Cisco Firepower 4100 Series Bedienungsanleitung

Overview

•Features, on page 1

•Deployment Options, on page 5

•Package Contents, on page 5

•Serial Number Location, on page 6

•Front Panel, on page 8

•Front Panel LEDs, on page 9

•Rear Panel, on page 10

•Network Modules, on page 11

•Hardware Bypass Network Modules, on page 15

•Power Supply Modules, on page 22

•Fan Modules, on page 24

•Supported SFP/SFP+ and QSFP Transceivers, on page 25

•Hardware Specifications, on page 28

•Product ID Numbers, on page 29

•Power Cord Specifications, on page 32

Features

The Cisco Firepower 4100 is a standalone modular security services platform. It is capable of running multiple

security services simultaneously and so is targeted at the data center as a multiservice platform. The series

includes the Firepower 4112, 4115, 4125, and 4145. See Product ID Numbers, on page 29 for a list of the

product IDs (PIDs) associated with the 4100 series.

The Firepower 4100 supports Cisco Secure Firewall Threat Defense, Cisco Secure Firewall eXtensible

Operating System (FXOS), and Cisco Secure Firewall ASA software. See Cisco Firepower 4100/9300 FXOS

Compatibility, which lists software and hardware compatibility information for the Firepower 4100 series.

The following figure shows the Firepower 4100.

Overview

Figure 1: Firepower 4100

The following table lists the features for the Firepower 4100.

Table 1: Firepower 4100 Features

4145412541154112Feature

•Common Criteria (CC) certification for the Network Device

Collaborative Protection Profile (NDcPPv2.2E), VPN

Gateway Module (VPNGW_MOD_v1.1), and Firewall

Module (FW_MOD_v1.4e) for ASA 9.16.x.

• Common Criteria (CC) and Commercial Solutions for

Classified (CSFC) for FTD 6.2.x.

•CC for the Network Device Collaborative Protection Profile

(NDcPPv2.1) for ASA 9.12.xand FX-OS 2.6.x.

• Federal Information Processing Standards (FIPS) 140-2 on

ASA 9.12.x, FTD 6.4.x, and FX-OS 2.6.x.

• Department of Defense Information Network Approved

Product List (DoDIN APL) for ASA 9.12.xand FTD 6.4.x.

• US Government Compliance for IPv6 (USGv6) for ASA

9.8.xand FTD 6.2.x.

Firepower 4112 has not yet completed the above

certifications.

Note

See the "Security Certifications Compliance" chapter

in the Cisco FXOS CLI Configuration Guide or Cisco

FXOS Firepower Chassis Manager Configuration

Guide for the procedure to enable security modes.

Note

—Security standards

certifications

—Certified

——Network Equipment

Building Systems

(NEBS) certification

1 RU

Fits a standard 19-inch (48.3cm) square-hole rack

Form factor

Overview

Features

4145412541154112Feature

Slide rails, mount ears, and screws included (4-post EIA-310-D rack)Rack mount

Front to rear

Cold aisle to hot aisle

Airflow

Two 22-core

2.1-GHz Intel Xeon

6152

Two 16-core

2.1-GHz Intel Xeon

6130T

Two 12-core

2.1-GHz Intel Xeon

4116

One 12-core

2.1-GHz Intel Xeon

4116

Processor

384-GB DRAM

12 x 32-GB

DDR4-2666

192-GB DRAM

12 x 16-GB

DDR4-2666

192-GB DRAM

12 x 16-GB

DDR4-2400

96-GB DRAM

6 x 16-GB

DDR4-2400

Memory

With two 8-port network modules installed

Maximum number

of interfaces

One Gigabit Ethernet

Supports 1-Gb fiber or copper SFPs

Management port

One RJ-45 consoleSerial port

One USB 2.0 Type AUSB port

Eight fixed 1-Gb and 10-Gb SFP+ ports (named Ethernet 1/1 through 1/8)Network ports

Eight fixed 1-Gb and 10-Gb SFP+ portsSmall form-factor

pluggable (SFP)

ports

Displays the serial number; on the front panelPullout asset card

On rear panelGrounding lug

On front panelLocator beacon

On rear panelPower switch

Two network module slots (network module 2 and network module 3)Network modules

Overview

Features

4145412541154112Feature

• 8-port 10-Gigabit Ethernet SFP+

• 4-port 40-Gigabit Ethernet QSFP+

• 8-port 1-Gigabit Ethernet copper with hardware bypass

• 2-port 40-Gigabit Ethernet QSFP+ (built-in) with hardware bypass

• 6-port 1-Gigabit Ethernet SX fiber SFP (built-in) with hardware bypass

• 6-port 10-Gigabit Ethernet SR fiber SFP+ (built-in) with hardware bypass

• 6-port 10-Gigabit Ethernet LR fiber SFP+ (built-in) with hardware bypass

• 2-port 100-Gigabit Ethernet QSFP28

First supported in threat defense 7.2 and ASA 9.18.1.

Note

Supported network

modules

Two (1+1) power supply module slots

Ships with two 1100-W AC power supply

modules

Hot-swappable

Two (1+1) power supply module slots

Ships with one 1100-W AC power supply

module

Hot-swappable

AC power supply

Two (1+1) power supply module slots

950-W DC power supply module

Hot-swappable

DC power supply

(optional)

1+1Redundant power

Six fan module slots

5+1 redundancy

Hot-swappable

Fan

Two SSD slots

Ships with one 800-GB SSD installed in

slot 1. Slot 1 is the primary SSD and

should always be present.

RAID is not supported.

Note

The SSD must be installed in

slot 1. Slot 2 is reserved only

for the optional MSP.

Caution

Two SSD slots

Ships with one 400-GB SSD installed in

slot 1. Slot 1 is the primary SSD and

should always be present.

RAID is not supported.

Note

The SSD must be installed in

slot 1. Slot 2 is reserved only

for the optional Malware

Storage Pack (MSP).

Caution

Storage

Installed in the second SSD slot onlyMSP (optional)

Overview

Features

Deployment Options

Here are some examples of how you can deploy the Firepower 4100:

• In a data center using NGFW and ASA

• At the core/aggregation layer of a 3-tier data center in a high availability configuration

• As a dedicated multifunctional security service within converged infrastructure stacks, for example,

vBlock, FlexPod, and so forth, at the access layer

• As a high-performance data center security appliance between the WAN edge and the data center core

in a high availability configuration

• Inter-DC clustering deployments

• In newer spine/leaf data center designs, deployment as a leaf that exclusively offers security functions

Package Contents

The following figure shows the package contents for the Firepower 4100. Note that the contents are subject

to change and your exact contents might contain additional or fewer items.

Figure 2: Firepower 4100 Package Contents

Blue console cable PC terminal adapter (part

number 72-3383-01)

2Firepower 4100 chassis1

Overview

Deployment Options

10/100/1000BASE-T SFP transceiver4Two power cords (country-specific)

See Power Cord Specifications, on page 32 for

a list of supported power cords.

Cable management bracket kit (part number

69-100376-01)

• Two cable management brackets (part

number 700-106377-01)

• Four 8-32 x 0.375-inch Phillips screws (part

number 48-2696-01)

6Ground lug kit (part number 69-1000359-01):

• One ground lug #6 AWG, 90 degree, #10

post (part number 32-0608-01)

•Two 10-32 x 39-8-inch Phillips Head screws

(part number 48-0700-01)

Two slide rail locking brackets (part number

700-105350-02)

Six 8-32 x 0.375-inch Phillips screws (part

number 48-2696-01)

8Two slide rails with two M3 x 0.5 x 6-mm screws

(48-101144-01)

Flextronics tie wrap and tie wrap clamp (part

number 52-100202-01)

10Artesyn tie wrap and tie wrap clamp (part number

52-100204-01)

—Cisco Secure Firepower 4100

This document has a URL and QR code that point

to the Digital Documentation Portal. The portal

contains links to the Product Information page,

the Hardware Installation Guide, the Regulatory

and Safety Information Guide, the Getting Started

Guide, and the Easy Deployment Guide.

Serial Number Location

The serial number for the Firepower 4100 series chassis is located on the pullout asset card on the front panel.

Overview

Serial Number Location

Figure 3: Serial Number on the 4100 Chassis

You can also view additional model information on the compliance label located on the bottom of the chassis.

Figure 4: Compliance Label on the 4100 Chassis

Overview

Serial Number Location

Front Panel

The following figure shows the front panel of the Firepower 4100.

Figure 5: Firepower 4100 Front Panel

Gigabit Ethernet management port2RJ-45 console port1

Eight fixed SFP+ (1-Gb/10-Gb) ports (in network

module slot 1)

Ethernet 1/1 through 1/8 labeled top to bottom,

left to right

4USB 2.0 Type A port3

SSD 2

Reserved for the optional MSP.

6SSD 1

Reserved for the primary SSD; slot 1 must always

be populated.

Locator LED8Power LED7

Network module 2

The 10-Gb network module is shown.

Note

10Pullout asset card9

Network module 3

The 10-Gb network module is shown.

Note

RJ-45 Console Port

The Firepower 4100 has a standard RJ-45 console port. You can use the CLI to configure your Firepower

4100 through the RJ-45 serial console port by using a terminal server or a terminal emulation program

on a computer.

The RJ-45 (8P8C) port supports RS-232 signaling to an internal UART controller. The console port does

not have any hardware flow control, and does not support a remote dial-in modem. The baud rate is 9600.

You can use the standard cable found in your accessory kit to convert the RJ-45 to DB-9 if necessary.

Type A USB Port

You can use the external USB Type A port to attach a data storage device. The external USB drive

identifier is disk1:. The USB Type A port supports the following:

• Hot swapping

Overview

Front Panel

• USB drive formatted with FAT32

• Boot kick-start image from the Supervisor ROMMON for discovery recovery purposes

• Copy files to and from workspace:/ and volatile:/ within local-mgmt. The most relevant files are:

• Core files

• Ethanalyzer packet captures

• Tech-support files

• Security module log files

• Platform bundle image upload using download image usbA:

The USB Type A port does not support Cisco Secure Package (CSP) image upload.

Network Ports

The Firepower 4100 chassis has eight fixed ports that require 1-Gb/10-Gb SFP/SFP+ transceivers (fiber

or copper). They are numbered from left to right starting with 1 and are named Ethernet 1/1 through

Ethernet 1/8. The 4100 also has two network module slots that support different numbers of ports

depending on the network module. See Network Modules, on page 11 for the supported network modules.

See for Supported SFP/SFP+ and QSFP Transceivers, on page 25 the list of supported transceivers.

Each port has LEDs that represent link/activity status.

Management Port

The Firepower 4100 chassis has a management port that requires a 1-Gb fiber or copper SFP.

Front Panel LEDs

The following figure and table describe the Firepower 4100 front panel LEDs.

Figure 6: Front Panel LEDs

Overview

Front Panel LEDs

Health (SYS)

• Off—System is not booting yet.

• Green, flashing—Power-up diagnostics are

complete and system is booting up.

• Green—The system has passed power-up

diagnostics.

• Amber—Power-up diagnostics has failed.

• Amber, flashing—Alarm; power-up

diagnostics are running.

2Management

• Off—No connection or port is not in use.

• Amber—No link or network failure.

• Green—Link up.

• Green, flashing—Network activity.

Power

• Off—Input power not detected.

• Green, flashing—Appears only when you

move the power switch from ON to OFF.

System is shutting down and powers off once

shutdown is completed.

• Amber—System is powering up.

• Green—System fully powered up.

• Amber, flashing—Reserved.

4SSD

• Off— SSD not present.

• Green—SSD is present; no activity.

• Green, flashing—SSD is active.

• Amber—SSD failure.

• Amber, flashing—Rebuilding, flashes at 1

Hz.

•Amber, flashing—Predictive failure analysis

(PFA) and hot spare; two fast flashes at 4

Hz, pause for 0.5 seconds.

Locator LED

• Off—Locate is off.

• Blue—Locate is on.

6Active (ACT)

This LED is not supported; reserved for future

use.

Network activity

• Off—No connection or port is not in use.

• Amber—No link or network failure.

• Green—Link up.

• Green, flashing—Network activity.

Rear Panel

The following figure shows the rear panel of the Firepower 4100.

Overview

Rear Panel

Andere Handbücher für Firepower 4100 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Netzwerk-Hardware Handbücher

Cisco

Cisco ISA500 Series Bedienungsanleitung

Cisco

Cisco Nexus 3000 series Bedienungsanleitung

Cisco

Cisco Network Adapter VIP-FE-TX/4E Bedienerhandbuch

Cisco

Cisco ONS 15454 SDH Handbuch

Cisco

Cisco IDS-4230-FE - Intrusion Detection Sys Fast Ethernet... Bedienerhandbuch

Cisco

Cisco MXE 3000 Handbuch

Cisco

Cisco Firepower 1010 FPR1010-NGFW-K9 Handbuch

Cisco

Cisco SCE8000 GBE Bedienerhandbuch

Cisco

Cisco LightStream 1010 Handbuch

Cisco

Cisco ONS 15454 M12 Bedienungsanleitung

Cisco

Cisco IAD1101 Bedienungsanleitung

Cisco

Cisco Aironet 1040 Series Bedienungsanleitung

Cisco

Cisco Firepower 2130 Wartungs- und Serviceanleitung

Cisco

Cisco 2600 Series Technisches Dokument

Cisco

Cisco Firepower 1010 Bedienungsanleitung

Cisco

Cisco GS7000 Bedienungsanleitung

Cisco

Cisco OL-7822-06 Bedienungsanleitung

Cisco

Cisco Nexus 93180LC-EX Bedienungsanleitung

Cisco

Cisco ASR 5500 Bedienungsanleitung

Cisco

Cisco 3660 Series Bedienungsanleitung

Cisco

Cisco CMX 3375 Bedienungsanleitung

Cisco

Cisco GS7000 Betriebsanleitung

Cisco

Cisco Engine 611 Bedienungsanleitung

Cisco

Cisco Secure Firewall Management Center 1700 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung