Cisco NCS 1004 Bedienungsanleitung
Safety Guidelines
Before you perform any procedure in this publication, you must review the safety guidelines in this section
to avoid injuring yourself or damaging the equipment. Note that this section contains guidelines, and does
not include every potentially hazardous situation. During any installation procedure, always use caution and
common sense.
Review the complete list of safety warnings available at Regulatory Compliance and Safety Information for
Cisco NCS 1004 Series.
•Standard Warning Statements, on page 1
•General Safety Guidelines for Personal Safety and Equipment Protection, on page 2
•Safety Precaution for Module Installation and Removal, on page 2
•Safety with Electricity, on page 3
•Power Connection Guidelines , on page 3
•Safety Precaution for Energy Hazard, on page 4
•Safety Precaution for Laser Radiation, on page 4
•Prevent Electrostatic Discharge Damage , on page 5
•NEBS Regulatory Compliance Statements, on page 6
Standard Warning Statements
This unit is intended for installation in restricted access areas. A restricted access area can be accessed
only by using a special tool, lock and key, or other means of security.Statement 1017
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Hazardous voltage or energy may be present on power terminals. Always replace cover when terminals
are not in service. Be sure uninsulated conductors are not accessible when cover is in place. Statement
1086
Warning
Safety Guidelines
1
Mount the device on a rack that is permanently affixed to the building.Statement 1049
Warning
Ultimatedisposalofthisproductmustbehandledaccordingtoallnationallawsandregulations.Statement
1040
Warning
General Safety Guidelines for Personal Safety and Equipment
Protection
Follow these safety guidelines:
• Never attempt to lift an object that might be too heavy for you to lift by yourself.
• Always unplug power cables when performing maintenance or working on the chassis, unless the
replacement part is hot swappable and designed for online insertion and removal (OIR).
• Keep the work area clear and dust free during and after installation.
• Keep tools and chassis components away from walkways and equipment rack aisles.
• Do not wear loose clothing, jewelry (including rings and chains), or other items that could get caught in
the equipment.
• Fasten your tie or scarf and sleeves.
• Operate Cisco equipment safely by using it in accordance with its electrical ratings and product usage
instructions.
• Do not work alone if potentially hazardous conditions exist.
• Ensure that the installation of the router is in compliance with national and local electrical codes: in the
United States, National Fire Protection Association (NFPA) 70, United States National Electrical Code;
in Canada, Canadian Electrical Code, part I, CSA C22.1; in other countries, International Electrotechnical
Commission (IEC) 364, part 1 through part 7.
Safety Precaution for Module Installation and Removal
Ensure to observe the following safety precautions when you are working with the chassis modules.
Invisible laser radiations present.Statement 1016
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams
or view directly with optical instruments.Statement 1051
Warning
Safety Guidelines
2
Safety Guidelines
General Safety Guidelines for Personal Safety and Equipment Protection
Safety with Electricity
Before working on a chassis or with power supplies, unplug the power cord on AC units. Disconnect
the power at the circuit breaker on DC units.Statement 12
Warning
Beforeworkingonequipmentthatisconnectedtopowerlines,removejewelry(including rings, necklaces,
and watches). Metal objects heat up when connected to power and ground and can cause serious burns
or weld the metal object to the terminals.Statement 43
Warning
Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There
may be a risk of electric shock from lightning. Statement 1088
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority
or an electrician if you are uncertain that suitable grounding is available.Statement 1024
Warning
This unit may have more than one power supply connection. All connections must be removed to
de-energize the unit.Statement 1028
Warning
Wheninstalling or replacingthe unit,ensurethe ground connection firstand disconnected last. Statement
1046
Warning
Thisequipment is intended to be groundedtocomply with emission and immunity requirements.Ensure
that the switch functional ground lug is connected to earth ground during normal use. Statement 1064
Warning
Power Connection Guidelines
Check the power at your site to ensure you are receiving clean power (free of spikes and noise).
Ensure to observe the following safety guidelines while connecting the device power supplies.
Safety Guidelines
3
Safety Guidelines
Safety with Electricity
Never defeat the ground conductor or operate the equipment in the absence of a suitably installed
ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are
uncertain that suitable grounding is available. Statement 1024
Warning
Use copper conductors only. Statement 1025
Warning
This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations. Statement 1045
Warning
Safety Precaution for Energy Hazard
Do not reach into a vacant slot when installing or removing a module. Exposed circuitry is an energy
hazard.Statement 206
Warning
The Cisco NCS 1004 can be configured for a DC power source. Do not touch terminals with body parts or
conductive objects while they are energized.
Safety Precaution for Laser Radiation
Cisco NCS 1004 is classified as Hazard Level 1M as per IEC 60825-2 and Laser Class 1/1M as per IEC
60825-1, since it may include Class 1 or Class 1M Laser sources.
Figure 1: Class 1M Laser Product Label
Safety Guidelines
4
Safety Guidelines
Safety Precaution for Energy Hazard
Figure 2: Class 1M Laser Product Label
Statement 291
Warning
Invisible laser radiations present.Statement 1016
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams
or view directly with optical instruments.Statement 1051
Warning
Prevent Electrostatic Discharge Damage
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD may occur when
electronic printed circuit cards are improperly handled and can cause complete or intermittent failures. When
removing and replacing modules, always follow these ESD prevention procedures:
• Ensure that the device chassis is electrically connected to earth ground.
• Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.
• Handle components by only their handles or edges; do not touch the printed circuit boards or connectors.
• Avoid contact between the printed circuit boards and clothing. The wrist strap only protects components
from ESD voltages on the body; ESD voltages on clothing can still cause damage.
Safety Guidelines
5
Safety Guidelines
Prevent Electrostatic Discharge Damage
NEBS Regulatory Compliance Statements
The NEBS-GR-1089-CORE regulatory compliance statements and requirements are discussed in this section.
The intra-building port(s) (Management Ethernet Ports) of the equipment or subassembly must use
shielded intra-building cabling/wiring that is grounded at both ends. Statement 7003
Warning
The intra-building port(s) (Management Ethernet Ports) of the equipment or subassembly is suitable
for connection to intra-building or unexposed wiring or cabling only. The intra-building port(s) of the
equipment or subassembly must not be metallically connected to interfaces that connect to the OSP or
its wiring for more than 6 meters (approximately 20 feet). These interfaces are designed for use as
intra-building interfaces only (Type 2, 4, or 4a ports as described in GR-1089) and require isolation
from the exposed OSP cabling. The addition of Primary Protectors is not sufficient protection in order
to connect these interfaces metallically to an OSP wiring system. Statement 7005
Warning
Productsthat haveACpowerports that areintendedfordeployments wherean externalSurgeProtective
Device (SPD) is utilized at the AC power service equipment (see definition in National Electric Code).
Statement 7012
This product is designed for a Common Bonding Network (CBN) installation. Statement 7013
This product can be installed in network telecommunication facilities or locations where the National
Electric Code applies. Statement 8015 and 8016
The DC return connection to this system should remain isolated from the system frame and chassis
(DC-I). Statement 7016
Safety Guidelines
6
Safety Guidelines
NEBS Regulatory Compliance Statements
Andere Handbücher für NCS 1004
5
Inhaltsverzeichnis
Andere Cisco Netzwerk-Hardware Handbücher
Cisco
Cisco 2600 Series Technisches Dokument
Cisco
Cisco NCS 2000 series Bedienungsanleitung
Cisco
Cisco NCS 1002 Bedienungsanleitung
Cisco
Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Bedienungsanleitung
Cisco
Cisco ATA 191 Bedienungsanleitung
Cisco
Cisco NCS 6008 LCC Bedienungsanleitung
Cisco
Cisco RSP7000 Bedienungsanleitung
Cisco
Cisco LightStream 1010 Bedienungsanleitung
Cisco
Cisco NCS 4016 Bedienungsanleitung
Cisco
Cisco Network Storage System NSS3000 Series Bedienungsanleitung
Cisco
Cisco NCS 1010 Merkblatt
Cisco
Cisco IPS-4260-K9 - IPS Sensor 4260 Bedienungsanleitung
Cisco
Cisco C8510MSR-SKIT-DC - Catalyst 8510 Multiservice Switch... Bedienungsanleitung
Cisco
Cisco IAD2430 Series Installationsanleitung
Cisco
Cisco 5400 Bedienungsanleitung
Cisco
Cisco IronPort C670 Bedienungsanleitung
Cisco
Cisco NAC3350-PROF-K9 - NAC Profiler Server Bedienungsanleitung
Cisco
Cisco Cisco ONS 15600 SDH Bedienungsanleitung
Cisco
Cisco Firepower 2100 Series Bedienungsanleitung
Cisco
Cisco Aironet 1400 Series Bedienungsanleitung
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
