Cisco Firepower 2100 Series Bedienungsanleitung

Rack-Mount and Ground the Chassis

•Unpack and Inspect the Chassis, on page 1

•Rack-Mount the Chassis Using Brackets, on page 2

•Rack-Mount the Chassis Using Slide Rails, on page 4

•Ground the Chassis, on page 9

Unpack and Inspect the Chassis

Keep the shipping container in case the chassis requires shipping in the future.

Tip

The chassis is thoroughly inspected before shipment. If any damage occurred during transportation or any

items are missing, contact your customer service representative immediately.

Note

See Package Contents for a list of what shipped with the chassis.

Step 1 Remove the chassis from its cardboard container and save all packaging material.

Step 2 Compare the shipment to the equipment list provided by your customer service representative. Verify that you have all

items.

Step 3 Check for damage and report any discrepancies or damage to your customer service representative. Have the following

information ready:

• Invoice number of shipper (see the packing slip)

• Model and serial number of the damaged unit

• Description of damage

• Effect of damage on the installation

Rack-Mount and Ground the Chassis

Rack-Mount the Chassis Using Brackets

This procedure describes how to install the Firepower 2100 in a rack using the rack-mount brackets. It also

describes how to install the optional cable management brackets. See Product ID Numbers for a list of the

PIDs associated with rack-mounting the chassis.

The rack is a standard Electronic Industries Association (EIA) rack. It is a 4-post-EIA-310-D, which is the

current revision as specified by EIA. The vertical hole spacing alternates at .50 inches (12.70 mm) to .625

inches (15.90 mm) to .625 inches (15.90 mm) and repeats. The start and stop space is in the middle of the

.50-inch holes. The horizontal spacing is 18.312 inches (465.1 mm), and the rack opening is specified as a

minimum of 17.75 inches (450 mm).

You need the following to install the Firepower 2100 in a rack:

• Phillips screwdriver

• Two rack-mount brackets (part number 700-106374-01) with six 8-32 x 0.281-inch screws (part number

48-101518-01)

The rack-mount brackets ship with the Firepower 2110/2120 and are orderable

for the Firepower 2130/2140.

Note

• Rack-mount screws:

The rack-mount screws ship with the Firepower 2110/2120 and are orderable for

the Firepower 2130/2140.

Note

• Four 12-24 x 0.75-inch Phillips screws (part number 648-0440-01) for securing the chassis to your

rack

• Four 10-32 x 0.75-inch Phillips screws (part number 48-0441-01) for securing the chassis to your

rack

• Four M6 x 1 x19-mm Phillips screws (part number 48-101022-01) for securing the chassis to your

rack

• (Optional) Cable management bracket kit (part number 69-100376-01):

• Two cable management brackets (part number 700-106377-01)

• Four 8-32 x 0.375-inch Phillips screws (part number 48-2696-01)

Step 1 Attach a rack-mount bracket to each side of the chassis using the six 8-32 x 0.281-inch Phillips screws (three per side).

Rack-Mount and Ground the Chassis

Rack-Mount the Chassis Using Brackets

Figure 1: Attach the Rack-Mount Bracket to the Side of the Chassis

Rack-mount bracket2Chassis1

8-32 x 0.281-inch Phillips screws (three per side)3

Step 2 (Optional) Attach the cable management bracket to the rack-mount bracket:

a) Install the cable management screws into the rack-mount bracket.

Figure 2: Install the Cable Management Screws into the Rack-Mount Bracket

b) Install two 8-32 x 0.375-inch screws through the inside of each rack-mount bracket to secure the cable management

bracket to the rack-mount bracket.

Rack-Mount and Ground the Chassis

Rack-Mount the Chassis Using Brackets

Step 3 Attach the chassis with the installed rack-mount bracket to the rack using the screws that work for your rack.

What to do next

• See Ground the Chassis, on page 9 for the procedure to ground the Firepower 2100.

• Install the cables according to your default software configuration as described in the Cisco Firepower

Getting 2100 Started Guide.

Rack-Mount the Chassis Using Slide Rails

This procedure describes how to install the Firepower 2100 series in a rack using slide rails. It applies to all

models of the 2100 series. It ships with the Firepower 2130 and 2140 chassis; it is optional for the 2110 and

2120. For the 2110 and 2120, you install three screws on the chassis to secure the slide rail. For the 2130 and

2140, you use the pegs on the chassis to secure the slide rail. See Product ID Numbers for a list of the PIDs

associated with racking the chassis.

You can install the optional cable management bracket on all models of the 2100 series. The optional cable

management bracket kit comes with two cable management brackets and four 8-32x0.375"L screws.

The rack is a standard Electronic Industries Association (EIA) rack. It is a 4-post-EIA-310-D, which is the

current revision as specified by EIA. The vertical hole spacing alternates at .50 inches (12.70 mm) to .625

inches (15.90 mm) to .625 inches (15.90 mm) and repeats. The start and stop space is in the middle of the

.50-inch holes. The horizontal spacing is 18.312 inches (465.1 mm), and the rack opening is specified as a

minimum of 17.75 inches (450 mm).

You need the following to install the Firepower 2100 in a rack using slide rails:

• Phillips screwdriver

• One slide rail kit (part number 800-103711-01) that contains the following:

The slide rail kit ships with the Firepower 2130/2140. You can order it for the

Firepower 2110/2120.

Note

• Left and right slides rails with two M3 x 6-mm Phillips screws (part number 48-101144-01)

• Two slide rail locking brackets (700-105350-02) with six 8-32 x 0.25-inch Phillips screws (part

number 48-101429-01)

• (Optional) Two cable management brackets (part number 700-106377-01) with four 8-32 x 0.375-inch

Phillips screws (part number 48-2696-01)

Slide rail assemblies work with four-post racks and cabinets with square slots, round 7.1mm holes, #10-32

threaded holes, and #12-24 threaded holes on the rack post front. The slide rail works with front to back

spacing of rack posts from 24 to 36 inches. The rack-mounting posts need to be 2 to 3.5-mm thick to work

with the slide rail rack mounting.

Safety Warnings

Take note of the following warnings:

Rack-Mount and Ground the Chassis

Rack-Mount the Chassis Using Slide Rails

Statement 1006—Chassis Warning for Rack-Mounting and Servicing

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions

to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing

the unit in the rack.

Warning

Statement 1024—Ground Conductor

This equipment must be grounded. To reduce the risk of electric shock, never defeat the ground conductor

or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate

electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.

Warning

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Statement 1047—Overheating Prevention

To reduce the risk of fire or bodily injury, do not operate the unit in an area that exceeds the maximum

recommended ambient temperature of: 40 degrees C

Warning

Statement 1073—No User-Serviceable Parts

There are no serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Step 1 Attach the slide-rail locking brackets to each side of the chassis using the six 8-32 x 0.375-inch Phillips screws (three

per side).

Rack-Mount and Ground the Chassis

Rack-Mount the Chassis Using Slide Rails

Figure 3: Attach the Slide-Rail Locking Bracket to the Side of the Chassis

Slide-rail locking bracket2Chassis1

—8-32 x 0.25-inch Phillips screws (three per side)3

Step 2 (Optional) Attach the cable management bracket to the slide-rail locking bracket:

a) Install the cable management screws into the slide-rail locking bracket.

Figure 4: Install the Cable Management Screws into the Slide-Rail Locking Bracket

b) Install two 8-32 x 0.375-inch Phillips screws through the inside of the slide-rail locking bracket to secure the cable

management bracket to slide-rail locking bracket.

Rack-Mount and Ground the Chassis

Rack-Mount the Chassis Using Slide Rails

Step 3 Attach the inner rails to the sides of the chassis:

a) Remove the inner rails from the slide rail assemblies.

b) Align an inner rail with each side of the chassis:

• (2110/2120) Install three 8-32 x 0.25-inch Phillips screws into each side of the chassis, and align the inner rail

so that the three slots on the rail line up with the screws on the chassis.

Figure 5: Line up the Inner Rail and Install the Screws on the 2110/2120 Chassis

M3 x 6 mm-Phillips screw (one per side)28-32 x 0.25-inch Phillips screws (3 per side)1

—Inner rail3

• (2130/2140) Align the inner rail so that the three slots on the rail line up with the three pegs on the side of the

chassis.

Figure 6: Line up the Inner Rail with the Pegs on the 2130/2140 Chassis

M3 x 6 mm-Phillips screw (one per side)2Mounting peg on the chassis for the keyed slot1

—Inner rail3

c) Set the keyed slots over the screws/pegs, and then slide the rail toward the front to lock it in place on the screw/pegs.

The rear key slot has a metal clip that locks over the screw/peg.

d) Using one M3 x 6-mm Phillips screw, secure the inner rail to the side of the chassis to prevent sliding.

e) Install the second inner rail to the opposite side of the chassis and secure with the other M3 x 6 mm screw.

Rack-Mount and Ground the Chassis

Rack-Mount the Chassis Using Slide Rails

Step 4 Open the front securing plate on both slide-rail assemblies. The front end of the slide-rail assembly has a spring-loaded

securing plate that must be open before you can insert the mounting pegs into the rack-post holes.

On the outside of the assembly, push the green arrow button toward the rear to open the securing plate.

Figure 7: Front Securing Mechanism Inside the Front End

Securing plate shown pulled back to open position2Front mounting pegs

Works with square slots, 7.1 mm holes, and

10-32 threaded holes.

Note

—Rack post3

Step 5 Install the slide rails into the rack:

a) Align one slide-rail assembly front end with the front rack-post holes that you want to use.

The slide rail front-end wraps around the outside of the rack post and the mounting pegs enter the rack-post holes

from the outside-front.

The rack post must be between the mounting pegs and the open securing plate.

Note

b) Push the mounting pegs into the rack-post holes from the outside-front.

c) Press the securing plate release button marked 'PUSH.' The spring-loaded securing plate closes to lock the pegs in

place.

d) Adjust the slide-rail length, and then push the rear mounting pegs into the corresponding rear rack-post holes. The

slide rail must be level front-to-rear.

The rear mounting pegs enter the rear rack-post holes from the inside of the rack post.

e) Attach the second slide-rail assembly to the opposite side of the rack. Make sure that the two slide-rail assemblies

are at the same height with each other and are level front-to-back.

f) Pull the inner slide rails on each assembly out toward the rack front until they hit the internal stops and lock in place.

Step 6 Insert the chassis into the slide rails.

a) Align the rear of the inner rails that are attached to the chassis sides with the front ends of the empty slide rails on

the rack.

b) Push the inner rails into the slide rails on the rack until they stop at the internal stops.

Rack-Mount and Ground the Chassis

Rack-Mount the Chassis Using Slide Rails

c) Slide the release clip toward the rear on both inner rails, and then continue pushing the chassis into the rack until the

mounting brackets meet the front of the slide rail.

Figure 8: Inner Rail Release Clip

Inner rail attached to chassis2Inner rail release clip1

Step 7 Use the captive screws on the front of the mounting brackets to fully secure the chassis to the rack.

What to do next

• See Ground the Chassis, on page 9 for the procedure to ground the Firepower 2100.

• Install the cables according to your software configuration as described in the Cisco Firepower 2100

Getting Started Guide.

Ground the Chassis

Grounding the chassis is required, even if the rack is already grounded. A grounding pad with two threaded

M4 holes is provided on the chassis for attaching a grounding lug. The grounding lug must be Nationally

Recognized Testing Laboratory (NRTL)-listed. In addition, a copper conductor (wires) must be used and the

copper conductor must comply with National Electrical Code (NEC) code for ampacity.

Note

You need the following items that you provide:

• Wire-striping tool

• Crimping tool

Rack-Mount and Ground the Chassis

Ground the Chassis

• Grounding cable

• Two star lock washers for the 10-32 x 0.375-inch screws used to secure the ground lug

• You need the following items from the accessory kit:

• Grounding lug #6 AWG, 90 degree, #10 post

• Two 10-32 x 0.375-inch screws used to secure the grounding lug

Safety Warnings

Take note of the following warnings:

Statement 1024—Ground Conductor

This equipment must be grounded. To reduce the risk of electric shock, never defeat the ground conductor

or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate

electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.

Warning

Statement 1046—Installing or Replacing the Unit

To reduce risk of electric shock, when installing or replacing the unit, the ground connection must always

be made first and disconnected last.

Warning

Statement 1025—Use Copper Conductors Only

To reduce risk of fire, use copper conductors only.

Warning

Step 1 Use a wire-stripping tool to remove approximately 0.75 inches (19 mm) of the covering from the end of the grounding

cable.

Step 2 Insert the stripped end of the grounding cable into the open end of the grounding lug.

Rack-Mount and Ground the Chassis

Ground the Chassis

Andere Handbücher für Firepower 2100 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Netzwerk-Hardware Handbücher

Cisco

Cisco Edge Concentrator MGX 8220 Referenzhandbuch

Cisco

Cisco 15530-LCMB-0200 - ESCON Multiplexing Line Card... Handbuch

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Bedienerhandbuch

Cisco

Cisco MGX 8260 Kurzanleitung

Cisco

Cisco Gigabit Switch Router Cisco 12012 Bedienungsanleitung

Cisco

Cisco WAVE-574-K9 - Wide Area Virtualization Engine... Handbuch

Cisco

Cisco ONS 15454 Bedienungsanleitung

Cisco

Cisco Aironet 340 Series Bedienungsanleitung

Cisco

Cisco LightStream 1010 Handbuch

Cisco

Cisco ISA550 Bedienungsanleitung

Cisco

Cisco 2650XM Bedienungsanleitung

Cisco

Cisco Firepower 2130 Wartungs- und Serviceanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco Catalyst 2960-XR Bedienungsanleitung

Cisco

Cisco MERAKI MX75 Bedienungsanleitung

Cisco

Cisco CWDM-OADM 1 Series Kurzanleitung

Cisco

Cisco Secure Network Server 3700 Series Handbuch

Cisco

Cisco 5400 Bedienungsanleitung

Cisco

Cisco ONS 15216-MD-40-ODD Bedienungsanleitung

Cisco

Cisco CRS-1 - Carrier Routing System Router Benutzerhandbuch

Cisco

Cisco UCS 6248 UP Bedienungsanleitung

Cisco

Cisco IDS 4210 - Intrusion Detection Sys 4210... Bedienungsanleitung

Cisco

Cisco Aironet 1040 Series Bedienungsanleitung

Cisco

Cisco CPS-MSP-1RU-K9 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung