Cisco 3500 Series Bedienungsanleitung

Cisco Secure Network Server 3500 Series Appliance Hardware

Installation Guide

First Published: 2016-10-10

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network

topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional

and coincidental.

All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.

Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:

https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a

partnership relationship between Cisco and any other company. (1721R)

CONTENTS

Cisco SNS 3500 Series Appliance Overview 1

CHAPTER 1

Cisco SNS 3500 Series Appliances 1

LED Indicators on Cisco SNS 3515 and 3595 Appliances 1

Cisco SNS-3515 and SNS-3595 Appliances Hardware Specifications 1

Cisco SNS-3515 or 3595 Appliance Front Panel View 2

Cisco SNS 3515 or SNS 3595 Appliance Back Panel View 5

Internal Diagnostic LEDs 7

Regulatory Compliance 8

Before You Begin 9

CHAPTER 2

Safety Guidelines 9

Unpack and Inspect the Server 10

Prepare for Server Installation 11

Installation Guidelines 12

Rack Requirements 12

Equipment Requirements 13

Slide Rail Adjustment Range 13

Server Specifications 13

Physical Specifications 13

Environmental Specifications 13

Power Specifications 14

Install the Cisco SNS 3515 and Cisco SNS 3595 Hardware Appliances 15

CHAPTER 3

Install the Cisco SNS 3515 and Cisco SNS 3595 Hardware Appliances 15

Install the Cisco SNS 3515 or 3595 Appliance in a Rack 15

Install the Side Rails 16

Cisco Secure Network Server 3500 Series Appliance Hardware Installation Guide

iii

Install the Cable Management Arm (Optional) 18

Reverse the Cable Management Arm (Optional) 19

Connect Cables 20

Connect the Network Interface 20

Connect the Console 22

Connect the Keyboard and Video Monitor 22

Cable Management 23

Connect and Power On the Cisco SNS 3515 or 3595 Appliance 23

Connect and Power On the Server (Standalone Mode) 23

Cisco Integrated Management Controller 25

Setup CIMC Configuration Utility 26

NIC Modes and NIC Redundancy Settings 28

Upgrade the BIOS and Cisco IMC Firmware 29

Access the System BIOS 30

Cisco Secure Network Server 3500 Series Appliance Hardware Installation Guide

Contents

CHAPTER 1

Cisco SNS 3500 Series Appliance Overview

•Cisco SNS 3500 Series Appliances, on page 1

Cisco SNS 3500 Series Appliances

The Cisco SNS 3515 or Cisco SNS 3595 appliance is designed for performance and density over a wide range

of business workloads, from web serving to distributed databases.

The SNS 3515 and SNS 3595 appliances support only Cisco ISE 2.0.1 or later releases. You cannot install a

release earlier than 2.0.1 on the SNS 3515 or SNS 3595 appliance.

Note

Support for UEFI Secure Boot

The SNS 3515 and SNS 3595 appliances support the Unified Extensible Firmware Interface (UEFI) secure

boot feature. This feature ensures that only a Cisco-signed ISE image can be installed on the SNS 3515 and

SNS 3595 appliances, and prevents installation of any unsigned operating system even with physical access

to the device. For example, generic operating systems, such as Red Hat Enterprise Linux or Microsoft Windows

cannot boot on this appliance.

LED Indicators on Cisco SNS 3515 and 3595 Appliances

This section describes the front- and rear-panel controls, ports, and LED indicators on the Cisco SNS 3515

and Cisco SNS 3595 appliances.

Cisco SNS-3515 and SNS-3595 Appliances Hardware Specifications

The following table describes the hardware specifications of Cisco SNS-3515 and Cisco SNS-3595 appliances.

Cisco Secure Network Server 3500 Series Appliance Hardware Installation Guide

DiagramsHardware SpecificationsCisco Identity Services

Engine Appliance

Cisco SNS-3515 or 3595 Appliance

Front Panel View, on page 2

Cisco SNS 3515 or SNS 3595

Appliance Back Panel View, on

page 5

• Cisco UCS C220 M4

• Single socket Intel Xeon E5-2620

v3 series CPU @ 2.40GHz, 12 total

cores, 6*2 total threads

• 16 GB RAM

• 1 x 600-GB disk

• 6 GbE network interfaces

• For physical, environmental, and

power specifications, see Server

Specifications, on page 13

Cisco SNS-3515-K9

• Cisco UCS C220 M4

• Dual socket Intel Xeon E5-2640 v3

series CPU @ 2.60GHz, 16 total

cores, 8*2 total threads

64 GB RAM

4 x 600-GB disks

RAID 10

6 GbE network interfaces

For physical, environmental, and

power specifications, see Server

Specifications, on page 13.

Cisco SNS-3595-K9

You cannot add additional hardware resources like memory, processor, or hard disk to a Cisco SNS 3500

series appliance.

Note

Cisco SNS-3515 or 3595 Appliance Front Panel View

The following figure shows the components of the Cisco SNS-3515 or Cisco SNS-3595 appliance front panel

view.

Cisco Secure Network Server 3500 Series Appliance Hardware Installation Guide

Cisco SNS 3500 Series Appliance Overview

Cisco SNS-3515 or 3595 Appliance Front Panel View

Figure 1: Front Panel LEDs

System status LED7Drive bays 1-8 support SAS/SATA drives1

Fan status LED8Drive bays 1 and 2 support SAS/SATA

and NVMe PCIe solid state drives (SSDs)

Temperature status LED9Pull-out asset tag3

Power supply status LED10Operations panel buttons and LEDs4

Network link activity LED11Power button/power status LED5

KVM connector (used with KVM cable that

provides two USB 2.0, one VGA, and one

serial connector)

12Unit identification button/LED6

The following table describes the LEDs located on the front panel of the Cisco SNS-3515 or Cisco SNS-3595

appliance.

Front Panel LEDs

• Off—The hard drive is operating properly.

• Amber—Drive fault detected.

• Amber, blinking—The device is rebuilding.

• Amber, blinking with one-second

interval—Drive locate function activated.

Hard drive fault

Cisco Secure Network Server 3500 Series Appliance Hardware Installation Guide

Cisco SNS 3500 Series Appliance Overview

Cisco SNS-3515 or 3595 Appliance Front Panel View

Front Panel LEDs

• Off—There is no hard drive in the hard drive

tray (no access, no fault).

• Green—The hard drive is ready.

• Green, blinking—The hard drive is reading or

writing data.

Hard drive activity

• Off—There is no AC power to the server.

• Amber—The server is in standby power mode.

Power is supplied only to the Cisco IMC and

some motherboard functions.

• Green—The server is in main power mode.

Power is supplied to all server components.

Power button/LED

• Off—The unit identification function is not in

use.

• Blue—The unit identification function is

activated.

Unit identification

• Green—The server is running in normal

operating condition.

• Green, blinking—The server is performing

system initialization and memory check.

• Amber, steady—The server is in a degraded

operational state. For example:

• Power supply redundancy is lost.

• CPUs are mismatched.

• At least one CPU is faulty.

• At least one DIMM is faulty.

• At least one drive in a RAID configuration

failed.

•Amber, blinking—The server is in a critical fault

state. For example:

• Boot failed.

• Fatal CPU and/or bus error is detected.

• Server is in an over-temperature condition.

System status

• Green—All fan modules are operating properly.

• Amber, steady—One or more fan modules

breached the critical threshold.

• Amber, blinking—One or more fan modules

breached the non-recoverable threshold.

Fan status

Cisco Secure Network Server 3500 Series Appliance Hardware Installation Guide

Cisco SNS 3500 Series Appliance Overview

Cisco SNS-3515 or 3595 Appliance Front Panel View

Front Panel LEDs

• Green—The server is operating at normal

temperature.

• Amber, steady—One or more temperature

sensors breached the critical threshold.

• Amber, blinking—One or more temperature

sensors breached the non-recoverable threshold.

Temperature status

• Green—All power supplies are operating

normally.

•Amber, steady—One or more power supplies are

in a degraded operational state.

• Amber, blinking—One or more power supplies

are in a critical fault state.

Power supply status

• Off—The Ethernet link is idle.

• Green—One or more Ethernet LOM ports are

link-active, but there is no activity.

• Green, blinking—One or more Ethernet LOM

ports are link-active, with activity.

Network link activity

Cisco SNS 3515 or SNS 3595 Appliance Back Panel View

The following figure shows the components of the Cisco SNS-3515 and Cisco 3595 appliance back panel

view.

Figure 2: Back Panel LEDs

1-GbE Ethernet dedicated management port;

used to access CIMC

9Grounding-lug hole (for DC power

supplies)

Serial port (RJ-45 connector)10PCIe riser 1/slot 12

1-GbE Ethernet port (Eth 0)11PCIe riser 2/slot 23

1-GbE Ethernet port (Eth 1)121-GbE Ethernet port (Eth 2)4

VGA video port (DB-15)131-GbE Ethernet port (Eth 3)5

Rear unit identification button/LED141-GbE Ethernet port (Eth 4)6

Cisco Secure Network Server 3500 Series Appliance Hardware Installation Guide

Cisco SNS 3500 Series Appliance Overview

Cisco SNS 3515 or SNS 3595 Appliance Back Panel View

Power supplies (up to two, redundant as

1+1)

151-GbE Ethernet port (Eth 5)7

USB 3.0 ports (two)8

The following table describes the LEDs located on the back panel of the Cisco SNS 3515 or Cisco SNS 3595

appliance.

StateLED Name

• Off—No link is present.

• Green, steady—Link is active.

• Green, blinking—Traffic is present on the active

link.

Optional mLOM 1-GbE SFP+ (there is a single status

LED)

• Off—Link speed is 10 Mbps.

• Amber—Link speed is 100 Mbps/1 Gbps.

• Green—Link speed is 10 Gbps.

Optional mLOM 1-GbE BASE-T link speed

• Off—No link is present.

• Green—Link is active.

• Green, blinking—Traffic is present on the active

link.

Optional mLOM 1-GbE BASE-T link status

• Off—Link speed is 10 Mbps.

• Amber—Link speed is 100 Mbps.

• Green—Link speed is 1 Gbps.

1-GbE Ethernet dedicated management link speed

• Off—No link is present.

• Green—Link is active.

• Green, blinking—Traffic is present on the active

link.

1-GbE Ethernet dedicated management link status

• Off—Link speed is 10 Mbps.

• Amber—Link speed is 100 Mbps.

• Green—Link speed is 1 Gbps.

1-GbE Ethernet link speed

• Off—No link is present.

• Green—Link is active.

• Green, blinking—Traffic is present on the active

link.

1-GbE Ethernet link status

• Off—The unit identification LED is not in use.

• Blue—The unit identification LED is activated.

Rear unit identification

Cisco Secure Network Server 3500 Series Appliance Hardware Installation Guide

Cisco SNS 3500 Series Appliance Overview

Cisco SNS 3515 or SNS 3595 Appliance Back Panel View

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco 5100 Bedienungsanleitung

Cisco

Cisco UCS M3 Series Bedienungsanleitung

Cisco

Cisco Content Delivery Engine CDE100 Handbuch

Cisco

Cisco UCS C240 M3 Kurzanleitung

Cisco

Cisco UCS C220 M3 Bedienungsanleitung

Cisco

Cisco TelePresence Server 7010 Technisches Datenblatt

Cisco

Cisco N20-B6625-1 Systemhandbuch

Cisco

Cisco UCS C210 M2 Systemhandbuch

Cisco

Cisco TelePresence Video Communication Server Service-Handbuch

Cisco

Cisco UCS B420 M4 Bedienungsanleitung

Cisco

Cisco UCS 5108 Bedienungsanleitung

Cisco

Cisco UCS C240 Montage- und Wartungsanleitung

Cisco

Cisco TelePresence Video Communication Server... Bedienungsanleitung

Cisco

Cisco UCS B Series Installations- und Betriebshandbuch

Cisco

Cisco TelePresence Service-Handbuch

Cisco

Cisco Catalyst 6800 Bedienungsanleitung

Cisco

Cisco UCS C460 Montage- und Wartungsanleitung

Cisco

Cisco Digital Media System 3.5 Bedienungsanleitung

Cisco

Cisco TelePresence Bedienungsanleitung

Cisco

Cisco Secure Network Server 3600 Series Handbuch

Cisco

Cisco UCS C240 M3 Bedienungsanleitung

Cisco

Cisco UCS 82598KR Bedienungsanleitung

Cisco

Cisco SNS-3415 series Bedienungsanleitung

Cisco

Cisco UCS B420 M4 Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung