Cisco 500 Series Bedienungsanleitung

Headsets

•Important Headset Safety Information, on page 1

•Cisco Headset 500 Series, on page 1

•Cisco Headset 700 Series, on page 12

•Third Party Headsets, on page 15

•Cisco Headset Configuration on Cisco Unified Communications Manager, on page 18

•Connect a Headset to Your Phone, on page 26

•Postpone a Phone Upgrade, on page 29

•Cisco Headset Customization, on page 29

•Configure a Headset on the Phone, on page 32

•Make a Call with a Standard Headset, on page 35

•Audio Path Selection, on page 35

•Swap Headsets While on a Call, on page 35

•Troubleshoot Your Cisco Headset, on page 36

Important Headset Safety Information

High Sound Pressure—Avoid listening to high volume levels for long periods to prevent

possible hearing damage.

When you plug in your headset, lower the volume of the headset speaker before you put the headset on. If

you remember to lower the volume before you take the headset off, the volume will start lower when you

plug in your headset again.

Be aware of your surroundings. When you use your headset, it may block out important external sounds,

particularly in emergencies or in noisy environments. Don’t use the headset while driving. Don’t leave your

headset or headset cables in an area where people or pets can trip over them. Always supervise children who

are near your headset or headset cables.

Cisco Headset 500 Series

The following Cisco headsets are available:

• Cisco Headset 521—A headset with a single earpiece that comes with an inline USB controller.

Headsets

• Cisco Headset 522—A headset with a dual earpiece that comes with an inline USB controller.

• Cisco Headset 531—A headset with a single earpiece that can be used as either a standard headset or a

USB headset with the USB adapter.

• Cisco Headset 532—A standard headset with a dual earpiece that can be used as either a standard headset

or a USB headset with the USB adapter.

• Cisco Headset 561—A wireless headset with a single earpiece that comes with a base.

• Cisco Headset 562—A wireless headset with a dual earpiece that comes with a base.

Cisco Headset 521 and 522

The Cisco Headset 521 and 522 are two wired headsets that have been developed for use on Cisco IP Phones

and devices. The Cisco Headset 521 features a single earpiece for extended wear and comfort. The Cisco

Headset 522 features two earpieces for use in a noisy workplace.

Both headsets feature a 3.5-mm connector for use on laptops and mobile devices. An inline USB controller

is also available for use on the Cisco IP Phone 8851, 8851NR, 8861, 8865, and 8865NR. The controller is an

easy way answer your calls, and to access basic phone features such as hold and resume, mute, and volume

control.

Phone Firmware Release 12.1(1) and later is required for these headsets to function properly.

Figure 1: Cisco Headset 521

Figure 2: Cisco Headset 522

Headsets

Cisco Headset 500 Series

Cisco Headset 531 and 532

The Cisco Headset 531 and 532 can be used as standard headsets on the phones. You plug the headset into

the headset port using the RJ connector.

The Cisco Headset USB Adapter is also available for use on the Cisco IP Phone 8851, 8851NR, 8861, 8865,

and 8865NR. The adapter converts the Cisco Headset 531 and 532 into a USB headset, and it gives you a few

extra features. It provides a convenient way to handle calls, to test your microphone, and to customize your

bass and treble, gain, and sidetone settings.

Phone Firmware Release 12.1(1) and later is required for the headsets to function properly.

Figure 3: Cisco Headset 531

Figure 4: Cisco Headset 532

Cisco Headset 561 and 562

Cisco Headset 561 and 562 are two wireless headsets that have been developed for use in today's office. The

Cisco Headset 561 features a single earpiece for extended wear and comfort. Cisco Headset 562 features two

earpieces for use in a noisy workplace.

Both headsets come with either the Standard base or the Multibase for charging your headset, and for monitoring

the headset power level with the LED display. Both bases also displays your call status, such as incoming

call, active call, and calls on mute. If your headset is upgrading the firmware, then the LEDs show the upgrade

progress.

The base connects to the phone using either a USB connector or a Y cable depending upon your phone model

and your personal preference. The Y cable plugs into the AUX and headset ports of the phone.

An AC plug is included for connecting the base to a power outlet. You have to install the power clip for your

region before you can plug in the power adapter.

Headsets

Cisco Headset 500 Series

Occasionally a tone is played over your Cisco Headset 561 or 562. Some of these tones alert you when you

perform an action, such as pressing a button. Other tones warn you that the headset requires attention, such

as when the battery needs recharging, or when you are too far from the base station.

Phone Firmware Release 12.5(1) or later and the defaultheadsetconfig.json file for the Cisco Headset 561 and

562 to function properly with Cisco Unified Communications Manager 12.5(1) or earlier.

Figure 5: Cisco Headset 561

Figure 6: Cisco Headset 562

Cisco Headset 500 Series Support

The Cisco IP Phone 7811 is the only phone in the Cisco IP Phone 7800 Series that does not support a headset.

The Cisco IP Phone 7821, 7841, and 7861 use an RJ-style connector to connect with a headset or base.

The Cisco IP Phone 8800 Series has both RJ-style connectors and USB ports to connect to headsets and bases

to a phone. But the type of connection depends upon your phone model. The following table describes headset

connection and phone model support on the Cisco IP Phone 8800 Series.

Headsets

Cisco Headset 500 Series

Table 1: Headset Support on the Cisco IP Phone 8800 Series.

Cisco IP Phone 8851

Cisco IP Phone 8851NR

Cisco IP Phone 8861

Cisco IP Phone 8865

Cisco IP Phone 8865NR

Cisco IP Phone 8811

Cisco IP Phone 8841

Cisco IP Phone 8845

Cisco Headset 500 Series

Supported

(With USB Inline Controller)

Not SupportedCisco Headset 521

Cisco Headset 522

Supported

(RJ connector or with USB Adapter)

Supported

(RJ connector)

Cisco Headset 531

Cisco Headset 532

Supported

(Y-cable or USB cable)

Supported

(Y-cable)

Cisco Headset 561

Cisco Headset 562

Cisco Headset 521 and 522 Controller Buttons and Hardware

Your controller buttons are used for basic call features.

Figure 7: Cisco Headset 521 and 522 Controller

The following table describes the Cisco Headset 521 and 522 controller buttons.

Table 2: Cisco Headset 521 and 522 Controller Buttons

DescriptionNameNumber

Toggle the microphone on and off.Mute button1

Adjust the volume on your headset.Volume button2

Headsets

Cisco Headset 521 and 522 Controller Buttons and Hardware

DescriptionNameNumber

Use to manage calls:

• Press once to answer an incoming call.

• Press and hold to end a call.

• Press twice to reject an incoming call.

• Press once to put an active call on hold. Press again to

retrieve a call from hold.

• Press once to put an active call on hold, and to answer an

incoming call.

Call3

Cisco Headset 531 and 532 USB Adapter Buttons and Hardware

Your adapter is used for basic call features.

Figure 8: Cisco Headset USB Adapter

The following table describes the Cisco Headset USB Adapter buttons.

Table 3: Cisco USB Adapter Buttons

DescriptionNameNumber

Toggle the microphone on and off.Mute button1

Adjust the volume on your headset.Volume button2

Headsets

Cisco Headset 531 and 532 USB Adapter Buttons and Hardware

DescriptionNameNumber

Use to place, answer, and manage your calls:

• Press once to place a call.

• Press once to answer an incoming call. Press twice to reject

an incoming call.

• Press once to put an active call on hold, and to answer an

incoming call.

• Press once to put an active call on hold.

• Press and hold to end a call.

Call button3

Cisco Headset 561 and 562 Buttons and LED

Your headset buttons are used for basic call features.

Figure 9: Cisco Headset 561 and 562 Headset Buttons

Headsets

Cisco Headset 561 and 562 Buttons and LED

The following table describes the Cisco Headset 561 and 562 Headset buttons.

Table 4: Cisco Headset 561 and 562 Headset Buttons

DescriptionNameNumber

Use to power the headset on and off.

Press and hold for 4 seconds to power on and off the headset.

Incoming and active call management depends upon if you have

one call or multiple calls.

One call:

• Press once to answer incoming calls.

• Press once to put an active call on hold. Press again to

retrieve a call from hold.

• Press twice to reject an incoming call.

• Press and hold to end an active call.

Multiple calls:

• Press once to put an active call on hold, and to answer a

second incoming call.

•Press once to put a current call on hold. Press again to resume

a call, or press and hold for 2 seconds to end the current call

and to resume a held call.

• Press and hold to end an active call, and to answer another

incoming call.

• Press twice to stay on a current call, and to reject a second

incoming call.

Power and Call button1

Toggle the microphone on and off. The Mute on the phone

lights when Mute on the headset is enabled.

Mute button2

Adjust the volume on your headset.Volume button3

Shows the headset status:

• Blinking red—Incoming call.

• Steady red—Active call.

• Blinking white—Firmware upgrade is in progress.

LED4

Headsets

Cisco Headset 561 and 562 Buttons and LED

Cisco Headset 560 Series Standard Base

The standard base charges your headset and has LEDs that shows your headset's battery level and call state.

You can also answer and end calls when you lift or place your headset on the base.

The standard base comes with the following connector cables:

• USB to USB Cable: for devices with USB connectivity

• USB Y-Cable: for Cisco IP Phones without a USB port

• USB-A to USB-C Cable: available separately for PC or Mac devices.

Figure 10: Standard Base LEDs

The following table describes the standard base.

Table 5: Standard Base LEDs

DescriptionNameNumber

Indicates the headset battery charge and base status:

• Headset battery strength—LEDs blink and change to

solid as the battery charges.

• Headset update in progress—LEDs blink in sequence,

left to right.

• Headset and base not paired—All LEDs blink

• Power save mode—Middle LED shows solid.

The base enters power save mode when there is no call source

connectivity after 10 minutes.

Battery Status LED1

Headsets

Cisco Headset 560 Series Standard Base

DescriptionNameNumber

Alerts you to the call state:

• Incoming call—Blinking green

• Active call—Steady green

• Muted call—Steady red

Call Status LED2

Cisco Headset 560 Series Multibase

The multibase can connect up to three call sources through Bluetooth, the USB connector, or the Y-cable.

The multibase can save up to four Bluetooth devices. You can switch between call sources using the buttons

on the multibase. You use the call control buttons on the headset to answer and end calls. When your headset

is in the base, you automatically answer the call when you remove the headset from the base. You can return

the headset to the base to end the call.

The multibase comes with the following connector cables:

• USB to USB Cable: for Cisco IP Phones with USB connectivity

• USB Y-Cable: for Cisco IP Phones without a USB port

• Mini USB Cable: for PC or Mac.

• Mini USB to USB-C Cable: available separately for PC or Mac devices.

Figure 11: Multibase LEDs

The following table describes the Cisco Headset 560 Series Multibase multibase LEDs.

Headsets

Cisco Headset 560 Series Multibase

Andere Handbücher für 500 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Headset Handbücher

Cisco

Cisco 500 Series Bedienungsanleitung

Cisco

Cisco 700 series Bedienungsanleitung

Cisco

Cisco 730 Bedienungsanleitung

Cisco

Cisco Cisco Headset 561 Bedienungsanleitung

Cisco

Cisco 500 Series Bedienungsanleitung

Cisco

Cisco 232D Bedienungsanleitung

Cisco

Cisco Jawbone ICON Bedienungsanleitung

Cisco

Cisco 730 Bedienungsanleitung

Cisco

Cisco 500 Series Bedienungsanleitung

Cisco

Cisco 730 Bedienungsanleitung

Cisco

Cisco Cisco Headset 561 Bedienungsanleitung

Cisco

Cisco Cisco Headset 561 Bedienungsanleitung

Cisco

Cisco Cisco Headset 561 Bedienungsanleitung

Cisco

Cisco Cisco Headset 562 Bedienungsanleitung

Cisco

Cisco 531 Bedienungsanleitung

Cisco

Cisco 500 Series Bedienungsanleitung

Cisco

Cisco 500 Series Leitfaden

Cisco

Cisco Headset 530 Series Bedienungsanleitung

Cisco

Cisco 730 Bedienungsanleitung

Cisco

Cisco Cisco Headset 561 Bedienungsanleitung

Cisco

Cisco 520 Series Bedienungsanleitung

Cisco

Cisco Headset 560 Series Bedienungsanleitung

Cisco

Cisco Aironet 521 Bedienungsanleitung

Beliebte Headset Handbücher anderer Marken

Sena

Sena SMH10 Bedienungsanleitung

IASUS

IASUS Stealth IA-NT4-BASIC-BT Bedienungsanleitung

Sennheiser

Sennheiser EPOS ADAPT 230 Bedienungsanleitung

GE 98971 Bedienungsanleitung

Hama

Hama 00184070 Bedienungsanleitung

Plantronics

Plantronics Blackwire 3200 Series Bedienungsanleitung

Blue Tiger

Blue Tiger Advantage PLUS Bedienungsanleitung

Jawbone

Jawbone Icon Bedienungsanleitung

Jabra

Jabra FR 20 Bedienungsanleitung

Roxcore

Roxcore Flow A+ Bedienungsanleitung

Turtle Beach

Turtle Beach XP 510 Bedienungsanleitung

Philips

Philips SHB6101 Bedienungsanleitung

Jabra

Jabra PRO 9460 Duo Bedienungsanleitung

HyperX

HyperX HyperX Cloud Flight Bedienungsanleitung

Bose

Bose MIE2 Mobile Bedienungsanleitung

Jabra

Jabra Steel Bedienungsanleitung

HyperX

HyperX cloud ii Bedienungsanleitung

Southwing

Southwing SA505 Bedienungsanleitung