Cisco TelePresence VCR MSE 8220 Bedienungsanleitung

Cisco TelePresence

VCR MSE 8220

Getting started

61-0008-05

Contents

General information ................................................................................................................ 3

About the Cisco TelePresence VCR MSE 8220 .................................................. 3

Port and LED location ................................................................................................ 3

LED behavior ................................................................................................................ 4

Installing the VCR MSE 8220 ................................................................................................ 6

Step one: Install the VCR MSE 8220 into the MSE 8000 chassis ................. 6

Step two: Allocate port licences ............................................................................ 8

Step two: Connect to Ethernet Port A ................................................................. 8

Initial configuration ................................................................................................................. 9

Step one: Configure Ethernet Port A settings .................................................. 9

Step two: Assign an IP address to the VCR MSE 8220 .................................... 9

Configuring the VCR MSE 8220 .........................................................................................10

Step one: Log in to the blade ...............................................................................10

Step two: Using an H.323 gatekeeper or SIP registrar (optional) ............10

Step three: Add endpoints (optional) ................................................................11

Using the VCR MSE 8220 ......................................................................................................12

Checking for updates ..............................................................................................13

Troubleshooting and technical support information ...............................................14

Using the event log to help solve a problem ..................................................14

Getting more help ....................................................................................................14

Disclaimers and notices ........................................................................................................15

General information

About the Cisco TelePresence VCR MSE 8220

The Cisco TelePresence VCR MSE 8220 (VCR MSE 8220) uses the latest purpose-

built technology to record video and data from standard video conferencing

equipment. The recordings can be streamed live or played back on demand at

multiple bit rates to a PC or any video conferencing endpoint.

Port and LED location

Figure 1 shows the position of ports and LEDs on the VCR MSE 8220.

Figure 1: VCR MSE 8220 front panel

Cisco VCR MSE 8220

Disk Activity

Status

Alarm

Recording

Ethernet Port

Status LEDs

System Load LEDs

Status LED

Compact Flash

Activity LED

Console Port

Alarm LED

Power LED

Ethernet ports

Hard Disk Hard Disk

Activity LED Recording LED

General information

LED behavior

Table 1 describes the behavior of the LEDs.

Table 1: VCR MSE 8220 LED behavior

LED Color Indicates

Compact Flash Activity Flashing

green

One of:

the VCR MSE 8220 is booting

a configuration change has been

made

the configuration is being

transferred by FTP

Status Green The VCR MSE 8220 is operating

normally

Alarm Red The VCR MSE 8220 is booting or has

developed a fault, for example:

temperature is outside normal

limits

battery failure of the internal clock

Refer to the web interface for more

information about the problem (go to

Status > Health)

Hard Disk Activity Flashing

green

The VCR MSE 8220 is reading from or

writing to its hard disk

Hard Disk Recording Red The VCR MSE 8220 is recording

General information

System Load Green The VCR MSE 8220 is processing

conference data. The LEDs represent

the media processing load of the blade.

The column numbered 1 represents

audio load. The other columns represent

video DSP load. Media processing load

is also displayed in the web interface: go

to Status > General

Ethernet Port Status, for each

Ethernet port:

FDX Green The link has been negotiated as a full-

duplex link

Act Green Packets are being transmitted on this

port

Link Green The speed of the link from this port,

which is either 10, 100, or 1000 Mbps

Power Blue The VCR MSE 8220 is receiving power

from the MSE 8000 chassis

Table 1: VCR MSE 8220 LED behavior (continued)

LED Color Indicates

Installing the VCR MSE 8220

For information about powering the MSE 8000, refer to the Getting Started Guide on

http://www.tandberg.com/support/video-conferencing-documentation.jsp).

Step one: Install the VCR MSE 8220 into the MSE 8000 chassis

1 Remove the blade or blanking blade from the slot into which you are going to

install the VCR MSE 8220:

i Using a No.1 Phillips screwdriver, loosen the screws in the retaining latches

with an anti-clockwise quarter turn.

ii Open both retaining latches on the front of the blade or blanking blade.

When open, a retaining latch is at a 90° angle perpendicular to the front of

the blade.

iii Slide out the blade or blanking blade.

2 Open both retaining latches on the front of the VCR MSE 8220. When open, a

retaining latch is at a 90° angle perpendicular to the front of the blade.

3 Slide the VCR MSE 8220 into the blade slot (as shown in Figure 2) until it stops.

IMPORTANT: Before installing the VCR MSE 8220 into the MSE 8000,

you must read the safety information for the MSE 8000 chassis at:

http://www.cisco.com/go/telepresence/safety.

Although blades are hot-swappable parts, you must only remove one

blade at any time. Remove the power from the MSE 8000, if you need to

remove more than one blade at a time.

Before hot-swapping a blade, shut down the blade using the web interface.

Do not shut down a blade during a software upgrade or if the blade is

processing.

You must install either a blade or a blanking blade in each of the ten

positions in the chassis.

The Supervisor blade must be installed into slot 1 of the MSE 8000

chassis.

Installing the VCR MSE 8220

4 Simultaneously close both retaining latches on the blade (thereby engaging the

connectors at the rear of the blade) to secure it in the chassis as shown in

Figure 3.

5 Using a No.1 Phillips screwdriver, tighten the screws in the retaining latches

with a clockwise quarter turn.

Figure 2: Inserting a blade into the chassis

Installing the VCR MSE 8220

Figure 3: Closing the retaining latches on the front of a blade

Step two: Allocate port licences

Port licenses must be allocated to the VCR MSE 8220 from the Supervisor's Port

licenses page. Refer to the online help for assistance.

Step two: Connect to Ethernet Port A

Connect an Ethernet cable from Ethernet Port A to an Ethernet switch (rather than a

hub, to minimize interference from other devices on the network). The Ethernet

port is a 10/100/1000 Mbps auto-sensing connection.

Only connect to Ethernet Port B if you need to connect the VCR MSE

8220 to a second subnet.

Do not connect Ethernet Port A and Ethernet Port B to the same subnet.

Initial configuration

Step one: Configure Ethernet Port A settings

The default setting for the VCR MSE 8220 Ethernet ports is auto-sensing mode. If

the switch ports to which you connect the blade are not also set to auto-sensing

mode, then you need to configure the VCR MSE 8220 Ethernet ports to use the

same speed and duplex mode.

To configure Ethernet Port A, log in to the Supervisor’s web interface and go to

Hardware > Blades. For more information about configuring the port, refer to the

online help accessible from the Supervisor’s web interface.

Step two: Assign an IP address to the VCR MSE 8220

You can use the Supervisor’s web interface to configure the IP addresses of all blades

installed in the MSE 8000. Note that all blades are supplied with DHCP enabled. You

can either keep this setting or assign static IP addresses to a blade from the

Supervisor’s web interface. To view or configure the IP address of the blade, log in to

the Supervisor and go to Hardware > Blades. To access the web interface of the

VCR MSE 8220, go to Hardware > Blades and click the IP address of that blade.

Only connect to Ethernet Port B if you need to connect the VCR MSE

8220 to a second subnet.

Both ends of the Ethernet connection must be configured in the same

way. For example, either configure both ends of the link to be auto-

sensing or configure both ends to operate at the same speed and duplex.

To establish a 1000Mbps connection, both ends of the link must be

configured as auto-sensing.

Configuring the VCR MSE 8220

Step one: Log in to the blade

All administration of the VCR MSE 8220 is performed via the web interface.

To log in to the web interface of the VCR MSE 8220:

1 Log in to the Supervisor’s web interface.

2GotoHardware > Blades and click the IP address of the blade.

3Click

Click here to log in, and then click Change log in and enter the user

name admin with no password.

Step two: Using an H.323 gatekeeper or SIP registrar (optional)

Using an H.323 gatekeeper makes it easier for H.323 end-users to watch and make

recordings using directory numbers rather than requiring them to know the IP

address or host name of the blade. Likewise, a SIP registrar makes it easier for SIP

users to watch and make recordings.

To configure the blade to use an H.323 gatekeeper:

1 In the web interface of the VCR MSE 8220, go to Settings > Gatekeeper.

2Enable

H.323 gatekeeper usage and configure the settings you require, using

the online help for further assistance.

3Click

Apply changes.

To configure the blade to use a SIP registrar:

1 In the web interface, go to Settings > SIP.

2 Configure the settings you require, using the online help for further assistance.

3Click

Apply changes.

Cisco recommends that you change the admin account to use a password

as soon as possible. To do that, go to Users, click the admin link, and

provide the required user information.

Before you configure the VCR MSE 8220 to use, and register recordings

to, a SIP registrar, you must set up the blade and its recordings on that SIP

registrar.

Inhaltsverzeichnis

Andere Cisco Messgerät Handbücher

Cisco

Cisco MDS 9000 Series Kurzanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung