Cisco ISA 3000 Bedienungsanleitung

Product Overview

This chapter provides an overview of the features available for the Cisco ISA 3000

•General Description, on page 1

•Hardware Features, on page 7

•Alarm Ports, on page 11

•Power Supply, on page 11

•Temperature Sensor, on page 12

General Description

The Cisco ISA 3000 is a DIN Rail mounted ruggedized industrial security appliance that provides firewall,

threat defense, and VPN services. The term DIN Rail describes a metal rail of a standard type widely used

for mounting circuit breakers and industrial control equipment inside equipment racks. The term derives from

the original specifications published by Deutsches Institut für Normung (DIN) in Germany. The device can

run either the ASA or Firepower Threat Defense operating system.

The Cisco ISA 3000 is low-power, fan-less, with Gigabit Ethernet and a dedicated management port. There

are two SKUs:

• ISA3000-4C-K9 — Copper SKU with 4x10/100/1000Base-T with a management port.

• ISA3000-2C2F-K9 — Fiber SKU with 2x1GbE SFP and 2x10/100/1000Base-T with a management

port.

The following figures show the front panel details of the two SKUs

Product Overview

Figure 1: Cisco ISA 3000 Copper SKU

The following figure describes the front panel features:

Product Overview

General Description

Figure 2: Cisco ISA 3000 Fiber SKU

Product Overview

General Description

Figure 3: Cisco ISA 3000 Front Panel

DescriptionPINDescriptionPIN

RJ45 10/100/100 BaseT

Connectors 1&2

10Reset Pinhole Access1

On the ISA-3000-2C2F SKU,

these are the SFP sockets.

On the ISA-3000-4C SKU,

these are RJ45 10/100/100

BaseT Connectors 3&4

11Console LED2

1GB removable SD flash

memory card slot

12System LED3

Alarm Connectors13Console connector (RJ-45)4

Grounding Point14Console connector (mini-USB)5

Alarm LEDs15USB connectors6

Product Overview

General Description

DescriptionPINDescriptionPIN

DC Power LEDs16Management Interface7

Gigabit Ethernet LEDs17DC power connection A8

Management LED18DC power connection B9

ISA 3000 Shutdown

There is a new graceful shutdown option supported for Firepower Threat Defense as of 7.0.2/7.2. There is

also an LED change new for 7.0.5/7.3. Use shutdown when you intend to remove the device from the network,

for example to replace it, or for any scheduled maintenance.

There is no change to procedures with ASA.

It is recommended to wait for10 seconds after the System LED is switched OFF to unplug the power

from the device.

Note

After shutting down the device, you can turn it back on only by Power cycling the device. There is no hardware

On/Off switch for the device on the chassis. Power up the device to restart the device again.

LEDs

The following table describes the LEDs for the Cisco ISA 3000.

Table 1: LED Descriptions

DescriptionActivityLED

Off — No power

Green Steady on — Normal operation

Green Flashing — Boot up phase

Red Flashing — BIOS and POST

Red — System is not functioning properly.

Power StatusSystem

Off — No link (default)

Green Steady on — Port link with no activity

Green Flashing — Transmitting and Receiving data

Management Port StatusMGMT

Off — Power is not present

Green Steady on — Power is present on the associated circuit. (Hardware controlled)

Red Steady on — Power is not present on the associated circuit, and the system is

configured for dual-input power

DC Power StatusDC_A

DC_B

Product Overview

ISA 3000 Shutdown

DescriptionActivityLED

Off — Alarm Out not configured or the system is off (Default)

Green Steady on — Alarm Out is configured, no alarm detected.

Red Steady on — Minor alarm detected

Red Flashing — Major alarm detected

Alarm monitoringAlarm Out

Off — Alarm In not configured or the system is off (Default)

Green Steady on — Alarm In is configured, no alarm detected.

Red Steady on — Minor alarm detected

Red Flashing — Major alarm detected

Alarm monitoringAlarm In

1&2

Off — No link

Green Steady on — Link is up

Green Flashing — Transmitting and Receiving data

Amber — Fault, check log

Port 1&2 and in the copper SKU, 3&4 LEDs fast blink amber together — Those two ports

are in bypass mode.

Link StatusEthernet

Ports

Off — RJ-45 is being used for console

Green — Mini USB is being used for console

Console connection

Status

Console

Memory and Storage

The Cisco ISA 3000 has the following:

• 8-GB DRAM (soldered down).

• 16-GB onboard flash memory

• 64-GB mSATA solid state drive (SSD)

• 1-GB removable SD flash memory card - industrial temp

USB Ports

The Cisco ISA 3000 has two externally accessible Type-A USB (4-pin) connectors. Each USB port will

support output powering of 5 volts and up to a maximum of 500 mA.

Management Ethernet Port

A management-only 10/100/1000 BaseT Ethernet port is provided. This port will be the only port able to be

used for booting over the network, or for initial setup and management of the system. This port is Management

1/1 in the configuration.

Product Overview

Memory and Storage

Console Port

The Cisco ISA 3000 can be configured through a web interface, or through the console port. The console port

is either a RJ45 or a Mini USB connector. A standard management cable (Part number 72-3383-01) can be

used to convert the RJ45 to DB9 connector.

The default configuration settings for the RJ45 console port are:

• 9600 baud, 8 data bits, no parity, 1 stop bit, no flow control.

• If the USB Console Port is active (cable inserted and remote PC drivers are enabled) by default the

console will switch from RJ45 to USB when the USB cable is detected. If both ports are connected, the

Mini USB console port is used.

If your laptop or PC warns you that you do not have the proper drivers to communicate with the device, you

can obtain them from your computers manufacturer, or go here:

https://software.cisco.com/download/home/282774227/type/282855122/release/3.1

The following table shows the pin-outs for the CON/AUX RJ-45 connector:

Table 2: RJ-45 Pinouts

DirectionSignalPin

OutputDTR1

Output3.32

OutputTXD3

-GND4

-GND5

InputRXD6

NC-7

NC-8

The console port will not support a remote dial-in modem.

Note

Hardware Features

This section provides an overview of the following hardware features for the Cisco ISA 3000.

Platform Features for the Cisco ISA 3000

The following lists the hardware platform features.

Product Overview

Console Port

• CPU Intel 4 Core 1.25Ghz

• 8 GB of 1333MHz DDR3 Memory

• Dedicated management-only Gigabit Ethernet port

• Mini-USB and RJ45 Console port

• +/- 12 to 48VDC Rated (9.6 to 60VDC Maximum) redundant power connectors with 24-12 AWG screw

cage terminals

• Two external USB-A ports for addition of memory cards, security tokens, modems, or other USB 2.0

compliant devices

• DIN Rail mount incorporated into the chassis

• Fan-less design

• Fault relay outputs and 2 alarm inputs

• Industrial temperature SDHC card support

• Redundant power inputs

• Secure boot support

• Bypass Relay (only available on copper ports)

Reset Button

The Reset button resets the security appliance configuration to the default configuration set by the factory.

To restore the security appliance configuration to the default configuration set by the factory, use a standard

size #1 paper clip with wire gauge 0.033 inch or smaller and simultaneously press the reset button while

applying power to the security appliance.

When depressed the push-button follows these actions:

• Depressed 0 to < 3 seconds or > 15 seconds — No action is taken.

• Depressed > 3 seconds < 15 seconds — ASA: After reboot, the unit will be running the original factory

default configuration, including ROMMON variables.

• Depressed > 3 seconds < 15 seconds — FTD (7.0+) using Firepower Management Center: If you have

a backup configuration on an SD card, a zero-touch restore is initiated.

Power Supply

The Cisco ISA 3000 comes with redundant external power connector. the connector supports 12 - 48 VDC.

The connectors are Molex 5.00mm Pitch Eurostyle™Horizontal Plug, with Retention Screws.

The power supply does not support reverse polarity, but does have reverse polarity protection. This means if

you reverse + & - connections, the system will not power on but there will be no damage.

The + terminal always has to be greater than the - terminal for the system to operate. The difference is in the

system grounding scheme used.

The ISA 3000 supports 3 basic schemes:

Product Overview

Reset Button

• Isolated DC in, neither + nor - terminal is tied to chassis GND

• Positive DC in, negative (-) terminal is tied to chassis GND

• Negative DC in, positive (+) terminal is tied to chassis GND

To ensure uninterrupted operation the redundant power connections must be connected to independently

separated power sources.

Note

1GB Removable SD Flash Memory Card

The Cisco ISA 3000 has a removable SD flash memory slot (referred to as SD). This is primarily to allow

easy updates, copying of logs and crash-dumps. The device does not come with a removable SD flash memory

card installed, this is an optional spare item, Cisco part number SD-IE-1GB=. Contact your Cisco Marketing

Representative for ordering information.

Check the software guide for the operating system you are running for information on SD memory

support.

Note

Installing or Removing the SD Card (Optional)

Do not insert or remove the SD card while power is on; an electrical arc can occur. This could cause an

explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous

before proceeding. Statement 379

Warning

The SD card is hidden under a protective cover:

Product Overview

1GB Removable SD Flash Memory Card

Figure 4: SD Card Cover

Phillips screw1

Door pivot point2

For hazardous locations environments, if you are installing or removing the flash card or alarm wiring, follow

these warnings:

When you connect or disconnect the power and/or alarm connector with power applied, an electrical

arc can occur. This could cause an explosion in hazardous area installations. Be sure that all power is

removed from the device and any other circuits. Be sure that power cannot be accidentally turned on or

verify that the area is nonhazardous before proceeding. Statement 1058

Warning

Do not insert or remove the flash card while power is on; an electrical arc can occur. This could cause

an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous

before proceeding. Statement 379

Warning

Product Overview

Installing or Removing the SD Card (Optional)

Andere Handbücher für ISA 3000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Sicherheitssystem Handbücher

Cisco

Cisco Firepower 2100 Series Handbuch

Cisco

Cisco Firepower 2100 Series Handbuch

Cisco

Cisco NCS 4000 Series Bedienungsanleitung

Cisco

Cisco 4116 - EtherFast Switch Leitfaden

Cisco

Cisco Telepresence MX200 Bedienungsanleitung

Cisco

Cisco IronPort S670 Bedienungsanleitung

Cisco

Cisco Small Business Pro SA 500 Series Bedienungsanleitung

Cisco

Cisco 6400E Bedienungsanleitung

Cisco

Cisco PIX-515-RPS - PIX 515-R - Firewall Bedienungsanleitung

Cisco

Cisco ISA 3000 Bedienerhandbuch

Cisco

Cisco WVC200 - Wireless-G PTZ Internet Camera Bedienungsanleitung

Cisco

Cisco PIX 525 Bedienungsanleitung

Cisco

Cisco Firepower 1100 Series Bedienungsanleitung

Cisco

Cisco PIX 501 - Security Appliance Bedienungsanleitung

Cisco

Cisco ASA 5506W-X Handbuch

Cisco

Cisco 500 Series Bedienungsanleitung

Cisco

Cisco M5 Bedienungsanleitung

Cisco

Cisco MARS Gebrauchsanweisung

Cisco

Cisco MS410-16 Bedienungsanleitung

Cisco

Cisco MEDVIEW-C-30XS-A01 Bedienungsanleitung

Cisco

Cisco ISA550 Bedienungsanleitung

Cisco

Cisco ISA550 Bedienungsanleitung

Cisco

Cisco C195 Kurzanleitung

Cisco

Cisco ASA 55 Series Kurzanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung