Cisco IR829 Bedienungsanleitung

CHAPTER

2-3

Cisco IR800 Integrated Services Router Software Configuration Guide

Product Overview

This chapter provides an overview of the features available for the Cisco IR800 Integrated Services

Routers (ISRs) and contains the following sections:

•General Description, page 2-3

•Hardware Overview, page 2-4

–

IR829 Product Overview, page 2-4

–

IR809 Product Overview, page 2-8

–

Reset Button, page 2-11

•Software Overview, page 2-13

•Hardware Differences Between IR809, IR829, and the C819HG, page 2-14

•Antenna Recommendations, page 2-16

•Features Supported in Different IOS Releases, page 2-16

•Related Documentation, page 2-17

General Description

The 800 Series Industrial Integrated Services Routers are compact, ruggedized, Cisco IOS Software

routers. They offer support for integrated 4G LTE wireless WAN (both 809 and 829 models) and wireless

LAN capabilities (829 model only). The IR829 offers an Internal WLAN Access Point which runs

on-board the router. The AP803 runs its own IOS software independently from the IR829 IOS, and

requires configuring. The AP803 works as a standalone access point or with a wireless controller.

They offer:

•Easily and rapidly deployable

•Highly available, highly secure, and reliable

•Designed for machine-to-machine (M2M) communication and for mobile vehicle communication in

harsh environmental conditions

•Designed to withstand hostile environments, tolerating a wide temperature range

These industrialized routers deliver enterprise-class features, including highly secure data, voice, and

video communications to stationary and mobile network nodes across wired and wireless links. They can

deliver enterprise-grade, wireline-like functionality.

2-4

Cisco IR800 Integrated Services Router Software Configuration Guide

Chapter 2 Product Overview

Hardware Overview

The routers also support Cisco IOx Software, providing an open, extensible environment for hosting

additional operating systems and applications directly at the network edge. They can enhance other

Cisco IoT System products across multiple industries, including transportation, manufacturing,

electrical utilities, and others.

For a complete listing of the routers capabilities, see the Cisco 829 Industrial Integrated Services Routers

Product Information.

Hardware Overview

This section covers the overview of the IR809 and IR829.

IR829 Product Overview

Figure 2-1 shows the IR829.

Figure 2-1 Cisco IR829 Integrated Services Router

Figure 2-2 shows the front panel details of the Cisco IR829 Single Modem.

Figure 2-2 Cisco IR829 Front Panel Single Modem

2-5

Cisco IR800 Integrated Services Router Software Configuration Guide

Chapter 2 Product Overview

Hardware Overview

Figure 2-3 shows the front panel details of the Cisco IR829 Dual Modem.

Figure 2-3 Cisco IR829 Front Panel Duel Modem

Figure 2-4 shows the back panels details of the Cisco IR829 Single Modem.

Figure 2-4 Cisco IR829 Back Panel Single Modem

1CELLULAR 0 AUX 5Serial Ports

2Limited Modularity Slot 6USB-A Port

3Gigabit WAN (SFP) 7Power Input, Battery, and Ignition connector.

Refer to the DC Power section for pin-outs.

4Gigabit Ethernet LAN/PoE (RJ45) 8WLAN ANT 0 2.4GHz

1CELLULAR 0 AUX 5Serial Ports

2Limited Modularity Slot 6USB-A Port

3Gigabit WAN (SFP) 7Power Input, Battery, and Ignition connector.

Refer to the DC Power section for pin-outs.

4Gigabit Ethernet LAN/PoE (RJ45) 8WLAN ANT 0 2.4/5GHz

2-6

Cisco IR800 Integrated Services Router Software Configuration Guide

Chapter 2 Product Overview

Hardware Overview

Figure 2-5 shows the back panels details of the Cisco IR829 Dual Modem.

Figure 2-5 Cisco IR829 Back Panel Dual Modem

Note Behind the SIM Door Assembly, there is a reset switch (1), Mini USB console port (2), and Dual SIM

slots (3). See Figure 2-6 for details

1WLAN ANT 0 5GHz 5Denotes SIM card order, SIM0 on top and

SIM1 on bottom.

2WLAN ANT 1 2.4GHz 6WLAN ANT 1 5GHz

3Cover over SIM cards, reset button and

console port cover, see Figure 2-6

7CELLULAR 0 MAIN

4GPS SMA

1Cellular 1 Main 5Denotes SIM card order, SIM0 on top and

SIM1 on bottom.

2WLAN ANT 1 2.4/5GHz 6Cellular 1 AUX

3Cover over SIM cards, reset button and

console port cover, see Figure 2-6

7CELLULAR 0 MAIN

4GPS SMA

2-7

Cisco IR800 Integrated Services Router Software Configuration Guide

Chapter 2 Product Overview

Hardware Overview

Figure 2-6 Behind the SIM Door

Figure 2-7 shows the top of the Cisco IR829.

Figure 2-7 Cisco IR829 Top Cover

Figure 2-8 shows the LED detail from the Dual Modem SKU. Single Modem SKUs will only have

Cellular0 LEDs.

2-8

Cisco IR800 Integrated Services Router Software Configuration Guide

Chapter 2 Product Overview

Hardware Overview

Figure 2-8 Cisco IR829 LED Detail

IR809 Product Overview

Figure 2-1 shows the IR809.

Figure 2-9 Cisco IR809 Integrated Services Router

Figure 2-2 shows the front panel details of the Cisco IR809.

2-9

Cisco IR800 Integrated Services Router Software Configuration Guide

Chapter 2 Product Overview

Hardware Overview

Figure 2-10 Cisco IR809 Front Panel

Note LEDs are viewable from the top and from the front of the IR809.

Figure 2-4 shows the back panels details of the Cisco IR809.

1S0 RS232 DCE/RS485 Combo Port 8Grounding Point

2S1 RS232 DTE only 9Mini type-B USB console/debug port

3GE0 (10/100/1000) 10 SYS LED

4GE1 (10/100/1000) 11 Alarm LED

5USB 2.0 (Type-A Host Port) 12 WAN/WWAN LEDs

6RESET Button 13 SIM Card LEDs

7DC Power/Alarm Connector

2-10

Cisco IR800 Integrated Services Router Software Configuration Guide

Chapter 2 Product Overview

Hardware Overview

Figure 2-11 Cisco IR809 Back Panel

Figure 2-12 shows the back panels details of the Cisco IR809.

1DIV TNC connector for 4G Modem

2SMA connector for GPS

3SIM0 and SIM1 Card Slots

4MAIN TNC connector for 4G Modem

2-11

Cisco IR800 Integrated Services Router Software Configuration Guide

Chapter 2 Product Overview

Hardware Overview

Figure 2-12 Cisco IR809 Top Cover

Note See the respective Hardware Installation Guides for detailed description of the LEDs.

Reset Button

The reset button resets the router configuration to the default configuration set by the factory. To restore

the router configuration to the default configuration set by the factory, use a standard size #1 paper clip

with wire gauge 0.033 inch or smaller and simultaneously press the reset button while applying power

to the router.

Note On the IR829, the rear cover must be removed to expose the reset switch.

Starting with release 15.6(1)T, the IR809 and IR829 have changed the way the reset button works. The

IR800 series platforms now perform in the same manner as the C819. The high level description of the

functionality works like this:

•Press and hold the reset button while powering up the router

•During warm reboot this button has no impact on performance

•Simply pressing the button at any time does not reset the router

•The router will not react to the reset button if it is pressed after power-up because the button needs

to be pushed before turning ON/inserting power – to make sure that the condition is detected.

•The push-button cannot be used to boot a IOS image from network. The golden image has to be on

flash: only

2-12

Cisco IR800 Integrated Services Router Software Configuration Guide

Chapter 2 Product Overview

Hardware Overview

Note For the location of the reset button see the appropriate IR809 or IR829 Hardware Installation Guide.

Perform the following steps to use this feature:

Step 1 Unplug power.

Step 2 Press the reset button on the router.

Step 3 Power up the system while holding down the reset button.

The system LED blinks four times indicating that the router has accepted the button push.

Tip The IR800 series of routers do not support password recovery. If needed, use the above procedure to

bring the router to its initial configuration, or to a previously set backup configuration.

Booting a Default IOS Image and Default Configuration

The IR800 differs from traditional IOS routers when booting a default IOS image and a default

configuration. These steps apply on a device running 15.6(1)T or later.

Method 1:

Step 1 Save a copy of your IR800 IOS image with the .default extension on flash. For example:

ios-image.default.

Step 2 Save a copy of your IR800 Hypervisor image with the .default extension on bootstrap. For example:

hypervisor-image.default.

Step 3 Save your desired default configuration file with the .cfg extension on flash. For example: config.cfg.

Step 4 Reset your IR800 router by powering it down, then press and hold the RESET button while powering up

the device.

The IR800 router will automatically boot hypervisor-image.default, then ios-image.default, and load the

config.cfg.

Step 5 Make sure there exists only one IOS image with a .default extension, only one configuration file with

the .cfg extension on the flash, and only one hypervisor image with the .default extension on bootstrap.

If you do not have a config.cfg on flash, it will boot with the Cisco default configuration (aka: empty)

startup-config.

Method 2:

Step 1 Check the “boot system” setting configuration in the default configuration file (prior to saving it to

startup-config), and verify that it points to an existing IOS image on the flash: partition.

Andere Handbücher für IR829

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco 3825 Series Kurzanleitung

Cisco

Cisco 2621 Bedienungsanleitung

Cisco

Cisco Nexus 9000 Series Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco 815 Handbuch

Cisco

Cisco Cisco 887 Bedienungsanleitung

Cisco

Cisco RV260 series Bedienungsanleitung

Cisco

Cisco 860 Series Handbuch

Cisco

Cisco SN 5428-2 Anleitung zur Verwendung

Cisco

Cisco 1710 Bedienungsanleitung

Cisco

Cisco CISCO827 Bedienungsanleitung

Cisco

Cisco IR809 Bedienungs- und Sicherheitshinweise

Cisco

Cisco Linksys WET610N Bedienungsanleitung

Cisco

Cisco uBR900 Series Bedienungsanleitung

Cisco

Cisco 7246VXR - uBR Router Bedienungsanleitung

Cisco

Cisco SR520-FE-K9 Bedienungsanleitung

Cisco

Cisco 3600 Series Kurzanleitung

Cisco

Cisco 800 Series Anleitung zur Verwendung

Cisco

Cisco ASA 5508-X Bedienungsanleitung

Cisco

Cisco WUMC710 Bedienungsanleitung

Cisco

Cisco QuickVPN - PC Bedienungsanleitung

Cisco

Cisco Cisco 881 Bedienungsanleitung

Cisco

Cisco 860 Series Handbuch

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Kurzanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung