Cisco MA-UMNT-MR-A3 Bedienungsanleitung

MA-UMNT-MR-A3 Aruba Mounting Adapter Installation Guide

Overview

The MA-UMNT-MR-A3 is a universal mounting adapter designed to simplify the transition from Aruba to Cisco Meraki access points. This adapter works with

MR33, MR42/42E, MR52, MR53/53E, MR45/55, MR36/46/46E/56 indoor access points. MA-UMNT-MR-A3 can be attached directly to the Aruba mount without

the need to remove this mount from its current mounting location. Supported Aruba mounts: JW046A, JW047A, AP-200-MNT-W2, AP-220-MNT-W2,

AP-220-MNT-W2W.

Package Contents

MA-UMNT-MR-A3 standard package includes the following equipment:

•1x MA-UMNT-MR-A3

•1x PH#2 M4XP0.6X14L security screw

•2x PH 19mm long screws, M3.5 threads

•1x TORX M4XP0.6X14L security screw

Note: The MA-UMNT-MR-A3 does not work with any of the outdoor MR access points.

Note: The MA-UMNT-MR-A3 cannot mount Meraki access points by itself and must be paired with one of the listed Aruba mounts.

Collect Tools

You will need the following tools to perform an installation:

1x Phillips head screwdriver

1x TORX screwdriver

Installation Instructions

Remove the current Aruba access point from the Aruba mount and ensure that the security lock on MA-UMNT-MR-A3 is not engaged.

1. If JW046A / JW047A Aruba mounts are used, position the MA-UMNT-MR-A3 to align with the currently installed Aruba mount, placing the MA-UMNT-

MR-A3 so that it’s mounting tabs are at an angle of approximately 30 degrees to the Aruba mount. Pushing toward the wall, rotate the MA-UMNT-MR-A3

clockwise until it clicks into place.

If AP-200-MNT-W2 / AP-220-MNT-W2 / AP-220-MNT-W2W Aruba mounts are used, align the pins on the rear panel of the MA-UMNT-MR-A3 with the slots on

the Aruba mount plate. Press the button on the bottom on the Aruba mount in and slide the MA-UMNT-MR-A3 into the Aruba mount until the pins are fully

engaged. Release the button to secure the MA-UMNT-MR-A3 to the Aruba mount. For additional security, insert the Torx security screw into the hole located

next to the button to lock the MA-UMNT-MR-A3 to the Aruba mount.

2. Use a Phillips head screwdriver to secure MA-UMNT-MR-A3 and ensure it’s in a locked position.

3. Use the two Phillips head screws included in the mount kit to attach your Meraki mount cradle to the MA-UMNT-MR-A3 mount.

Attach your Meraki access point to the Meraki mount cradle by lining up the top edge of the AP with the top tab of the mount cradle. Since the cradle is already

mounted to MA-UMNT-MR-A3 universal mount, guide the AP towards the top tab and insert the top tab into the AP slot.

Then adjust your AP to guide the bottom slot into the cradle’s bottom tab until it clicks into place.

Once in place, the AP should be secured to the cradle by using one of the included screws in the cradle’s bottom tab.

4. Run Ethernet cable(s) to LAN Access ports of your Meraki access point and connect into the appropriate LAN Access port(s). Note some Meraki APs

have 1x LAN port and some have 2x LAN ports. Secure the AP with a Torx security screw.

Inhaltsverzeichnis

Andere Cisco Netzwerk-Hardware Handbücher

Cisco

Cisco Catalyst 8510 Bedienungsanleitung

Cisco

Cisco NCS 1004 Bedienungsanleitung

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet Bedienungsanleitung

Cisco

Cisco Meraki MX68 Handbuch

Cisco

Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control... Bedienungsanleitung

Cisco

Cisco ONS 15454 Bedienungsanleitung

Cisco

Cisco WEC600N Bedienungsanleitung

Cisco

Cisco Nexus 93180LC-EX Bedienungsanleitung

Cisco

Cisco SA-VAM - VPN Acceleration Module Bedienerhandbuch

Cisco

Cisco CTM GateWay Installationsanleitung

Cisco

Cisco NTP-E157 Stücklistenhandbuch

Cisco

Cisco ASA Kurzanleitung

Cisco

Cisco NCS 4206 Bedienungsanleitung

Cisco

Cisco ASR 5000 Bedienungsanleitung

Cisco

Cisco 7606 Bedienungsanleitung

Cisco

Cisco ON100 Network Agent Bedienungsanleitung

Cisco

Cisco ONS 15454 DWDM Bedienungsanleitung

Cisco

Cisco Network Storage System NSS3000 Series Bedienungsanleitung

Cisco

Cisco GS7000 Betriebsanleitung

Cisco

Cisco NCS 1001 Leitfaden

Cisco

Cisco Wide Area Application Engine 612 Handbuch

Cisco

Cisco Aironet 340 Series Bedienungsanleitung

Cisco

Cisco NSS2000 - Gigabit Storage System Chassis Anleitung zur Verwendung

Cisco

Cisco Aironet 340 Series Anleitung zur Verwendung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung