Cisco SPA 303 Bedienungsanleitung
0800 040 8888
Quick Start Guide to Your IP Phone
SPA 300 Series IP Phone
Models SPA 301 and SPA 303
• SPA 300 Series IP phone
• Phone stand
• RJ-45 Ethernet cable
• Quick start guide
• Product CD-ROM
working with daisy
www.daisygroupplc.com
v1 - 06/13
Welcome
Before you begin
Getting to know your Cisco SPA 301 IP Phone
Thank you for choosing the Cisco SPA 300 Series IP Phone. This guide describes how to
physically install your Cisco SPA 300 Series IP Phone and how to perform some basic tasks.
Make sure that your internet telephony service is configured and active. For example, your phone
will be registered to a device, such as a Cisco Unified Communications 500 Series or a third-party
application server, that provides your phone service.
# Phone feature Description
1Receiver Pick up to place or answer a call.
2Message
waiting/status
indicator
The LED colour indicates the phone or
message status. A solid red LED indicates that
you have a new voicemail message.
3Ringer button Push to turn ringer on or off.
4Voicemail button Press to access voicemail (this must be set up
by your phone administrator).
5Flash button Press to place a call on hold and open another
line.
6Redial button Press to redial the last number called.
7Volume Press repeatedly to increase the volume of
the handset when the receiver is off the hook,
or the ringer volume when the receiver is in
place.
8Keypad Use to dial phone numbers.
0800 040 8888
working with daisy
www.daisygroupplc.com
v1 - 06/13
Installing the Cisco SPA
301 IP Phone
Step 1 Turn the phone body over to expose
the ports on the back of the unit.
Step 2 Insert the long end of the phone cord
into the handset port on the phone
body that is marked with a phone
symbol (labelled 2).
Step 3 Insert the other end of the phone
cord into the port at the bottom of
the receiver.
Step 4 Connect your phone to the network
using one of the methods below:
• Using an Ethernet connection
Insert one end of the Ethernet cable into the
network port on the phone body marked ‘WAN’
(labelled 3).
Insert the other end of the Ethernet cable into
the appropriate device, such as a network
switch, on your network.
• Using a wireless connection
You can use a Cisco WBP54G Wireless-G
Bridge with the IP phone to create a wireless
connection between the phone and the network.
See the WBP54G documentation on
www.cisco.com for more information.
Step 5 Insert one end of the power cord
into an outlet and insert the other end
of the power cord into the power port
on the phone body (labelled 1).
NB To power the phone through the Ethernet
connection, use the optional Cisco POES5
5-Volt Power Over Ethernet Splitter accessory.
See the Cisco POES5 documentation on
www.cisco.com for more information.
Step 6 (Optional) To install the phone on a
vertical surface, use the Cisco MB100
Wall Mount bracket. See the Cisco
Small Business IP Phone SPA 300
Series User Guide (SIP) or the Cisco
Unified Communications Manager
Express for the Cisco Small Business
IP Phone SPA 300 Series documents
on www.Cisco.com for more information.
After your phone is successfully connected to the
network and receives a basic configuration, you
should hear a dial tone when picking up the receiver.
0800 040 8888
working with daisy
www.daisygroupplc.com
v1 - 06/13
Getting to know the Cisco SPA
303 IP Phone
# Phone feature Description
1Receiver Pick up to place or answer a call.
2Message waiting
indicator
Displays solid red when you have a new voicemail message. Flashes red during an incoming call
or when the phone’s firmware is being updated.
3LCD screen Displays date and time, phone station name, line extensions, and soft key options.
4Line keys Indicates phone line status - see below for colour codes.
5Soft key buttons Press a soft key button to perform the action shown on the label on the LCD screen above. Soft
keys vary depending on your phone system. See your phone user guide for more information.
6Navigation buttons Press an arrow to scroll left, right, up or down through items shown on the LCD screen.
7Messages button Press repeatedly to increase the volume of the handset (when the receiver is off the hook) or
ringer volume (when the receiver is in place).
8Hold button Press to access voicemail (must be set up by your phone system administrator).
9Set-up button Press to access a menu to configure features and preferences (such as your directory and speed
dials), access your call history, and set up functions (such as call forwarding).
10 Mute button Press to mute or unmute the phone. When the phone is muted, the button glows red. A flashing
mute button indicates the network connection cannot be found.
11 Headset button Push to turn the headset on or off. When the headset is on, the button glows green.
12 Volume button Press '+' to increase the volume and '-' to lower the volume of the handset, headset, speaker
(when the receiver is off the phone), or ringer volume (when the receiver is on the phone).
13 Speaker button Push to turn the speaker on or off. When the speaker is on, the button glows green.
14 Keypad Use to dial phone numbers, enter letters and choose menu items.
Line key colour codes
Green - Line is idle
Red (steady) - Line is active or in use
Red (blinking) - Line is on hold
Orange - Line is unregistered and cannot be used
Note - Line key colours depend on your phone system
and can vary.
These keys can also be programmed by your phone
system administrator to perform functions such as
speed dial, call pickup, or monitoring and extension.
0800 040 8888
working with daisy
www.daisygroupplc.com
v1 - 06/13
Step 1 Turn the phone body over to expose the ports
on the back of the unit.
Step 2 Insert the long end of the phone cord into
the receiver port on the phone body that is
marked with a phone symbol (labelled 5).
Step 3 (Optional) Route the phone cord through
the cable slot (labelled 4).
Step 4 Insert the other end of the phone cord into
the port at the bottom of the receiver.
Step 5 Connect the phone stand by lining up the
tabs on the stand with the slots on the phone
body. Slide the bottom tabs into the lower
slots on the phone body (labelled 1) and
lightly press down on the stand. It should
easily slide into the upper stand slots.
Do not force.
Installing the Cisco SPA
303 IP Phone
Step 6 Connect your phone to the network using
one of the methods below:
• Using an Ethernet connection
Insert one end of the Ethernet cable into the
network port on the phone body marked ‘SW’
(labelled 3).
Insert the other end of the Ethernet cable into
the appropriate device, such as a network
switch, on your network.
• Using a wireless connection
You can use a Cisco WBP54G Wireless-G
Bridge with the IP phone to create a wireless
connection between the phone and the
network. See the WBP54G documentation on
www.cisco.com for more information.
Step 7 Insert one end of the power cord into an
outlet and insert the other end of the
power cord into the power port on the
phone body (labelled 6).
NB To power the phone through the Ethernet
connection, use the optional Cisco POES5
5-Volt Power Over Ethernet Splitter accessory.
See the Cisco POES5 documentation on
www.cisco.com for more information.
Step 8 (Optional) To provide network access to
a PC, connect one end of an additional
Ethernet cable (not provided) to the PC
port on the back of the phone body
(labelled 2). Connect the other end of the
Ethernet cable to the network port on
your PC.
0800 040 8888
working with daisy
www.daisygroupplc.com
Use these steps to install the phone and connect it to your network.
v1 - 06/13
After your phone is successfully connected to the network and receives a
basic configuration, you should hear a dial tone when picking up the receiver
or pressing the speaker phone button, and your phone line keys should glow
green (depending on your phone system).
Using your IP phone
Placing or answering calls
Pick up the receiver and dial (SPA 301/303), or press the speaker or headset button (SPA 303).
Putting a call on hold
To put a call on hold, press the Flash (SPA 301) or Hold (SPA 303) button. The caller hears a
series of three rapid beeps or music while on hold. To resume the call, press Flash (SPA 301) or
the flashing red line button for the call (SPA 303).
Ending a call
If you are using the receiver, hang up (SPA 301/303). If you are using the speakerphone function
(SPA 303), press the speaker button. If you are using the headset (SPA 303), press the headset button.
0800 040 8888
working with daisy
www.daisygroupplc.com
v1 - 06/13
Andere Handbücher für SPA 303
5
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Cisco IP-Telefon Handbücher
Cisco
Cisco 8941 Bedienungsanleitung
Cisco
Cisco 7942 Einrichtungshandbuch
Cisco
Cisco 7942G - Unified IP Phone VoIP Bedienungsanleitung
Cisco
Cisco IP 7940 Bedienungsanleitung
Cisco
Cisco 504 Service-Handbuch
Cisco
Cisco SPA50 Series Bedienungsanleitung
Cisco
Cisco 3911 Bedienungsanleitung
Cisco
Cisco Small Business Pro SPA 504G Bedienungsanleitung
Cisco
Cisco SPA504 Bedienungsanleitung
Cisco
Cisco 8811 Bedienungsanleitung
Cisco
Cisco Unified 6921 Bedienungsanleitung
Cisco
Cisco Meraki MC74 Bedienungsanleitung
Cisco
Cisco 7925G - Unified Wireless IP Phone VoIP Bedienungsanleitung
Cisco
Cisco SPA525G - Small Business Pro IP Phone VoIP Bedienungsanleitung
Cisco
Cisco 7962 Bedienungsanleitung
Cisco
Cisco Unified 6921 Bedienungsanleitung
Cisco
Cisco DATAVOX 7941 Bedienungsanleitung
Cisco
Cisco 8841 Bedienungsanleitung
Cisco
Cisco 524SG - Unified IP Phone VoIP Bedienungsanleitung
Cisco
Cisco Cisco 7940 Bedienungsanleitung
