routers/access/interfaces/nm/hardware/installation/guide/InstNetM.

html

Restrictions

•Only the Cisco 3845 router supports OIR of the EVM-IPVS-16A network module.

•All connections made through the EVM-IPVS-16A network module are reset during OIR.

•You must perform OIR with similar modules. If you remove a network module, install another

network module exactly like it in its place.

Steps

To perform OIR of the EVM-IPVS-16A network module in your router, follow these steps:

Step 1 Initiate a console session with your router.

Step 2 Enter configuration mode and shut down the interface:

Router> enable

Router# configure terminal

Router(config)# interface video-Service-Engine slot/0

Router(config-if)# shut

Router(config-if)# shutdown

Router(config-if)# exit

Inhaltsverzeichnis

Andere Cisco Tor Handbücher

Cisco

Cisco IC3000 Bedienerhandbuch

Cisco

Cisco VG248 - Gateway Bedienungsanleitung

Cisco

Cisco Physical Access CIAC-GW-K9 Bedienungsanleitung

Cisco

Cisco VG30D Bedienungsanleitung

Cisco

Cisco DPC3949 Bedienungsanleitung

Cisco

Cisco DPC2434 Bedienungsanleitung

Cisco

Cisco ASR 5000 Bedienungsanleitung

Cisco

Cisco Catalyst CG113-W6 Handbuch

Cisco

Cisco VG224 - Analog Phone Gateway Bedienungsanleitung

Cisco

Cisco VG310 Handbuch

Cisco

Cisco SPA-841 - Sipura VoIP Phone Bedienungsanleitung

Cisco

Cisco Small Business SPA8000 Original Betriebsanleitung

Cisco

Cisco Linksys WAG325N Bedienungsanleitung

Cisco

Cisco AS5400XM Bedienungsanleitung

Cisco

Cisco Linksys WAG354G(EU) Bedienungsanleitung

Cisco

Cisco LINKSYS AG241 Bedienungsanleitung

Cisco

Cisco ASR 5000 Series Bedienungsanleitung

Cisco

Cisco Meraki Z3C Bedienungsanleitung

Cisco

Cisco ASR 5x00 Home eNodeB Bedienungsanleitung

Cisco

Cisco IR510 Handbuch

Cisco

Cisco DPC3929CM Bedienungsanleitung

Cisco

Cisco EPC2434 Bedienungsanleitung

Cisco

Cisco RFGW-10 Handbuch

Cisco

Cisco Connected Life CLG-8202-WW Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung