Cisco Small Business RV320 Bedienungsanleitung

Quick Start Guide

Cisco Small Business

RV320/RV325 Gigabit Dual WAN VPN Router

Package Contents

•RV320/RV325 Gigabit Dual WAN VPN Router

•Ethernet Cable

•Power Adapter

•Quick Start Guide

•Documentation and software on CD-ROM

2 Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide

Welcome

Thank you for choosing the Cisco Small Business RV320/RV325 Gigabit

Dual WAN VPN Router.

This guide describes how to physically install your Cisco RV320/RV325

and launch the web-based Device Manager.

Installing Cisco RV320/RV325

To prevent the device from overheating or being damaged:

•Ambient Temperature—Do not operate it in an area that exceeds an

ambient temperature of 104°F (40°C).

•Air Flow—Be sure that there is adequate air flow around the device. If

wall mounting the firewall, make sure the heat dissipation holes are to

the side.

•Circuit Overloading—Adding the device to the power outlet must not

overload that circuit.

•Mechanical Loading—Be sure that the device is level and stable to

avoid any hazardous conditions and that it is secure to prevent it from

sliding or shifting out of position. Do not place anything on top of the

firewall, as excessive weight might damage it.

For desktop mounting, place the device on a flat surface so that it sits on its

four rubber feet.

Wall Mounting

The router has two wall-mount slots on the bottom panel. To mount the

router on a wall, you need mounting hardware (not included). Suggested

hardware is illustrated below (not true to scale).

RV320

Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide 3

RV325

WARNING Insecure mounting might damage the router or cause injury.

Cisco is not responsible for damages incurred by insecure wall-

mounting.

WARNING

For safety, ensure that the heat dissipation holes are facing

sideways

STEP 1Drill two pilot holes, approximately 109 mm apart, into the surface.

STEP 2Insert a screw into each hole, leaving a gap between the surface

and the base of the screw head of 1 to 1.2 mm.

STEP 3Place the router wall-mount slots over the screws and slide the

router down until the screws fit snugly into the wall-mount slots.

4 Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide

Cisco RV320 Features

Front Panel

PWR—Lit to indicate the unit is powered on and booted. Blinks when the

device is booting.

VPN—Lit green when the designated VPN tunnel is up. Blinks green when

data is being sent or received through the tunnel. Lit amber when the

tunnel is disconnected. Blinks amber when attempting to establish the

tunnel.

DMZ—Lit green when the DMZ/WAN port is configured as a DMZ.

DIAG—Blinks red when the firmware is updating. Lit red when the device

is booting.

LINK/ACT—Lit steady when a link between a port and another device is

detected. Flashes when a port is passing traffic.

GIGABIT—Lit when another device is connected to a port and a

1000 Mbps link is established. Off when the connection speed is under

1000 Mbps or no other device is attached to a port.

LAN 1-4—Lit when the LAN ports on the back panel are linked to another

device. Blinks when passing traffic.

DMZ/WAN—Lit when a device is connected to the DMZ/WAN port.

Flashes when sending or receiving data over the WAN DMZ port.

WAN—Lit when the WAN port is connected. The light is off when it is not

connected to the Internet or it is connected by using a USB dongle. Blinks

when it is sending or receiving data over the WAN connection.

USB 1 and USB 2—Lit green when the corresponding port is connected

to a device. Flashes green when the port is sending or receiving data.

RESET—Reboot or reboot and restore defaults:

•To reboot the unit and retain the current configuration, press and hold

RESET for at least 3, but no more than 10 seconds, by using a paper

clip or a pen tip.

•To reboot the unit and restore the factory default configuration, press

and hold in the RESET button for more than 10 seconds. Changes you

have made to the configuration of your device are lost.

Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide 5

Back Panel

POWER—Toggles power to the device on or off.

12VDC (1.5A)—Power port that connects the device to the provided

12VDC, 1.5 amp power adapter.

LAN (1-4)—RJ-45 connectors that link local area network devices, such as

PCs, print servers, or switches, to the device.

DMZ/WAN—Internet device connection supporting a DMZ for connecting

the device to a wide area network device, such as a cable or DSL modem.

WAN—Internet connection for connecting the device to a wide area

network device, such as a cable or DSL modem.

USB 1—Type A USB port that supports flash drives and 3G/4G/LTE USB

dongles. Caution: Use only the power supply provided with the device;

using another power supply might cause the USB dongle to fail.

Side Panel

USB 2—Type A USB port that supports flash drives and 3G/4G/LTE USB

dongles. Caution: Use only the power supply provided with the device;

using another power supply might cause the USB dongle to fail.

Cisco RV325 Features

Front Panel

PWR—Lit to indicate the unit is powered on and booted. Blinks when the

device is booting.

VPN—Lit green when the designated VPN tunnel is up. Blinks green when

data is being sent or received through the tunnel. Lit amber when the

tunnel is disconnected. Blinks amber when attempting to establish the

tunnel.

DMZ—Lit green when the DMZ/WAN port is configured as a DMZ.

DIAG—Blinks red when the firmware is updating. Lit red when the device

is booting.

USB 1 and USB 2—Lit green when the corresponding port is connected

to a device. Flashes green when the port is sending or receiving data.

LAN 1-14—RJ-45 connectors that link local area network devices, such as

PCs, print servers, or switches, to the device.

WAN—Lit when the WAN port is connected. The light is off when it is not

connected to the Internet or it is connected by using a USB dongle. Blinks

when it is sending or receiving data over the WAN connection.

6 Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide

DMZ/WAN—Lit when a device is connected to the DMZ/WAN port.

Flashes when sending or receiving data over the WAN DMZ port.

LINK/ACT—Lit steady when a link between a port and another device is

detected. Flashes when a port is passing traffic.

GIGABIT—Lit when another device is connected a port and a 1000 Mbps

link is established. Off when the connection speed is under 1000 Mbps or

no other device is attached to a port.

USB 1—Type A USB port that supports flash drives and 3G/4G/LTE USB

dongles. Caution: Use only the power supply provided with the device;

using another power supply might cause the USB dongle to fail.

RESET—Reboot or reboot and restore defaults:

•To reboot the unit and retain the current configuration, press and hold

RESET for at least 3, but no more than 10 seconds, by using a paper

clip or a pen tip.

•To reboot the unit and restore the factory default configuration, press

and hold in the RESET button for more than 10 seconds. Changes you

have made to the configuration of your device are lost.

Back Panel

POWER—Toggles power to the device on or off.

12VDC (2A)—Power port that connects the device to the provided

12VDC, 2 amp power adapter.

Side Panel

USB 2—Type A USB port that supports flash drives and 3G/4G/LTE USB

dongles. Caution: Use only the power supply provided with the device;

using another power supply might cause the USB dongle to fail.

Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide 7

Connecting

You must connect a configuration terminal (PC) to the device by using a

LAN port. The terminal must be in the same wired subnetwork as the

device to perform the initial configuration. As part of the initial

configuration, the device can be configured to allow remote management.

To connect a computer to the device:

STEP 1Power off all equipment, including the cable or DSL modem, the

computer, and this device.

STEP 2Use an Ethernet cable to connect your cable or DSL modem to the

WAN port on this device.

STEP 3Connect another Ethernet cable from one of the LAN (Ethernet)

ports to the Ethernet port on the computer.

STEP 4Power on the WAN device and wait until the connection is active.

STEP 5Connect the power adapter to the 12VDC port of this device.

CAUTION Use only the power adapter that is supplied with the device.

Using a different power adapter could damage the device or

cause the USB dongles to fail.

The POWER switch is on by default. The power light on the front

panel is lit when the power adapter is connected properly and the

device is finished booting.

STEP 6Plug the other end of the adapter into an electrical outlet. Use the

plug (supplied) specific to your country.

STEP 7Power on the computer that you connected to the LAN port in

Step 3. Your computer becomes a DHCP client of the device and

receives an IP address in the 192.168.1.xxx range.

8 Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide

Logging In

To l o g i n t o t h e d e v i c e :

STEP 1Launch a web browser.

STEP 2In the address bar, enter the default IP address of the device,

https://192.168.1.1. A site security certificate message is

displayed. The Cisco RV320/RV325 uses a self-signed security

certificate. This message appears because the device is not

known to your computer.

STEP 3Click Continue to this website (or the option shown on your

particular web browser) to continue. The login displays.

STEP 4Enter the username and password. The default username is cisco.

The default password is cisco. Passwords are case sensitive.

STEP 5Click Log In. The Device Manager application starts.

We recommend that you change the password. You are required to

change the password before enabling features such as remote

management.

Changing the Administrator Username and Password

To change the Administrator username and password on the device:

STEP 1From the Getting Started page, select Change Administrator

Password or select Setup > Password from the navigation bar.

STEP 2Change the Username.

STEP 3Enter the Old Password.

STEP 4Enter the New Password.

STEP 5Confirm the New Password.

STEP 6Click Save.

Troubleshoot Your Connection

If you cannot access your device by using Device Manager, the device

might not be reachable from your computer. You can test network

connections by using ping on a computer running Windows:

STEP 1Open a command window by using Start > Run and enter cmd.

STEP 2At the Command window prompt, enter ping and the device IP

address. For example, ping 192.168.1.1 (the default static IP

address of the device).

Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide 9

If you can reach the device, you should get a reply similar to the

following:

Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time<1ms TTL=128

If you cannot reach the device, you should get a reply similar to the

following:

Pinging 192.168.1.1 with 32 bytes of data:

Request timed out.

Possible Causes and Resolutions

Bad Ethernet connection:

Check the LEDs for the proper indications. Check the connectors of the

Ethernet cable to ensure they are firmly plugged into the device and

your computer.

Wrong or conflicting IP address:

Verify that you are using the correct IP address of the device.

Verify that no other device is using the same IP address as this device.

No IP route:

If the device and your computer are in different IP subnetworks,

remote access must be enabled and you need at least one router on

the network to route the packets between the two subnetworks.

Unusually long access time:

Adding new connections might take 30 to 60 seconds for the affected

interfaces and/or LAN to become operational.

Where to Go From Here

Support

Cisco Small Business

Support Community

www.cisco.com/go/smallbizsupport

Cisco Small Business

Support and Resources

www.cisco.com/go/smallbizhelp

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706 USA

www.cisco.com

Small Business Support, Global:

www.cisco.com/go/sbsc

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates

in the U.S. and other countries. To view a list of Ciscotrademarks, go to this URL:

www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their

respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (1110R)

78-20927-03

Phone Support Contacts www.cisco.com/en/US/support/

tsd_cisco_small_business

_support_center_contacts.html

Cisco Small Business

Firmware Downloads

www.cisco.com/cisco/software/

navigator.html?i=!ch

Select a link to download firmware for Cisco

Small Business Products. No login is

required.

Product Documentation

Cisco Small Business

Routers and Firewalls

www.cisco.com/go/smallbizrouters

Cisco Small Business

Cisco Partner Central

for Small Business

(Partner Login Required)

www.cisco.com/web/partners/sell/smb

Cisco Small Business

Home

www.cisco.com/smb

Andere Handbücher für Small Business RV320

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco ASR 9000 Series Merkblatt

Cisco

Cisco 4451-X Handbuch

Cisco

Cisco 2612 Handbuch

Cisco

Cisco Card Cage and Backplane 7513-MX Leitfaden

Cisco

Cisco E-Series Bedienungsanleitung

Cisco

Cisco 7600 Series Bedienungsanleitung

Cisco

Cisco ASR 1002-X Installationsanleitung

Cisco

Cisco ASR 1000 Series Bedienungsanleitung

Cisco

Cisco Profile Series Bedienungsanleitung

Cisco

Cisco NCS 4216 Bedienungsanleitung

Cisco

Cisco Linksys E-Series Installationsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco 800 Series Handbuch

Cisco

Cisco 850 Series Bedienungsanleitung

Cisco

Cisco ASR 5000 Series Bedienungsanleitung

Cisco

Cisco 1811W - Integrated Services Router Wireless Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco MWR 1941-DC - 1941 Mobile Wireless Router Bedienungsanleitung

Cisco

Cisco WRT54GR Bedienungsanleitung

Cisco

Cisco 1840 Originalbetriebsanleitung

Cisco

Cisco NCS 540 Handbuch

Cisco

Cisco SOHO 97 Bedienungsanleitung

Cisco

Cisco MGX 8230 Bedienungs- und Wartungsanleitung

Cisco

Cisco 819 series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung