Cisco Unified 8961 Bedienungsanleitung

CHAPTER

5-1

Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.0 (SIP)

OL-20862-01

Setting Up the Cisco Unified Video Camera

The Cisco Unified IP Phone 9951 and 9971 supports the add-on accessory Cisco Unified Video Camera.

The Cisco Unified Video Camera connects to your Cisco Unified IP Phone and allows you to make a

point-to-point video call with another Cisco Unified IP Phone with a Cisco Unified Video Camera

attached. If a phone does not have a Cisco Unified Video Camera attached, it can only receive one-way

video.

This chapter contains the following information:

•Configuring the Cisco Unified Video Camera, page 5-1

•Attaching the Cisco Unified Video Camera, page 5-2

•Adjusting the Camera Settings, page 5-2

•Post-Installation Steps, page 5-4

•Using the Cisco Unified Video Camera, page 5-4

Configuring the Cisco Unified Video Camera

To configure the Cisco Unified Video Camera, you must perform the following configuration steps in

Cisco Unified Communications Manager administration:

Note The parameters described in the following procedure can be enabled on either the Phone Configuration

window (Device > Phone), the Enterprise Phone Configuration window (System > Enterprise Phone

Configuration), or the Common Phone Profile window (Device > Device Settings > Common Phone

Profile). Be sure to also check the corresponding Override Common Settings parameter in the

configuration window. The Phone Configuration window is referenced below for purposes of the

procedure description.

For more information about parameters that can be configured in any of these three configuration

windows, see the “Configuring Product Specific Configuration Parameters” section on page 8-20.

Procedure

Step 1 In the phone configuration window (Device > Phone) of the phone to which you are adding the Cisco

Unified Video Camera, enable the Cisco Camera parameter. This field is located in the Product Specific

Configuration layout portion of the window.

5-2

Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.0 (SIP)

OL-20862-01

Chapter 5 Setting Up the Cisco Unified Video Camera

Attaching the Cisco Unified Video Camera

Step 2 On the same window, enable the Video Capabilities parameter.

Step 3 Click Save.

Attaching the Cisco Unified Video Camera

To install the Cisco Unified Video Camera, you can either:

•Attach the camera to your phone.

•Attach the camera to your computer monitor (or to another object in your work area).

The USB port connector on the bottom of the Cisco Unified Video Camera attaches to the back port (not

the side port) on the Cisco Unified IP Phone 9951 or 9971. As you attach the USB connector to the back

port on the phone, the camera should slide easily into the camera pin holes on the phone.

Figure 3-4 on page 3-15 shows the location of the back USB port and the camera pin holes for the Cisco

Unified IP Phone 9951. Figure 3-6 on page 3-17 shows the location of the back USB port and the camera

pin holes for the Cisco Unified IP Phone 9971.

Installation Procedure

For the complete installation procedure, see the Cisco Unified Video Camera Quick Start Guide at this

location:

http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/9971_9951_8961/8_0/english/user/qsg/qs99

camen80.pdf

Adjusting the Camera Settings

Once you have attached the camera on your phone, you can control the features of the camera.

This section provides information on the features you can control from the phone:

•Adjusting the Camera View Area, page 5-2

•Adjusting the Brightness Setting, page 5-3

•Adjusting Auto Transmit Setting, page 5-3

Adjusting the Camera View Area

The View Area feature acts as a wide angle and zoom function for your camera and allows you to adjust

the view area that is shared during video streaming. The View Area feature acts as a wide angle and zoom

function for your camera.

To adjust the camera view area, follow these steps:

Procedure

Step 1 On the Cisco Unified IP Phone, press the Applications button .

Step 2 Select Accessories.

5-3

Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.0 (SIP)

OL-20862-01

Chapter 5 Setting Up the Cisco Unified Video Camera

Adjusting the Camera Settings

Step 3 Highlight Cisco Unified Camera.

Step 4 Press the Set-up softkey.

Step 5 Select View Area.

Step 6 Use the arrows on the Navigation pad to increase or decrease the view area.

Step 7 Press the Save softkey.

Adjusting the Brightness Setting

The Brightness setting affects the video that you transmit to others. However, it does not affect the video

that you receive from other parties. You can adjust the brightness setting to improve the quality of the

video during streaming.

Note As the field of view can affect brightness, adjust the View Area feature for your camera before adjusting

the Brightness setting.

To adjust the Brightness setting, follow these steps:

Procedure

Step 1 On the Cisco Unified IP Phone, press the Applications button .

Step 2 Select Accessories.

Step 3 Highlight Cisco Unified Camera.

Step 4 Press the Set-up softkey.

Step 5 Select Brightness.

Step 6 Use the arrows on the Navigation pad to increase or decrease brightness.

Step 7 Press the Save softkey.

Adjusting Auto Transmit Setting

The Auto Transmit feature allows you to control the streaming of videos for both inound and outbound

calls.

When Auto Transmit is on (default setting), the camera streams video automatically during calls.

When Auto Transmit is off, video for each call is automatically muted (however, your phone still

receives video). To resume video transmission in this case, press the Unmute Video softkey .

To turn the Auto Transmit setting on or off, follow these steps:

Procedure

Step 1 On the Cisco Unified IP Phone, press the Applications button .

5-4

Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 8.0 (SIP)

OL-20862-01

Chapter 5 Setting Up the Cisco Unified Video Camera

Post-Installation Steps

Step 2 Select Accessories.

Step 3 Highlight Cisco Unified Camera.

Step 4 Press the Set-up softkey.

Step 5 Press the Turn On or Turn Off softkey.

Post-Installation Steps

After installing the Cisco Unified Video Camera, perform the following checks:

1. Wait till the “camera ready” message appears.

Note The camera may need to upgrade after installation. This may take a few minutes before the

camera is operational.

2. Press the Video Preview softkey to check the picture quality.

–

If the video preview image looks too blue, try increasing the camera Brightness setting.

–

If the background looks washed out, try decreasing the camera Brightness setting.

Note For information about adjusting camera settings on the phone, see the Cisco Unified Video

Camera Quick Start Guide at this location:

http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/9971_9951_8961/8_0/english/u

ser/qsg/qs99camen80.pdf

3. Move the phone/camera to a position where there are no bright lights in the field of view.

4. Move the phone/camera so that the user is illuminated by light coming from the front.

Using the Cisco Unified Video Camera

For information about placing and receiving video calls, setting up video conferences, and adjusting

camera settings on the phone, see the Cisco Unified Video Camera Quick Start Guide at this location:

http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/9971_9951_8961/8_0/english/user/qsg/qs99

camen80.pdf

Andere Handbücher für Unified 8961

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco IP-Telefon Handbücher

Cisco

Cisco 7906G - Unified IP Phone VoIP Bedienungsanleitung

Cisco

Cisco 6945 Series Bedienungsanleitung

Cisco

Cisco 9971 Standard Bedienungsanleitung

Cisco

Cisco 7965G - Unified IP Phone VoIP Bedienungsanleitung

Cisco

Cisco 8821 Bedienungsanleitung

Cisco

Cisco 7945 Series Bedienungsanleitung

Cisco

Cisco Small Business SPA 301 Bedienungsanleitung

Cisco

Cisco DATAVOX 7941 Bedienungsanleitung

Cisco

Cisco 7931G - Unified IP Phone VoIP Referenzhandbuch

Cisco

Cisco MCS 7800 Series Bedienungsanleitung

Cisco

Cisco 7911G - IP Phone VoIP Bedienungs- und Wartungshandbuch

Cisco

Cisco 9951 Standard Bedienungsanleitung

Cisco

Cisco 7841 Technisches Datenblatt

Cisco

Cisco 8945 Bedienungsanleitung

Cisco

Cisco 504 Bedienungsanleitung

Cisco

Cisco DATAVOX 7941 Bedienungsanleitung

Cisco

Cisco 7925G - Unified Wireless IP Phone VoIP Bedienungsanleitung

Cisco

Cisco SPA300 Series Bedienungsanleitung

Cisco

Cisco 7861 Bedienungsanleitung

Cisco

Cisco 7931G - Unified IP Phone VoIP Bedienungsanleitung

Cisco

Cisco 7811 Bedienungsanleitung

Cisco

Cisco Catalyst 4000 Bedienungsanleitung

Cisco

Cisco 521SG - Unified IP Phone VoIP Bedienungsanleitung

Cisco

Cisco Unified 8961 Anleitung zur Verwendung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Fanvil

Fanvil X4 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Yealink

Yealink SIP-T52S Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Bedienungsanleitung

Nortel

Nortel i2050 Bedienungsanleitung

Fiberme

Fiberme FAP260 Series Bedienungsanleitung