Cisco NCS 4206 Bedienungsanleitung

Installing the Cisco NCS 4206

This chapter describes how to install the Cisco NCS 4206 and includes the following sections:

•Prerequisites, on page 1

•Installing the Chassis in a Rack, on page 1

•Installing the Chassis Ground Connection, on page 10

•Installing the Fan Tray, on page 12

•RSP Installation, on page 16

•Interface Module Installation, on page 20

•Installing the Power Supply, on page 22

•Installing the AC power Supply, on page 28

•Power Cable Bracket (A9XX-PWR-CBL-MGMT), on page 31

•Top Cable Management Bracket (A9XX-TOP-CBL-MGMT), on page 33

•Connecting the Cisco NCS 4206 to the Network, on page 35

Prerequisites

Before installing the Cisco NCS 4206, it is important to prepare for the installation by:

• Preparing the site (site planning) and reviewing the installation plans or method of procedures (MOP)

• Unpacking and inspecting the Cisco NCS 4206

• Gathering the tools and test equipment required to properly install the Cisco NCS 4206

For more instructions on how to prepare for the installation of the Cisco NCS 4206, see Preparing for

Installation.

Installing the Chassis in a Rack

The following sections describe how to install the Cisco NCS 4206 in a rack.

Installing the Chassis Brackets

The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis. To

install the brackets on the front of the chassis, perform these steps:

Installing the Cisco NCS 4206

Step 1 Remove the rack-mount brackets from the accessory kit and position them beside the chassis.

Figure 1: Attaching Mounting Brackets for a 19-inch Rack (A903-RCKMNT-19IN3)

Figure 2: Attaching Mounting Brackets for a 23-inch EIA Rack

Step 2 Position one of the brackets against the chassis side, and align the screw holes.

Step 3 Secure the bracket to the chassis with the screws removed when performing Step 1. The recommended maximum torque

is 28 in.-lb (3.16 N-m).

Step 4 Repeat Step 2 and Step 3 for the other bracket.

Installing the Cisco NCS 4206

Installing the Chassis Brackets

Installing the Chassis in the Rack

The procedures in this section apply to both horizontal and vertical mounting of the in a rack.

To install the chassis in the equipment rack, perform these steps:

Step 1 Position the chassis in the rack as follows:

• If the front of the chassis (front panel) is at the front of the rack, insert the rear of the chassis between the mounting

posts.

• If the rear of the chassis is at the front of the rack, insert the front of the chassis between the mounting posts.

Step 2 Guide the chassis carefully into the plenum assembly. See the figure below.

Figure 3: Installing the Chassis on a 19-inch Rack (A903-RCKMNT-19IN3)

Installing the Cisco NCS 4206

Installing the Chassis in the Rack

Figure 4: Installing the Chassis on the Plenum in Rack

Securing screws to chassis onto rack3Plenum1

—Cable guides on chassis2

Step 3 Position the door onto the chassis and slide it into the rack. Secure the screws with a torque of n.-lb (N-m). See the figure

below.

Figure 5: Installing Door onto Chassis in Rack

Installing the Cisco NCS 4206

Installing the Chassis in the Rack

Securing door to the chassis onto rack3Chassis in plenum1

—Door2

Step 4 Align the mounting holes in the bracket (and optional cable guide) with the mounting holes in the equipment rack.

Do not use interface module and power supply ejector handles to lift the chassis; using the handles to lift the

chassis can deform or damage the handles.

Caution

Figure 6: Installing the Chassis in a 23-inch EIA Rack

Step 5 Install the 8 or 12 (4 or 6 per side) 12-24 x 3/4-inch or 10-32 x 3/4-inch screws through the holes in the bracket and into

the threaded holes in the equipment rack posts.

Step 6 Use a tape measure and level to verify that the chassis is installed straight and level.

Installing the Chassis with Plenum in Rack

Step 1 Position the air baffle and the side plate to the plenum. See figure below.

Installing the Cisco NCS 4206

Installing the Chassis with Plenum in Rack

Figure 7: Securing the Air Baffle Tray

Plenum base3Air baffle1

Secure screw to Plenum base4Side plate2

Step 2 Secure the air baffle and the side plate using a maximum torque of 11.5 in.-lb (1.3 N-m). See figure below.

Installing the Cisco NCS 4206

Installing the Chassis with Plenum in Rack

Figure 8: Securing the Side Plate

——Securing side plate to plenum base1

Step 3 Repeat Step-1 and Step-2 to complete the plenum assembly on the other side of the plenum base.

Step 4 Position the air filter (A903-F2B-AIR-F) assembly on the plenum deflector. Secure the front cover using a recommended

torque of 11.5 in.-lb (1.3 N-m). See figure below.

Installing the Cisco NCS 4206

Installing the Chassis with Plenum in Rack

Figure 9: Air Filter

The filter is applicable when fan A903-FAN-H is used.

Note

Step 5 Using a crimping tool (as specified by the ground lug manufacturer), crimp the ground lug to the ground wire and connect

the other end of the ground wire to a suitable grounding point at your site. See figure below.

Installing the Cisco NCS 4206

Installing the Chassis with Plenum in Rack

Figure 10: Attaching the Ground Lug and Wire Assembly

Dual ground screws2Dual-hole ground adapter and dual-hole lug1

Step 6 Position the plenum assembly to the rack and secure the cable brackets to the rack using a torque of 11.5 in.-lb (1.3 N-m).

See figure below.

Installing the Chassis in the Air Plenum

Ensure that the chassis is not installed in the air plenum while mounting it on the rack.

Note

For instructions on mounting the plenum on the rack:

Step 1 Position the chassis so that the rear of the chassis is at the front of the plenum.

Step 2 Slide the chassis into the plenum so that the front of the chassis is in flush with the mounting rails and brackets. See the

figure below.

Installing the Cisco NCS 4206

Installing the Chassis in the Air Plenum

Figure 11: Cisco NCS 4206 Chassis with Plenum

Installing the Chassis Ground Connection

Before you connect the power or turn on the power to the Cisco NCS 4206, you must provide an adequate

chassis ground (earth) connection to your chassis.

This section describes how to ground the Cisco NCS 4206 chassis on a rack. The chassis provides two locations

for attaching a 2-hole grounding lug according to the rack-mounting brackets you use to install the chassis.

The Cisco NCS 4206 supports the following rack-mounting types:

• EIA 23-inch rack—Attach the grounding lug to the rack, as shown in the figure below

Installing the Cisco NCS 4206

Installing the Chassis Ground Connection

Inhaltsverzeichnis

Andere Cisco Netzwerk-Hardware Handbücher

Cisco

Cisco OL-6109-01 Bedienungsanleitung

Cisco

Cisco CiscoWorks Wireless LAN Solution Engine Bedienerhandbuch

Cisco

Cisco 7606 Bedienungsanleitung

Cisco

Cisco ASR 901S Series Betriebsanleitung

Cisco

Cisco 2650XM Bedienungsanleitung

Cisco

Cisco Content Engine 510 Bedienungsanleitung

Cisco

Cisco Firepower 9300 Wartungs- und Serviceanleitung

Cisco

Cisco ONS 15310-CL Bedienungsanleitung

Cisco

Cisco OL-7822-06 Bedienungsanleitung

Cisco

Cisco RSP4+ Bootflash Memory Upgrade to 16MB... Bedienerhandbuch

Cisco

Cisco CPS-MSP-1RU-K9 Bedienungsanleitung

Cisco

Cisco ONS 15327 Bedienerhandbuch

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... Bedienungsanleitung

Cisco

Cisco VSVM Bedienungsanleitung

Cisco

Cisco NCS 1004 Bedienungsanleitung

Cisco

Cisco NCS 1001 Handbuch

Cisco

Cisco Catalyst 8510 Bedienungsanleitung

Cisco

Cisco ONS 15454 SDH E1-75 Bedienungsanleitung

Cisco

Cisco CX-FEIP-1FX= Installation and con?guration Bedienungsanleitung

Cisco

Cisco NCS 4201 Handbuch

Cisco

Cisco C7200-I - Input/Output Controller - Control... Bedienungsanleitung

Cisco

Cisco SPA901-UK - Small Business Pro Bedienungsanleitung

Cisco

Cisco GS7000 Betriebsanleitung

Cisco

Cisco CTM GateWay Installationsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung