Cisco 880 Series Bedienungsanleitung

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Installing Memory and Power Over Ethernet in

Cisco 880 Series and Cisco 890 Series Integrated

Services Routers

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.

Statement 1

This document describes how to install memory and Power over Ethernet (PoE) in a Cisco 880 series

and Cisco 890 series Integrated Services Routers (ISRs). It contains the following sections:

•Safety Warnings

•Installing Main Memory

•Installing Power Over Ethernet

•Opening the Chassis

•Closing the Chassis

Note Memory and PoE are the only upgradable options in the Cisco 880 series and Cisco 890 series ISRs. Do

not remove or install any other internal module.

Safety Warnings

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers

OL-16194-01

Installing Main Memory

Warning

Read the installation instructions before connecting the system to the power source. Statement 1004

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings,

necklaces, and watches). Metal objects will heat up when connected to power and ground and can

cause serious burns or weld the metal object to the terminals. Statement 43

Warning

Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF

or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,

detach the end away from the unit first. Statement 1026

Installing Main Memory

This section contains the following information:

•Items Shipped

•Installation Procedure

Items Shipped

Table 1 shows the items shipped with a DIMM unit.

Installation Procedure

To install a DIMM, follow these steps:

Step 1 Open the chassis according to the instructions in the “Opening the Chassis” section on page 8

Step 2 Locate the DIMM socket on the system board. See Figure 1 for the location of the DIMM socket.

Table 1 Items and Their Quantities Shipped with a DIMM Unit

Item Quantity

Memory module 1

ESD wrist strap 1

Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers

OL-16194-01

Installing Main Memory

Figure 1 DIMM Socket Location

Step 3 Remove any existing DIMM by gently pulling the spring-loaded clips on the end of the socket far enough

to release the DIMM, then gently pulling the DIMM up and away from the socket. See Figure 2.

1DIMM socket

270496

Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers

OL-16194-01

Installing Main Memory

Figure 2 Removing a DIMM

Step 4 Align the DIMM to the DIMM socket and insert the DIMM into the DIMM socket at a 45-degree angle,

as shown in Figure 3.

Figure 3 Installing a DIMM

Step 5 Gently push the DIMM down toward the system board, as shown in Figure 3, until it snaps into the

spring-loaded clips.

Step 6 Close the chassis according to the instructions in “Closing the Chassis” section on page 10.

1Spring-loaded clips 3DIMM socket

2DIMM

103155

1DIMM 3Spring-loaded clips

2DIMM socket

103154

Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers

OL-16194-01

Installing Power Over Ethernet

This section contains the following information:

•Items Shipped

•Installation Procedure

Items Shipped

The PoE option includes a PoE card, which must be installed inside the router, and an external power

supply.

Table 2 lists the items shipped with a PoE module.

Installation Procedure

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if

interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.

Avoid using such interconnection methods, unless the exposed metal parts are located within a

restricted access location and users and service people who are authorized within the restricted

access location are made aware of the hazard. A restricted access area can be accessed only through

the use of a special tool, lock and key or other means of security.

Statement 1072

To install the power supply card, perform the following steps:

Caution Ensure that the PoE power supply is not connected to the back of the router prior to installation of the

PoE card. Failure to do so may result in damage to the PoE card or to the router.

Step 1 Open the chassis according to the instructions in “Opening the Chassis” section on page 8.

Table 2 Items and Their Quantities Shipped with a PoE Module

Item Quantity

PoE PCBA 1

48-V PoE power supply adapter 1

Power supply cable 1

Standoffs with two notches 2

Standoff with one notch 1

Screws 3

ESD wrist strap 1

Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers

OL-16194-01

Installing Power Over Ethernet

Step 2 Locate the three metal standoff holes on the system board. See Figure 4 for the location of the PoE

connector. Two standoff holes are identified by a star pattern surrounding the hole; the third hole has a

screw attached to it.

Figure 4 PoE Connector

Step 3 Remove the screw from the third standoff hole.

1PoE connector 3Standoff hole with screw

2Standoff holes with star pattern

241979

Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers

OL-16194-01

Installing Power Over Ethernet

Step 4 Install the metal standoffs provided in the accessory kit as shown in Figure 5. Install the two metal

standoff that have two notches into the two star patterned standoff holes. Install the metal standoff that

has one notch into the third standoff hole. Use a 1/4-inch nut driver to tighten the standoff with one notch,

and a 3/16-inch nut driver to tighten the standoffs with two notches.

Caution Make sure that the standoffs are straight when installed. Tighten them gently but firmly. The shoulder of

each standoff must be seated tightly against the system board.

Figure 5 Installing the Power over Ethernet Card

1Standoff hole without star pattern 4Metal standoff with one notch

2Standoff holes with star pattern 5PoE card

3Metal standoffs with two notches 6Screws

247102

Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers

OL-16194-01

Opening the Chassis

Caution When installing the PoE card, ensure that the card is installed in the proper direction. Improper

installation will damage the PoE card. Installation of the PoE card requires the installation of three metal

standoffs, to which the card is then secured by using three screws. Be sure to use all three screws to

ensure that the card is installed properly.

Tip If the card is not installed in the correct direction, the three screw holes will not match up with the three

metal standoffs.

Step 5 Place the PoE card on top of the three metal standoffs, lining up the screw holes in the PoE card with the

metal standoffs.

Step 6 Push the PoE card down towards the system board until it is firmly fixed into the PoE connector.

Step 7 Insert the screws provided in the accessory kit through the PoE card and into the metal standoffs. See

Figure 5. Carefully tighten the screws with a Phillips screwdriver.

Step 8 Close the router (see Closing the Chassis, page 10), and then connect the PoE power supply to an AC

power outlet. To connect the PoE power supply to an AC power outlet, see the Cisco 860 Series,

Cisco 880 Series, and Cisco 890 Series Hardware Installation Guide, Connecting Power over Ethernet.

Opening the Chassis

To open the chassis, you will need a number-2 Phillips screwdriver, a wrist strap, and an antistatic mat.

Warning

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly

touch the backplane with your hand or any metal tool, or you could shock yourself.

Statement 94

Follow these steps to open the chassis:

Step 1 Disconnect the power supply cable.

Step 2 Disconnect all cables from the router back panel.

Step 3 Use the number-2 Phillips screwdriver to remove the screws at the middle on the back panel, and at the

sides of the router. Figure 6 shows the location of the screws. The screws are in the same location on all

Cisco 880 series ISRs.

Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers

OL-16194-01

Opening the Chassis

Figure 6 Chassis Screws Locations

Step 4 Place your hand on both sides of the router where the screws were located. With your fingers gently pry

the chassis cover outward and away from the router, and lift the chassis cover up. The front end of the

chassis cover will remain attached to the chassis. Figure 7 shows how to open the chassis.

1Locations of the screws

241976

Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers

OL-16194-01

Closing the Chassis

Figure 7 Opening the Chassis

Step 5 Place the router bottom on an antistatic mat.

Closing the Chassis

To close the chassis, you will need a number-2 Phillips screwdriver and a wrist strap.

Warning

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly

touch the backplane with your hand or any metal tool, or you could shock yourself.

Statement 94

241977

Andere Handbücher für 880 Series

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco uBR7100 Series Handbuch

Cisco

Cisco LinkSys RTP300 Original Betriebsanleitung

Cisco

Cisco ASR 903 Anleitung zur Verwendung

Cisco

Cisco 910 Bedienungsanleitung

Cisco

Cisco ASR 5000 Bedienungsanleitung

Cisco

Cisco 7603 - Modular Expansion Base Bedienungsanleitung

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Bedienungsanleitung

Cisco

Cisco 2811 - Voice Security Bundle Router Bedienungsanleitung

Cisco

Cisco SN 5428-2 Anleitung zur Verwendung

Cisco

Cisco ASR 903 Bedienungsanleitung

Cisco

Cisco Firepower 1120 Handbuch

Cisco

Cisco Linksys EA2700 Bedienungsanleitung

Cisco

Cisco SRW208MP Bedienungsanleitung

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Bedienungsanleitung

Cisco

Cisco ASR 5000 Series Bedienungs- und Sicherheitshinweise

Cisco

Cisco ASR-920-8S4Z-PD Handbuch

Cisco

Cisco 2600 Series Bedienungsanleitung

Cisco

Cisco 10008 Handbuch

Cisco

Cisco Card Cage and Backplane 7513-MX Bedienungsanleitung

Cisco

Cisco 7507 Bedienungsanleitung

Cisco

Cisco ME-4924-10GE Handbuch

Cisco

Cisco WRT54G Bedienungsanleitung

Cisco

Cisco ME 3400G-2CS - Ethernet Access Switch Bedienungsanleitung

Cisco

Cisco ASR 902U Handbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung