Cisco 7906G - Unified IP Phone VoIP Bedienungsanleitung

Using a Handset, Headset, and Speaker

Cisco Unified IP Phone 7906G and 7911G User Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP) 1

Using a Handset, Headset, and Speaker

The Cisco Unified IP Phone 7906G and 7911G provide a speaker for hands-free listening. When you

use the speaker, you can hear the conversation but cannot talk because the phone does not contain a

built-in microphone. To talk on a call, you must use the handset.

You can use the speaker in one of two ways, depending on how your system administrator enables the

phone. Your phone may be enabled for one of the following features, but not both at the same time:

•Group Listen

•Monitor (default)

Using the Group Listen Feature

The following table shows how you can use the Group Listen feature.

If you want to... Then...

Use the handset Lift it to go off-hook; replace it to go on-hook.

Talk using the handset and listen

on the speaker at the same time

(Group Listen)

Press GListen.

Note Group Listen must be enabled by your system administrator

for the GListen softkey to display.

Turn off Group Listen and use the

handset

Press GLOff.

Hang up after using Group Listen Press EndCall or hang up.

Adjust the volume level for a call Note When using Group Listen, adjusting the volume only

changes the volume for the speaker and not the handset.

Press the up or down Volume button during a call or after

invoking a dial tone.

Press Save to preserve the volume level for future calls.

2OL-22336-01

Using the Monitor Feature

The following table shows how you can use the Monitor feature.

Tips

•If your system administrator has disabled the speaker on your phone, the GListen, GLOff,

Monitor, and MonOff softkeys will not be available to you. You must lift the handset to place and

monitor calls.

•Pressing the Volume button changes the volume for the handset or speaker, depending on which

device is in use. In Group Listen and Monitor modes, the volume adjustment is for the speaker

and not the handset.

Note If you need to change the wideband setting for your handset (for example, if you change your

handset) press and choose Settings > User Preferences > Audio Preferences > Wideband

Handset. If the Wideband Handset setting shows as dimmed, then this setting is not user

controllable.

Check with your system administrator to be sure your phone system is configured to use

wideband. If the system is not configured for wideband, you may not detect any additional

audio sensitivity even when using a wideband handset. To learn more, refer to the handset

documentation or ask your system administrator for assistance.

If you want to... Then...

Use the handset Lift it to go off-hook; replace it to go on-hook.

Listen to the call on the speaker Press Monitor and then hang up the handset. You will be able to

hear the call but you will not be able to talk on the call.

Note The Monitor and MonOff softkeys are not available if

Group Listen is enabled.

Turn off the speaker and use the

handset

Lift the handset, or press MonOff.

Note The Monitor and MonOff softkeys are not available if

Group Listen is enabled.

Turn off the speaker and hang up Press EndCall.

Adjust the speaker volume level

for a call

Press the up or down Volume button during a call or after

invoking a dial tone.

Press Save to preserve the volume level for future calls.

Using a Handset, Headset, and Speaker

Cisco Unified IP Phone 7906G and 7911G User Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP) 3

Using a Headset

To use a headset, disconnect the handset and connect a headset to the Handset port. For information

about purchasing headsets, see Headset Support, page 3.

Using Wideband with your Headset

If you connect a headset to the handset port, be sure that the Wideband Handset setting is disabled.

Choose User Preferences > Audio Preferences > Wideband Handset.

Note If the Wideband Handset setting shows as dimmed, then this setting is not user controllable

and you must contact your system administrator to change this setting.

Using AutoAnswer

When AutoAnswer is enabled, your phone answers incoming calls automatically after a few rings.

Your system administrator can configure AutoAnswer to use the speaker to answer calls. However,

you can only monitor the call using the speaker. To talk to the caller, you must pick up the handset.

4OL-22336-01

Andere Handbücher für 7906G - Unified IP Phone VoIP

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco IP-Telefon Handbücher

Cisco

Cisco 3905 Bedienungsanleitung

Cisco

Cisco 6901 Standard Bedienungsanleitung

Cisco

Cisco SPA 303 Series Bedienungsanleitung

Cisco

Cisco 8832 Bedienungsanleitung

Cisco

Cisco Cisco 7960 Bedienungsanleitung

Cisco

Cisco 7942 Bedienungsanleitung

Cisco

Cisco CP-7962G Bedienungsanleitung

Cisco

Cisco SPA 303 Series Bedienungsanleitung

Cisco

Cisco 7800 Series Bedienungsanleitung

Cisco

Cisco 8841 Bedienungsanleitung

Cisco

Cisco 7965 Bedienungsanleitung

Cisco

Cisco 6851 Bedienungsanleitung

Cisco

Cisco 7841 Bedienungsanleitung

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco 7800 Series Bedienungsanleitung

Cisco

Cisco IP 7975 Series Bedienungsanleitung

Cisco

Cisco IP 7960G Bedienungs- und Sicherheitshinweise

Cisco

Cisco 6825 Bedienungsanleitung

Cisco

Cisco 6800 Series Bedienungsanleitung

Cisco

Cisco 8800 Series Bedienungsanleitung

Cisco

Cisco Small Business Pro SPA 504G Bedienungsanleitung

Cisco

Cisco Cisco 7960 Bedienungsanleitung

Cisco

Cisco 7905 Bedienungsanleitung

Cisco

Cisco 7945G - Unified IP Phone VoIP Bedienungsanleitung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Fanvil

Fanvil X4 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Yealink

Yealink SIP-T52S Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Bedienungsanleitung

Nortel

Nortel i2050 Bedienungsanleitung

Fiberme

Fiberme FAP260 Series Bedienungsanleitung