Cisco FirePOWER 8000 Series Bedienungsanleitung

Insert and Remove a Network Module (NetMod) on

an 8000 Series FirePOWER Appliance

Document ID: 118194

Contributed by Nazmul Rajib and Josiah Zimmermann, Cisco TAC

Engineers.

Aug 06, 2014

Contents

Introduction

Prerequisites

Before You Begin

Required Tool and Hardware

Remove the Module or Slot Cover

Insert a Module or Slot Cover

Introduction

Instead of the usual fixed port configuration of most high−end security appliances, the modularity of the 8000

Series appliances enables you to choose and change the number and type of interfaces for the appliance.

Various Network Modules (NetMods) are inserted into the 8000 Series appliances to customize the interface

configuration to match your network requirements. This document describes how to insert and remove a

NetMod in an 8000 series FirePOWER appliance.

Caution: If you install a NetMod in an incompatible slot on your appliance or a NetMod is otherwise

incompatible with your system, an error or warning message appears in the web interface on the managing

Defense Center when you attempt to configure the NetMod.

Prerequisites

Before You Begin

Before you begin, prepare to insert or remove your module using the following guidelines:

Identify all appliance and module parts.• Identify the slots where you want to install your NetMods.• Identify the correct slots for your stacking modules.• Confirm that the EMI gaskets are in place.• Unplug all power cords from the appliance.•

Warning: You cannot hot−swap modules. You must power down and unplug both power cords from the

appliance before inserting or removing modules.

Caution: Use proper electrostatic discharge (ESD) practices such as wearing wrist straps and using an ESD

work surface when handling the modules. Store unused modules in an ESD bag or box to prevent damage.

Required Tool and Hardware

T8 Torx screwdriver• 8000 Series FirePOWER appliance•

Remove the Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to release the latch.

Step 3: Slide the module out of the slot.

Insert a Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to open the latch. The near end of the latch is visible. The far

end of the latch is inside the module.

Step 3: Insert the module into the slot until the far end of the latch is inside the slot and the near end of the

latch touches the outside of the slot.

Step 4: Push the lever toward the module so that the latch engages and pulls the module into the slot.

Step 5: Press firmly on the screw hole to push the lever fully against the module to secure the latch.

Step 6: Insert and tighten the reserved T8 Torx screw into the lever.

Updated: Aug 06, 2014 Document ID: 118194

Inhaltsverzeichnis

Andere Cisco Netzwerk-Hardware Handbücher

Cisco

Cisco NSS4100 - Gigabit Storage System Bedienungsanleitung

Cisco

Cisco ASR 5000 Bedienungsanleitung

Cisco

Cisco NCS 2002 Bedienungsanleitung

Cisco

Cisco DOC 785983 Bedienungsanleitung

Cisco

Cisco SCE 1000 and Bedienerhandbuch

Cisco

Cisco ONS 15454 DWDM Bedienungsanleitung

Cisco

Cisco IAD2430 Series Installationsanleitung

Cisco

Cisco IPS 7.1 Bedienungsanleitung

Cisco

Cisco ONS 15454 Bedienungsanleitung

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Bedienerhandbuch

Cisco

Cisco MERAKI MX85 Series Handbuch

Cisco

Cisco RSP7000 Bedienungsanleitung

Cisco

Cisco Firepower 1010 Series Handbuch

Cisco

Cisco WAVE-574-K9 - Wide Area Virtualization Engine... Handbuch

Cisco

Cisco Linksys WES610N Bedienungsanleitung

Cisco

Cisco IPS-4240-K9 - Intrusion Protection Sys 4240 Bedienungsanleitung

Cisco

Cisco 8540 - Catalyst Campus Switch Router Modular Expansion... Bedienungsanleitung

Cisco

Cisco GS7000 Betriebsanleitung

Cisco

Cisco NCS 2000 series Bedienungsanleitung

Cisco

Cisco Mc3810 - 16MB Flash Memory Kurzanleitung

Cisco

Cisco NCS 1002 Firmware-Update

Cisco

Cisco ONS 15200 Series Bedienungsanleitung

Cisco

Cisco LightStream 1010 Handbuch

Cisco

Cisco Remote PHY Shelf 7200 Installationshandbuch

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung