Cisco ASR 5000 Bedienungs- und Wartungshandbuch

Installation Procedure Overview

This chapter briefly describes the steps and tools that are required for the physical installation of the chassis.

It includes the following sections:

•Chassis Components, page 2

•Installation at a Glance, page 3

•Required Tools and Equipment, page 4

•Site Prerequisites, page 5

•Protecting Against Electro-static Discharge, page 5

•Federal Communications Commission Warning, page 6

ASR 5000 Installation Guide

Chassis Components

The following graphic and table illustrate the chassis and describe its subcomponents.

Figure 1: ASR 5000 Chassis and Sub-components

Table 1: Chassis and Sub-component Identification Key

DescriptionItem

Chassis: Supports 16 front-loading slots for application cards and 32 rear-loading slots for line

cards. The chassis ships with blanking panels over every slot except the following: 1, 8, 17, and

24. These are intentionally left uncovered for the initial installation of system components.

Mounting brackets: Supports installation in a standard 19-inch rack or telecommunications cabinet.

Standard and mid-mount options are supported. In addition, each bracket contains an electro-static

discharge jack for use when handling equipment.

Upper fan tray: Draws air up through the chassis for cooling and ventilation and exhausts the air

through the vents at the upper-rear of the chassis.

ASR 5000 Installation Guide

Installation Procedure Overview

Chassis Components

DescriptionItem

Upper bezel: Covers the upper fan tray bay.4

Lower fan tray cover/EMI shield: Secures the lower fan tray assembly in place and serves as an

EMI shield. The cover also provides an air baffle allowing air to enter into the chassis.

Lower bezel: Covers the lower fan tray bay.6

Lower fan tray assembly: Draws air into the chassis through the chassis' front and sides for cooling

and ventilation. It is equipped with a particulate air filter to prevent dust and debris from entering

the system.

Power Filter Units (PFUs): Each of the system's two 165 amp PFUs provides -48 VDC power to

the chassis and its associated cards. Each load-sharing PFU operates independently from the other

to ensure maximum power feed redundancy.

Installation at a Glance

The list below summarizes the installation process for the chassis.

Unpacking instructions are not provided in this document. Please refer to the Unpacking the ASR 5000

Chassis document shipped with the system, for information and instructions on this topic. The chassis

and cards are shipped separately.

Note

•Unpack the chassis and cards

•Determine which chassis mounting option to use: standard or mid-mount.

•Install the chassis into a standard 19-inch equipment rack or telecommunications cabinet.

•Connect the chassis to earth ground.

•Install application cards into the front of the chassis.

•Install line cards into the rear of the chassis.

•Connect data cables to the line cards.

•Connect power cables to the chassis.

•Apply power to the chassis.

•Verify that the installation was successful.

Once the installation has been validated, you will be directed to the System Administration Guide for instructions

on how to configure the system for operation.

ASR 5000 Installation Guide

Installation Procedure Overview

Installation at a Glance

Required Tools and Equipment

This section lists the tools and equipment needed for installation.

Hand Tools

The following hand tools are required for installation of the chassis, application and line cards, fan tray

assemblies, and power filter units:

•Phillips #1 and #2 hand screwdrivers. Used to tighten thumb-screws on cards, fan tray assemblies, PFUs,

and mounting brackets.

The inappropriate use of electric or pneumatic torque drivers, or power drill/impact

drivers to loosen or tighten fasteners may result in damage to system components.

Caution

•9/16-inch nut driver or ratchet and socket set. Used to connect power and return cables.

•3/8-inch nut driver or ratchet and socket set. Used to connect grounding cables.

•Torque wrench (rated 50 in-lb [5.65 N-m]) with 9/16-inch socket for tightening lugs to power terminals.

•Grounding wrist and/or heel straps. Used to prevent Electro-Static Discharge (ESD) as discussed in the

Protecting Against Electro-static Discharge section that follows.

During installation, maintenance, and/or removal, wear grounding wrist and/or heel straps to avoid ESD

damage to the components. Failure to do so could result in damage to sensitive electronic components

and potentially void your warranty.

Caution

Equipment

The following equipment is necessary to install the chassis and verify that it is ready for configuration:

•Standard 19-inch (48.26 cm) equipment rack or telecommunications cabinet with mounting hardware.

Additional hardware, such as extension brackets (not supplied), may be used to install the chassis in a

standard 23-inch (58.42 cm) cabinet or rack.

•Voltmeter to measure input voltages at the PFU terminals.

•Heat gun for installing shrink wrap tubing over power cable lugs.

•Console cable supplied with the Switch Processor I/O (SPIO) line card.

•A computer or terminal server with a 9-pin RS-232C serial port, or 25-to-9-pin male RS-232C adapter.

It will be connected to the SPIO's Console port for accessing the command line interface (CLI) for initial

system configuration.

ASR 5000 Installation Guide

Installation Procedure Overview

Required Tools and Equipment

•Pallet jack and/or chassis lift to move and position the ASR 5000 chassis. Without such mechanical

assistance, moving and positioning the chassis will require multiple craftpersons trained to safely handle

heavy rack-mounted units.

Site Prerequisites

This section summarizes power, grounding, environment, and clearance requirements that must be met prior

to installing and operating the ASR 5000. For detailed information, refer to the Technical Specifications

chapter.

Power and Grounding

Each PFU requires a power feed of 160A @ -48VDC (nominal). The feeds should be routed to the installation

rack from the site power supply using adequately sized conductors and circuit breakers in accordance with

local electrical codes.

The chassis must be grounded to a site ground point using the recommended conductors and lugs. The ground

point should be in close proximity to the ASR 5000 chassis to assure adequate conductivity.

Environment

The site's heating ventilation and air conditioning (HVAC) systems must be sized to maintain the operating

temperatures and relative humidity specified in the Technical Specifications chapter. HVAC capacity

requirements will vary based on the system configuration and associated power draw, as well as the operational

characteristics of other equipment installed at the site.

Clearance

Adequate clearance must be maintained at the front and rear of the ASR 5000 chassis to assure proper air

flow and allow maintenance access for the installation, removal and replacement of components. The

recommended clearance is 30 to 36 inches (76 to 92 centimeters) at the front and rear of the chassis.

Protecting Against Electro-static Discharge

Electro-Static Discharge (ESD) can cause serious damage to sensitive components on the chassis, its

sub-components, and/or the cards installed in the chassis. To prevent damage from ESD, you must take proper

grounding precautions before handling the chassis or any of its components.

To aid in the prevention of ESD damage, the chassis and its mounting brackets are equipped with ESD jacks.

Use the jacks in conjunction with grounding wrist straps when handling the chassis and/or its components.

The following figure shows the location of the jacks.

ASR 5000 Installation Guide

Installation Procedure Overview

Site Prerequisites

Before using the ESD jacks on the chassis and its mounting brackets to provide protection, you must first

connect the chassis to earth ground as described in the Chassis Installation chapter of this document.

Important

Figure 2: Location of Chassis ESD Jacks

Federal Communications Commission Warning

This device complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules and

Regulations. Operation is subject to the following two conditions:

ASR 5000 Installation Guide

Installation Procedure Overview

Federal Communications Commission Warning

•This device may not cause harmful interference.

•This device must withstand any interference received, including interference that may cause undesired

operation.

The system platform has been tested and found to comply with the limits for a Class A digital device pursuant

to Part 15 of the FCC Rules and Regulations. These limits are designed to provide reasonable protection

against harmful interference when this equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio and television communications. Operation of this

equipment in a residential area is likely to cause interference in which case the user will be required to correct

the interference at his or her own expense.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority

to operate the product.

Shielded cables must be used with this unit to ensure compliance with the FCC Class A limits.

ICS Notice

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Laser Notice

The lasers in this equipment are Class 1 devices. Class 1 laser devices are not considered to be hazardous.

ASR 5000 Installation Guide

Installation Procedure Overview

ICS Notice

ASR 5000 Installation Guide

Installation Procedure Overview

Laser Notice

Andere Handbücher für ASR 5000

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco Catalyst 3550 Series Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

Cisco

Cisco 2600 Series Bedienungsanleitung

Cisco

Cisco 836 Handbuch

Cisco

Cisco Linksys WET610N Bedienungsanleitung

Cisco

Cisco 1760 - VPN Bundle Router Bedienungsanleitung

Cisco

Cisco CRS-1 - Carrier Routing System Router Bedienungsanleitung

Cisco

Cisco 815 Bedienungsanleitung

Cisco

Cisco SFE1000P - Small Business Managed Switch Bedienungsanleitung

Cisco

Cisco NCS 540 Series Bedienungsanleitung

Cisco

Cisco PRE1s Bedienungsanleitung

Cisco

Cisco IR829 Handbuch

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco ASR 1000 Series Bedienungsanleitung

Cisco

Cisco N5010P-N2K-BE Bedienungsanleitung

Cisco

Cisco 2620 Bedienungsanleitung

Cisco

Cisco RV016 - Small Business - 10/100 VPN Router Bedienungsanleitung

Cisco

Cisco MWR 1941-DC - 1941 Mobile Wireless Router Bedienungsanleitung

Cisco

Cisco 10000 Series Bedienungsanleitung

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Bedienungsanleitung

Cisco

Cisco Network Convergence System 540 Handbuch

Cisco

Cisco ACE-4710-K9 Bedienungsanleitung

Cisco

Cisco WRT300N Bedienungsanleitung

Cisco

Cisco Linksys SGE2010P Handbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung