Cisco Small Business SRP520-U Bedienungsanleitung

Quick Start Guide

Cisco SRP500 Series Services Ready Platforms

(SRP520-U Models)

Package Contents

•Cisco SRP520-U Series Services Ready Platform

•RJ-45 Ethernet Cable

•RJ-11 Telephone Cable

•Power Clip and Adapter

•Quick Start Guide

•Product CD

2 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520-U Models)

Welcome

Thank you for choosing Cisco SRP500 Series Services Ready Platforms.

The SRP520-U Series are flexible devices that enable small businesses to

connect to high quality data, hosted voice, and security services offered

by service providers.

This guide describes how to physically install the SRP and perform the

initial configuration.

Before You Begin

Minimum Requirements

•Computer running Microsoft Internet Explorer 7.0 or later, or Mozilla

Firefox 3.6. or later.

•Active Internet connection.

•(Optional) Analog phone line.

•(Optional) Telephone handset, fax machine, or PBX line for connecting

to the voice ports.

•Cables

– RJ-45 Ethernet cables (Category 5 or higher) for connecting

computers, WAN and LAN interfaces, phones, or other devices.

– RJ-11 telephone cable for analog line (FXO) and phone (FXS)

connections.

– ADSL splitter, if required by your Service Provider.

•(Optional) Mobile Broadband USB Modem.

Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520-U Models) 3

Default Settings

These are the default settings used when configuring your SRP for the first

time. See Getting Started with Device Configuration, page 12.

NOTE If you obtained your SRP from your Service Provider, you may not

have access to the Administrator account. If this is the case, please

contact your Service Provider for more information.

Getting to Know the Cisco SRP520-U Series

Services Ready Platforms

Model Numbers

Parameter Value

Device IP 192.168.15.1

Username admin

Password admin

DHCP Range 192.168.15.100 to 149

Model Description

SRP521W-U Fast Ethernet WAN

2 Phone (FXS) ports, 1 Line (FXO) port, 1 WAN (10/100) port,

4 LAN (10/100) ports, 1 USB 2.0 port, 802.11b/g/n, and WiFi

Protected Setup (WPS)

SRP526W-U ADSL2+ Annex B (ADSL over ISDN)

2 Phone (FXS) ports, 1 Line (FXO) port, 1 DSL port,

4 LAN (10/100) ports, 1 USB 2.0 port, 802.11b/g/n, and WiFi

Protected Setup (WPS)

SRP527W-U ADSL2+ Annex A/M (ADSL over POTS)

2 Phone (FXS) ports, 1 Line (FXO) port, 1 DSL port,

4 LAN (10/100) ports, 1 USB 2.0 port, 802.11b/g/n, and WiFi

Protected Setup (WPS)

4 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520-U Models)

Front Panel

SRP521W-U Front Panel

SRP526W-U and SRP527W-U Front Panel

Front Panel Lights

The following table describes the lights on the front panel of the SRP.

These lights are used for monitoring system activity.

Lights Description

POWER/SYS Solid green when the SRP has successfully booted and is

ready to use. Flashes green when the SRP is booting.

LAN ports (1–4) Solid green when a link is established. Flashes green when

there is activity on the LAN port.

WAN port

(SRP521W-U only)

Solid green when an Ethernet link is established. Flashes

green when there is activity on the WAN port.

Phone (FXS) ports

(1–2)

Solid green when the port is connected to a phone or fax

machine and the SRP is able to make and receive calls.

Flashes green when a call is in progress on the port.

DSL CD

(SRP526W-U/527W-U)

Flashes green when a DSL service is detected. Lights solid

green when synchronized.

Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520-U Models) 5

Back Panel

Network devices are connected to the back panel. The ports on the panel

vary depending on the model.

SRP521W-U Back Panel

DSL Data Flashes green when there is DSL activity on the line.

WLAN Solid green when the radio is powered on and operational.

Flashes green when there is wireless activity on the WLAN

port.

USB port Solid green when the connected USB device is operational.

Flashes green if there is a device failure or unsupported

device.

WPS Solid green when WiFi Protected Setup (WPS) is

operational.

A slow green flash indicates that the setup is in progress. A

fast green flash indicates a setup error.

276375

12VDC

LAN (10/100)WAN (10/100)

21 1234

LINE (FXO)PHONE (FXS)

WAN

Port

On/Off

Switch

12 V DC

power

Line

(FXO)

Port

Phone

(FXS)

Ports

LAN

Ports

6 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520-U Models)

SRP526W-U and SRP527W-U Back Panel

Back Panel Descriptions

Feature Description

DSL port

SRP526W-U/SRP527W-U only

Connect to a DSL connection.

Phone (FXS) ports (1–2) Connect directly to an analog telephone, fax machine,

or similar device.

If your analog phone requires a separate bell line, you

may need to connect a ring adapter between the SRP

and your phone so that the phone rings when calls are

presented.

Line (FXO) port Connect to an analog phone line.

WAN (10/100) port

SRP521W-U only

Connect to an Ethernet broadband Internet

connection.

LAN (10/100) ports (1–4) Connect to a wired computer and other network

devices.

Selectable WAN/LAN

(10/100) port

Port can be used as a WAN Ethernet port if the ADSL

interface is disabled. By default the ADSL port is

enabled, allowing this port to be used for LAN

connectivity. See the SRP500 Administration Guide

for further information.

On/Off Switch Powers the SRP on or off.

12V DC power Connect to the provided power adapter.

195211

LAN (10/100)LAN/WAN

21 1234

LINE (FXO)DSL PHONE (FXS)

On/Off

Switch

Line

(FXO)

Port

DSL

Port

Phone

(FXS)

Ports

LAN

Ports

12V DC

Power

Selectable

WAN/LAN

Port

Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520-U Models) 7

Side View

Feature Description

Reset button Press and hold for 5 seconds to reset the SRP. Press

and hold for 10 seconds to reset the SRP to its factory

defaults.

To press the button, insert a paper clip or similar

object into the opening.

CAUTION This will reset the device to its factory

default settings.

USB port Connect to a compatible USB Modem.

See Installing a Mobile Broadband USB Modem

(Optional), page 13.

WiFi Antenna Adjustable WiFi antenna.

276380

RESET

Reset

Button

USB

Connector

276381

WiFi Antenna

8 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520-U Models)

Top View

Installing the SRP500 Services Ready

Platforms

You can install the SRP on a desktop or other flat horizontal surface or

mount it on a wall.

The SRP has an adjustable WiFi antenna located on the side panel of the

unit. If used on a desktop, orient the antenna straight up. If wall mounted,

orient the antenna perpendicular to the floor.

Feature Description

WPS Button Use to automatically configure wireless security for devices

that support WiFi Protected Setup (WPS).

To configure WPS, press and hold this button until the WPS

light flashes. Make sure that the device is located near the

SRP during setup.

276378

WPS Button

Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520-U Models) 9

Placement Tips

Make sure that you install the SRP in a location that meets these

environmental conditions:

•StorageTemperature(sea level) -22° F to 140° F (-30° C to +60° C)

•OperatingTemperature(sea level) 32° F to 104° F (0° C to 40° C)

• Relative Humidity (sea level) 5 to 95% RH (non-condensing)

CAUTION Do not stack or place anything on top of the SRP, or install it on

a hot surface.

Desk Placement

To mount the SRP on a desktop, place the device on a flat surface so it sits

on its four rubber feet.

Wall Mounting

When mounting the SRP horizontally, position it so that the back panel

faces upward. This reduces strain on the cable connections. When

mounting it vertically, position the SRP so the USB ports face downward.

STEP 1Secure two number-six pan-head tapping screws, 3/4-inch (19 mm)

in length, 150 mm apart into a wall for horizontal orientation or

108 mm for vertical orientation, with the space between the

underside of each screw head and the surface of the wall equal to

5/32 inch (4mm).

CAUTION For drywall installation, secure the screws by using two

hollow-wall anchors (1/8 inch with 5/16-inch drill bit, or M3

with 8-mm drill bit). Without proper anchoring, the strain of

the network cable connections could pull the SRP from

the wall.

STEP 2Locate the mounting screw slots on the bottom of the SRP, and

then hang it on the screws.

10 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520-U Models)

Connecting the Equipment

STEP 1For Ethernet WAN connections, connect one end of the Ethernet

cable to your Internet access device (typically a modem), and

connect the other end of the cable to the WAN port.

For ADSL connections, connect your DSL cable directly to the DSL

port on your SRP526W-U or SRP527W-U. If required by your

Service Provider, make sure that you use an ADSL splitter.

SRP521W-U Ethernet WAN Connections

SRP526W-U / SRP527W-U ADSL Connections

STEP 2Connect wired computers and other network devices to the LAN

ports (1–4).

STEP 3(Optional) Connect an analog telephone, fax machine, or similar

device to the Phone (FXS) ports. Then connect the Line (FXO) ports

to the telephone line wall socket port(s).

STEP 4Connect the plug adaptor provided for your region to the power

supply. Only use the power adapter that was provided with the

unit.

STEP 5Connect the power adapter to the 12V DC port on your SRP.

195790

12VDC

LAN (10/100)WAN (10/100)

21 1234

LINE (FXO)PHONE (FXS)

WAN (10/100) Port

199989

LAN (10/100)LAN/WAN

21 1234

LINE (FXO)DSL PHONE (FXS)

DSL Port

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco 12000 GSR Series Service-Handbuch

Cisco

Cisco IAD2801 Series Bedienungsanleitung

Cisco

Cisco 2800 Series Referenzhandbuch

Cisco

Cisco RV180 Gebrauchs- und Pflegehandbuch

Cisco

Cisco GRS Bedienungsanleitung

Cisco

Cisco UBR7246VXR Handbuch

Cisco

Cisco 700 series Bedienungsanleitung

Cisco

Cisco 2500 Series Bedienerhandbuch

Cisco

Cisco BPX-8620 Bedienungs- und Wartungsanleitung

Cisco

Cisco Router Cisco 7206 VXR Bedienungsanleitung

Cisco

Cisco Linksys WET610N Bedienungsanleitung

Cisco

Cisco ASR-920-12SZ-IM Bedienungsanleitung

Cisco

Cisco 2501 - Router - EN Bedienungsanleitung

Cisco

Cisco Catalyst 8540 MSR Bedienungsanleitung

Cisco

Cisco 10008 Bedienerhandbuch

Cisco

Cisco aironet 1240 Handbuch

Cisco

Cisco IR8340 Kurzanleitung

Cisco

Cisco C11 1 8P Series Handbuch

Cisco

Cisco XR 12410 Bedienungsanleitung

Cisco

Cisco SGE2000 Bedienungsanleitung

Cisco

Cisco Catalyst 3550 Series Bedienungsanleitung

Cisco

Cisco 8100 Series Handbuch

Cisco

Cisco 7609 Bedienungsanleitung

Cisco

Cisco 1841 - 3G Bundle Router Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung