Cisco 8832 Leitfaden

Maintenance

•Basic Reset, on page 1

•Voice Quality Monitoring, on page 4

•Voice Quality Reporting, on page 5

•Cisco IP Phone Cleaning, on page 7

•View Phone Information, on page 7

•Reboot Reasons, on page 7

Basic Reset

Performing a basic reset of a Cisco IP Phone provides a way to recover when the phone experiences an error.

The reset provides a way to reset or restore various configuration and security settings.

When you set up emergency calls, the phone requests an updated location whenever a person performs a

phone restart.

Note

The following table describes the ways to perform a basic reset. You can reset a phone with any of these

operations after the phone has started up. Choose the operation that is applicable for your situation.

Table 1: Basic Reset Methods

ExplanationActionOperation

Resets any user and network setup

changes that you have made, to the

previously saved settings that the

phone has not written to its flash

memory. The phone then restarts.

Restart phone

Restores the phone configuration

or settings to factory default.

Reset settings

Maintenance

When an administrator has set up emergency calls, the phone requests an updated location whenever the

administrator does the following actions:

• Registers the phone with the call server.

• Restarts the phone (phone is registered).

• Changes the network interface that is used for the SIP registration.

• Changes the IP address of the phone.

Note

Perform a Factory Reset with the Phone Keypad

Use these steps to reset the phone to factory default settings using the phone keypad.

Procedure

Step 1 Unplug the phone:

• If using PoE, unplug the LAN cable.

• If using the power cube, unplug the power cube.

Step 2 Wait 5 seconds.

Step 3 Press and hold #and plug the phone back in.

When the phone boots up, the light on the mute button lights up.

Step 4 Press the 123456789*0# keys in sequence.

When you press a key, the light on the mute button flashes.

After you press these buttons, the phone goes through the factory reset process.

If you press the buttons out of sequence, the phone powers on normally.

Do not power down the phone until it completes the factory reset process, and the main screen appears.

Caution

Perform Factory Reset from Phone Menu

Procedure

Step 1 Press Settings.

Step 2 Select Device administration >Factory reset.

Maintenance

Perform a Factory Reset with the Phone Keypad

Step 3 To restore phone configuration or settings to factory default, press OK.

Factory Reset the Phone from Phone Web Page

You can restore your phone to its original manufacturer settings from the phone web page. After you reset

the phone, you can reconfigure it.

Procedure

Reset your phone from the phone web page from one of the methods:

• Enter the URL in a supported web browser and click Confirm Factory Reset.

You can enter URL in the format:

http://<Phone IP>/admin/factory-reset

where:

Phone IP = actual IP address of your phone.

/admin = path to access admin page of your phone.

factory-reset = command that you need to enter in the phone web page to factory-reset your phone.

• On the phone web page, select Admin Login >Advanced >Info >Debug Info.Click Factory Reset

in the Factory Reset section and confirm the factory reset message in the next screen. Click Submit All

Changes.

Identify Phone Issues with a URL in the Phone Web Page

When the phone doesn't work or doesn't register, a network error or any misconfiguration might be the cause.

To identify the cause, add a specific IP address or a domain name to the phone admin page. Then, try to access

so that the phone can ping the destination and display the cause.

Procedure

In a supported web browser, enter a URL that consists of your phone IP address and the destination IP that

you want to ping. Enter the URL using the format:

http:/<Phone IP>/admin/ping?<ping destination>, where:

<Phone IP> = actual IP address of your phone.

/admin = path to the access admin page of your phone.

<ping destination> = any IP address or domain name that you want to ping.

Maintenance

Factory Reset the Phone from Phone Web Page

The ping destination allows only alphanumeric characters, ‘-’, and “_” (underscores). Otherwise the phone

shows an error on the web page. If the <ping destination> includes spaces, the phone uses only the first part

of the address as the pinging destination.

For example, to ping the 192.168.1.1 address:

http://<Phone IP>/admin/ping?192.168.1.1

Voice Quality Monitoring

To measure the voice quality of calls that are sent and received within the network, Cisco IP Phones use these

statistical metrics that are based on concealment events. The DSP plays concealment frames to mask frame

loss in the voice packet stream.

• Concealment Ratio metrics—Show the ratio of concealment frames over total speech frames. An interval

conceal ratio is calculated every 3 seconds.

• Concealed Second metrics—Show the number of seconds in which the DSP plays concealment frames

due to lost frames. A severely “concealed second” is a second in which the DSP plays more than five

percent concealment frames.

Concealment ratio and concealment seconds are primary measurements based on frame loss. A Conceal Ratio

of zero indicates that the IP network is delivering frames and packets on time with no loss.

Note

You can access voice quality metrics from the Cisco IP Phone using the Call Statistics screen or remotely by

using Streaming Statistics.

Voice Quality Troubleshooting Tips

When you observe significant and persistent changes to metrics, use the following table for general

troubleshooting information.

Table 2: Changes to Voice Quality Metrics

ConditionMetric Change

Network impairment from packet loss or high jitter.Conceal Ratio and Conceal Seconds increase

significantly

Maintenance

Voice Quality Monitoring

ConditionMetric Change

• Noise or distortion in the audio channel such as

echo or audio levels.

• Tandem calls that undergo multiple

encode/decode such as calls to a cellular network

or calling card network.

•Acoustic problems coming from a speakerphone,

handsfree cellular phone or wireless headset.

Check packet transmit (TxCnt) and packet receive

(RxCnt) counters to verify that voice packets are

flowing.

Conceal Ratio is near or at zero, but the voice quality

is poor.

Network impairment from packet loss or high jitter

levels:

• Average MOS LQK decreases may indicate

widespread and uniform impairment.

• Individual MOS LQK decreases may indicate

bursty impairment.

Cross-check the conceal ratio and conceal seconds

for evidence of packet loss and jitter.

MOS LQK scores decrease significantly

• Check to see if the phone is using a different

codec than expected (RxType and TxType).

• Check to see if the MOS LQK version changed

after a firmware upgrade.

MOS LQK scores increase significantly

Voice quality metrics do not account for noise or distortion, only frame loss.

Note

Voice Quality Reporting

You can capture voice quality metrics for Voice over Internet Protocol (VoIP) sessions with a Session Initiation

Protocol (SIP) event package. Voice call quality information derived from RTP and call information from

SIP is conveyed from a User Agent (UA) in a session (reporter) to a third party (collector).

The Cisco IP phone uses User Datagram Protocol (UDP) to send a SIP PUBLISH message to a collector

server.

Supported Scenarios for Voice Quality Reporting

Currently, only the basic call scenario supports voice quality reporting. A basic call can be a peer to peer

incoming or outgoing call. The phone supports periodic SIP publish message.

Maintenance

Voice Quality Reporting

Mean Opinion Scores and Codecs

The voice quality metrics use Mean Opinion Score (MOS) to rate the quality. A MOS rating of 1 is the lowest

quality; a MOS rating of 5 is the highest quality. The following table gives a description of some of the codecs

and MOS scores. The phone supports all codecs. For all codecs, the phone sends the SIP Publish message.

Minimum Call Duration for

Valid MOS Value

MOSComplexity and DescriptionCodec

10 secondsA minimum value of 4.1 indicates good

voice quality.

Very low complexity.

Supports uncompressed 64

kbps digitized voice

transmission at one to ten 5

ms voice frames-per-packet.

This codec provides the

highest voice quality and

uses the most bandwidth of

any of the available codecs.

G.711

(A-law

and

u-law)

30 secondsA minimum value of 3.5 indicates good

voice quality.

Low to medium complexity.G.729A

30 secondsA minimum value of 3.5 indicates good

voice quality.

Contains the same reduced

complexity modifications

present in the G.729A.

G.729AB

Configure Voice Quality Reporting

You can enable voice quality reporting on the phone with the web interface. Each extension on a phone has

a separate voice quality report. For each extension on the phone, use the corresponding Voice Quality Report

Address field to configure the generation of voice quality report.

Procedure

Step 1 On the Phone Web page, select Admin Login >advanced >Voice >Ext x.

Where:

• Ext x = the extension number on the phone

Step 2 In SIP Settings, enter a value in the Voice Quality Report Address x field. You can enter either a domain

name or an IP address in this field.

You can also add a port number along with the domain name or an IP address in this field. If you do not enter

a port number, the value of the SIP UDP Port (5060) is used by default. If the collector server URL parameter

is blank, a SIP PUBLISH message is not sent out.

Step 3 Click Submit All Changes.

Maintenance

Mean Opinion Scores and Codecs

Cisco IP Phone Cleaning

To clean your Cisco IP Phone, use only a dry soft cloth to gently wipe the phone and the phone screen. Do

not apply liquids or powders directly to the phone. As with all non-weatherproof electronics, liquids and

powders can damage the components and cause failures.

When the phone is in sleep mode, the screen is blank and the Select button is not lit. When the phone is in

this condition, you can clean the screen, as long as you know that the phone will remain asleep until after you

finish cleaning.

View Phone Information

Procedure

To check the current status of the Cisco IP Phone, click the Info tab.

The Info tab shows information about all phone extensions, including phone statistics and the registration

status.

Reboot Reasons

The phone stores the most recent five reasons that the phone was refreshed or rebooted. When the phone is

reset to factory defaults, this information is deleted.

The following table describes the reboot and refresh reasons for the Cisco IP Phone.

DescriptionReason

The reboot was a result of an upgrade operation

(regardless whether the upgrade completed or failed).

Upgrade

The reboot was the result of changes made to

parameter values by using the IP phone screen or

phone web user interface, or as a result of

synchronization.

Provisioning

The reboot was triggered by a SIP request.SIP Triggered

The reboot was triggered as a result of remote

customization.

The user manually triggered a cold reboot.User Triggered

The reboot was triggered after the phone IP address

changed.

IP Changed

Maintenance

Cisco IP Phone Cleaning

You can view the reboot history as follows:

• From the phone web user interface

• From the IP phone screen

• From the phone Status Dump file (http://phoneIP/status.xml or http://phoneIP/admin/status.xml)

Reboot History on the Phone Web User Interface

On the Info >System Status page, the Reboot History section displays the device reboot history, the five

most recent reboot dates and times, and a reason for the reboot. Each field displays the reason for the reboot

and a time stamp that indicates when the reboot took place.

For example:

Reboot Reason 1: [08/13/14 06:12:38] User Triggered

Reboot Reason 2: [08/10/14 10:30:10] Provisioning

Reboot Reason 3: [08/10/14 10:28:20] Upgrade

The reboot history displays in reverse chronological order; the reason for the most recent reboot displays in

Reboot Reason 1.

Reboot History on the Cisco IP Phone Screen

Reboot History is located under Apps >Admin Settings >Status menu. In the Reboot History window, the

reboot entries displays in reverse chronological order, similar to the sequence that displays on the phone web

user interface.

Reboot History in the Status Dump File

The reboot history is stored in the Status Dump file (http://<phone_IP_address>/admin/status.xml).

In this file, tags Reboot_Reason_1 to Reboot_Reason_3 store the reboot history, as shown in this example:

<Reboot_History>

<Reboot_Reason_1>[08/10/14 14:03:43]Provisioning</Reboot_Reason_1>

<Reboot_Reason_2>[08/10/14 13:58:15]Provisioning</Reboot_Reason_2>

<Reboot_Reason_3>[08/10/14 12:08:58]Provisioning</Reboot_Reason_3>

<Reboot_Reason_4>

<Reboot_Reason_5>

<Reboot_History/>

Maintenance

Reboot History on the Phone Web User Interface

Andere Handbücher für 8832

Inhaltsverzeichnis

Andere Cisco IP-Telefon Handbücher

Cisco

Cisco 7965G - Unified IP Phone VoIP Bedienungsanleitung

Cisco

Cisco SPA300 Series Referenzhandbuch

Cisco

Cisco Unified 6921 Bedienungsanleitung

Cisco

Cisco DATAVOX 7941 Bedienungsanleitung

Cisco

Cisco MCS 7800 Series Bedienungsanleitung

Cisco

Cisco 7941G-GE - IP Phone VoIP Bedienungsanleitung

Cisco

Cisco 8831 Bedienungsanleitung

Cisco

Cisco 8865 Bedienungsanleitung

Cisco

Cisco Unified 8961 Bedienungsanleitung

Cisco

Cisco SPA504 Bedienungsanleitung

Cisco

Cisco 6800 Series Bedienungsanleitung

Cisco

Cisco 7931G - Unified IP Phone VoIP Bedienungsanleitung

Cisco

Cisco MCS 7800 Series Bedienungsanleitung

Cisco

Cisco Small Business SPA525G2 Bedienungsanleitung

Cisco

Cisco 6941 - Unified IP Phone Slimline VoIP Bedienungsanleitung

Cisco

Cisco LINKSYS one PHM1200 Bedienungsanleitung

Cisco

Cisco 7961G - IP Phone VoIP Bedienungsanleitung

Cisco

Cisco Linksys One PHB1100 Bedienungsanleitung

Cisco

Cisco SPA525G - Small Business Pro IP Phone VoIP Bedienungsanleitung

Cisco

Cisco Cisco Unified IP Phone 7960G Bedienungsanleitung

Cisco

Cisco 8800 Series Bedienungsanleitung

Cisco

Cisco 7975G - Unified IP Phone VoIP Bedienungsanleitung

Cisco

Cisco 6800 Series Bedienungsanleitung

Cisco

Cisco Small Business SPA922 Bedienungsanleitung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Fanvil

Fanvil X4 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Yealink

Yealink SIP-T52S Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Bedienungsanleitung

Nortel

Nortel i2050 Bedienungsanleitung

Fiberme

Fiberme FAP260 Series Bedienungsanleitung