Cisco 5400 Bedienungsanleitung
Preparing for Installation
•Safety Recommendations and Warnings, on page 1
•Safety with Electricity, on page 1
•Site Requirements, on page 2
•Mounting Requirements, on page 4
•Power Guidelines and Requirements, on page 4
•Network Cabling Specification, on page 5
•Required Tools and Equipment, on page 5
Safety Recommendations and Warnings
Please read the following safety guidelines before you install this product:
• Review the safety warnings listed in Regulatory Compliance and Safety Information for the Cisco 5400
Enterprise Network Compute System before installing, configuring, or maintaining the device.
• Keep the chassis area clean and dust-free during and after installation.
• Keep the chassis in a safe place when you remove the chassis cover.
• Do not wear loose clothing that could get caught in the chassis.
• Wear safety glasses when working under conditions that might be hazardous to your eyes.
• Do not perform any action that creates a hazard to people or makes the equipment unsafe.
Safety with Electricity
Follow these general guidelines when working on equipment that is powered by electricity:
• Locate the emergency power-off switch in the room in which you are working. If an electrical accident
occurs, you can quickly turn off the power.
• Disconnect all power before doing the following:
• Installing or removing a chassis.
• Working near power supplies.
Preparing for Installation
1
• Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension
cables, frayed power cords, and missing safety grounds.
• Do not work alone if hazardous conditions exist.
• Never assume that power is disconnected from a circuit. Always check.
• Never open the enclosure of the internal power supply.
• If an electrical accident occurs, proceed as follows:
• Turn off power to the device.
• Call for help.
•Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate
action.
Follow these guidelines when working with any equipment that is disconnected from a power source but is
still connected to telephone wiring or other network cabling:
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically designed for it.
• Never touch uninsulated telephone wires or terminals unless the telephone line is disconnected at the
network interface.
• Use caution when installing or modifying telephone lines.
• Remove power cables from all installed power supplies before opening the chassis.
Always follow these electrostatic discharge (ESD) prevention procedures when removing and replacing
modules:
• Ensure that the router chassis is electrically connected to ground.
• Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to an
unpainted surface of the chassis frame to channel unwanted ESD voltages safely to ground. To guard
against ESD damage and shocks, the wrist strap and cord must operate effectively.
• If no wrist strap is available, ground yourself by touching a metal part of the chassis.
For the safety of your equipment, periodically check the resistance value of the anti-static strap. It should be
between 1 and 10 megohms (Mohm).
Caution
Site Requirements
Follow the general precautions listed below when installing or working with your device:
• Keep your system components away from radiators and heat sources.
• Do not block cooling vents.
Preparing for Installation
2
Preparing for Installation
Site Requirements
•Ensure that the chassis cover and module rear panels are secure. All empty network module slots, interface
card slots, and power supply bays must have filler panels installed. The chassis is designed to allow
cooling air to flow within it, through specially designed cooling slots. A chassis with uncovered openings
permits air leaks, which, in turn, may interrupt and reduce the flow of air across internal components.
• Baffles can help to isolate exhaust air from intake air, which also helps to draw cooling air through the
chassis. The best placement of the baffles depends on the airflow patterns in the rack, which can be found
by experimenting with different configurations.
• Do not spill food or liquid on any system components and do no operate in a wet environment.
• Do not push any objects into the openings of your system components. Doing so can cause fire or electric
shock by shorting out interior components.
• Route system cables, and the power supply cable and plug so that they cannot be stepped on or tripped
over. Be sure that nothing else rests on your system component cables or power cable.
• Do not modify power cables or plugs. Consult a licensed electrician or your power company for site
modifications. Always follow your local and national wiring rules.
• If you turn off your system, wait at least 30 seconds before turning it on again to avoid system component
damage.
Temperature, humidity, altitude, and vibration can affect the performance and reliability of the router. After
installation, ensure that the site maintains the environmental characteristics shown in this table:
MaximumMinimumEnvironmental Characteristic
40 degree C
(40 degrees C at 10,000
feet)
0 degree CSteady State Operating
+70 degrees C-20 degrees CStorage
90%10%Humidity operating (noncondensing)
95%5%Humidity nonoperating (noncondensing)
10,000 feet-500 feetAltitude operating: over allowable temperature range
(0 to 40 degrees C)
50,000 feet-1000 feetAltitude, nonoperating: over allowable temperature
range
+70 degrees C-25 degrees CThermal shock non-operating with change over time
of 3 minute
+40 degrees C0 degrees CThermal Shock - Operating at 2.5 degree C per minute
When an equipment that is installed in a rack (particularly in an enclosed rack) fails, try, if possible, to operate
the equipment in isolation. Power off other equipment in the rack (and in adjacent racks) to allow the equipment
to be tested in a condition that has maximum cool air and clean power.
Note
Preparing for Installation
3
Preparing for Installation
Site Requirements
Mounting Requirements
The height, width, depth and weight of the chassis are displayed in this table:
MeasurementCharacteristic
1.73 inches (4.39 cm) — 1RU rack-mountHeight
17.25 inches (43.815 cm) — 19 inch rack-mountWidth
13.8 inches (35.052 cm)
(including card handles and power supply handles)
Depth
13 lbs. (5.9 kg)Weight
To place the system in a proper location, it is necessary to know the dimensions of the device's chassis.
The Cisco 5400 ENCS can be placed on a desktop or installed in a rack. The mounting ears for the device are
designed for #12-24 UNC screws.
The location of your device and the layout of your equipment rack or wiring room are extremely important
considerations for proper operation. Equipment placed too close together, inadequate ventilation, and
inaccessible panels can cause malfunctions and shutdowns, and can make maintenance difficult. Plan for
access to both front and rear panels of the device.
This information can help you plan the rack configuration for your equipment:
• Allow clearance around the rack for maintenance.
• Allow at least one rack unit of vertical space between devices.
•Enclosed racks must have adequate ventilation. Ensure that the rack is not congested, because each device
generates heat. An enclosed rack should have louvered sides and a fan to provide cooling air. Heat
generated by equipment near the bottom of the rack can be drawn upward into the intake ports of the
equipment above it.
• When mounting a chassis in an open rack, ensure that the rack frame does not block the intake or exhaust
ports. If the chassis is installed on slides, check the position of the chassis when it is seated in the rack.
Power Guidelines and Requirements
Check the power at your site to ensure that you are receiving "clean" power (free of spikes and noise). Install
a power conditioner if necessary.
The AC power supply supports either 110V or 220V operation. All units include a 6-foot (1.8-meter) electrical
power cord. (A label near the power inlet indicates the correct voltage, frequency [AC-powered systems only],
current draw, and power dissipation for the unit.)
Preparing for Installation
4
Preparing for Installation
Mounting Requirements
Network Cabling Specification
• Ethernet cables for RJ45 ports
• Serial or console cables used to connect devices like routers
• Shielded USB cables with properly terminated shields for the USB port
• Standard Shielded Cable with 15-Pin VGA Male Connector
Required Tools and Equipment
You will need the following equipment to install the device and its equipment:
• ESD-preventive cord and wrist strap
• Phillips screwdrivers: small, 3/16-in. (4 to 5 mm), and medium, 1/4-in. (6 to 7 mm)
• Screws that fit your rack
• Wire crimper for chassis grounding - to be used along with the ground lug kit
• One AWG 6 cable for the ground lug kit
The ground lug is for chassis grounding and is NEBS compliant.
Note
In addition, depending on the type of modules you plan to use, you might need the following equipment to
connect a port to an external network
• Cables for connection to the WAN and LAN ports (dependent on the configuration)
If you order the required cables when you purchase the device, the cables ship
along with the product.
Note
Preparing for Installation
5
Preparing for Installation
Network Cabling Specification
Preparing for Installation
6
Preparing for Installation
Required Tools and Equipment
Inhaltsverzeichnis
Andere Cisco Netzwerk-Hardware Handbücher
Cisco
Cisco ASR 9000 Series Bedienungsanleitung
Cisco
Cisco Fourth-Generation Versatile Interface Processor... Bedienerhandbuch
Cisco
Cisco NCS 1001 Leitfaden
Cisco
Cisco NCS 1004 Bedienungsanleitung
Cisco
Cisco 2610 - Router - EN Bedienungsanleitung
Cisco
Cisco BR1400 Series Kurzanleitung
Cisco
Cisco Edge 300 Series Kurzanleitung
Cisco
Cisco Firepower 1010 FPR1010-NGFW-K9 Handbuch
Cisco
Cisco Firepower 4100 Series Bedienungsanleitung
Cisco
Cisco NCS 4016 Bedienungsanleitung
Cisco
Cisco PC4000 Bedienungsanleitung
Cisco
Cisco Cisco ASA Series Bedienungsanleitung
Cisco
Cisco Catalyst 8510 Bedienungsanleitung
Cisco
Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Bedienungsanleitung
Cisco
Cisco ONS 15600 Bedienungsanleitung
Cisco
Cisco AIR-WLC2106-K9 - Wireless LAN Controller... Bedienungsanleitung
Cisco
Cisco ASR 5000 Bedienungsanleitung
Cisco
Cisco ONS 15310-MA SDH Handbuch
Cisco
Cisco ATM Cable Interface Processor ACIP-SM(=) Bedienerhandbuch
Cisco
Cisco GS7000 Leitfaden
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
