Cisco Meraki MV21 Bedienungsanleitung

MV21 Installation Guide

MV21 Overview

The Cisco Meraki MV21 is a networked camera that is exceptionally simple to deploy and configure due to its integration

into the Meraki dashboard and the use of cloud augmented edge storage. The MV family eliminates the complex and

costly servers and video recorders required by traditional solutions which removes the limitations typically placed on

video surveillance deployments.

ackage Contents

In addition to the MV camera, the following are provided:

Ethernet ort

The MV21 features a 100BASE-TX Ethernet port that supports 802.3af oE.

re-Install reparation

You should complete the following steps before going on-site to perform an installation.

Conﬁgure Your Network in Dashboard

The following is a brief overview only of the steps required to add an MV21 to your network. For detailed instructions

about creating, conﬁguring and managing Meraki Camera networks, refer to the online documentation

(https://documentation.meraki.com/MV).

1. Login to http://dashboard.meraki.com. If this is your ﬁrst time, create a new account.

2. Find the network to which you plan to add your cameras or create a new network.

3. Add your cameras to your network. You will need your Meraki order number (found on your invoice) or the serial

number of each camera, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit.

4. Verify that you the camera is now listed under Cameras > Monitor > Cameras.

Check and Conﬁgure Firewall Settings

If a ﬁrewall is in place, it must allow outgoing connections on particular ports to particular I addresses. The most

current list of outbound ports and I addresses for your particular organization can be found here.

DNS Configuration

Each MV21 will generate a unique domain name to allow for secured direct streaming functionality. These domain

names resolve an A record for the private ip address of the camera. Any public recursive DNS server will resolve this

domain.

If utilizing an on site DNS server, please whitelist *.devices.meraki.direct or configure a conditional forwarder so that

local domains are not appended to *.devices.meraki.direct and that these domain requests are forwarded to Google

public DNS.

Assigning I Addresses

At this time, the MV21 does not support static I assignment. MV21 units must be added to a subnet that uses DHC

and has available DHC addresses to operate correctly.

Installation Instructions

Note: Each MV21 comes with an instruction pamphlet within the box. This pamphlet contains detailed step by step

guides and images to assist in the physical install of the camera. A pdf of the pamphlet can be found here.

Note:During first time setup, the MV21 will automatically update to the latest stable firmware. Some features may be

unavailable until this automatic update is completed. This process may take up to 20 minutes due to enabling of whole

disk encryption.

Wall Mounting Instructions

For most mounting scenarios, the MV21 wall mount provides a quick, simple, and ﬂexible means of mounting your

device. The installation should be done in a few simple steps:

1. Leave protective plastic sticker on camera bubble

2. Use template to determine mounting hole locations before screwing in the mount plate. eel backing from mount

template to stick on wall. Slide the MV21 onto the wall mount.

3. Screw the mounting plate onto the wall in pre-determined locations. Use template holes marked with the letter “A” for

standard wall mounting.

4. Connect oE cable to camera. For cords that will exit the top of the camera, loop the cable inside the camera as

shown.

5. Slide camera over top of mount plate and slide down into mount plate hooks. Secure with hillips or Torx head safety

screw.

6. Turn bubble counter clockwise to unlock. Hinge bubble off of body to remove.

7. inch near thumb screws and pull straight away from the camera to remove lens guard.

8. Aim the lens. Look through the camera on the Meraki Dashboard to fine tune the picture. The camera sensor and

lens unit can be physically tilted through a range of 65 degrees, rotated through a range of 350 degrees, and panned

through a range of 350 degrees. The image can only be rotated by 180 degrees in software and no other adjustments

can be made. Zoom and focus can be adjusted remotely and can not be adjusted physically on the camera.

9. Replace lens guard and bubble. Turn bubble clockwise to lock.

10. Remove protective plastic sticker. Check LED function. Use the Meraki Dashboard to adjust camera focus and

configure other settings.

T-rail Mounting Instructions

To mount your MV21 on a drop ceiling T-rail, use the included hardware. The hardware can be used to mount to most 9/

16”, 15/16”, or 1 ½” T-rails.

1. Using the dashed lines on the mount plate template as a guide, set the proper spacing of the clips.

2. Tighten the set screws on the T-rail clips and secure them using a 5/64” (2 mm) hex key.

3. Attach the mount plate to the T-rail clips using the mount plate holes (marked with a “G”).

4. Attach the T-rail clips to the T-rail by rotating them and snapping them into place as shown. The black foam pads

should be compressed slightly after installation.

owering the MV21

Remove the cable guard and route the Ethernet cable from an active port on a 802.3af oE switch or oE injector.

Note: Power over Ethernet supports a maximum cable length of 300 ft (100 m).

LED Indicator

Your MV21 is equipped with a LED light on the front of the unit to convey information about system functionality and

performance:

• Flashing Green (2 second interval) - MV is upgrading or initializing for the first time.

• Solid Green - MV is operating nominally.

Inhaltsverzeichnis

Andere Cisco Sicherheitskamera Handbücher

Cisco

Cisco PVC2300 - Small Business Internet Video... Bedienungsanleitung

Cisco

Cisco 6020 Bedienungs- und Sicherheitshinweise

Cisco

Cisco 3421V Bedienungsanleitung

Cisco

Cisco Wireless Service Module 2 Bedienungsanleitung

Cisco

Cisco CIVS-IPC-2911 Bedienungsanleitung

Cisco

Cisco Small Business VC240 Bedienungsanleitung

Cisco

Cisco WVC210 - Small Business Wireless-G PTZ Internet Video... Bedienungsanleitung

Cisco

Cisco Small Business VC220 Bedienungsanleitung

Cisco

Cisco 3630 Bedienungsanleitung

Cisco

Cisco 253 Series Bedienungsanleitung

Cisco

Cisco Meraki MV93 Series Bedienungsanleitung

Cisco

Cisco 3530 Bedienungsanleitung

Cisco

Cisco WVC210 - Small Business Wireless-G PTZ Internet Video... Bedienungsanleitung

Cisco

Cisco CIVS-IPC-2521V Bedienungsanleitung

Cisco

Cisco 4300E Bedienungsanleitung

Cisco

Cisco WVC210 - Small Business Wireless-G PTZ Internet Video... Bedienungsanleitung

Cisco

Cisco WVC210 - Small Business Wireless-G PTZ Internet Video... Bedienungsanleitung

Cisco

Cisco WVC80N Bedienungsanleitung

Cisco

Cisco 7030E Bedienungsanleitung

Cisco

Cisco Meraki MV12 Bedienungsanleitung

Cisco

Cisco Small Business VC240 Bedienungsanleitung

Cisco

Cisco TelePresence MX700 Bedienungsanleitung

Cisco

Cisco Nexus 5010 Bedienungsanleitung

Cisco

Cisco 6020 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung