Cisco Firepower Management Centers Bedienungsanleitung

A-1

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

APPENDIX

Memory Upgrade Instructions for Firepower

Management Centers

This section describes how to replace the memory modules that are located internally within your Cisco

Firepower Management Center. You need to remove the cover from the appliance to replace these items.

The document contains the following sections:

•Memory Upgrade Overview, page A-1

•Working in an ESD Environment, page A-2

•Safety Warnings, page A-2

•Removing the Chassis Cover, page A-3

•Removing the Processor Air Duct, page A-6

•Replacing the DIMMs, page A-9

•Installing the Processor Air Duct, page A-14

•Installing the Chassis Cover, page A-18

Memory Upgrade Overview

As additional software feature enhancements are introduced the minimum memory requirements are

changing for the Firepower Management Centers MC750 (Rev. 1 or Rev. 2), MC1500, and MC3500

models. Appliances that do not meet the minimum memory requirement are not supported.

Table A-1 outlines the RAM upgrade requirements.

Table A-1 Overview of RAM Upgrade Requirements

Management Center

Model

Default Shipping RAM

(prior to December 2014)

DIMM

Locations

New RAM Requirements

(after December 2014)

MC750 (Rev. 1) 4GB (1 4GB module) A1 8GB (2 4GB modules)

MC750 (Rev. 2) 4GB (1 4GB module) A1 8GB (2 4GB modules)

MC1500 12 GB (3 x 4GB modules) A1, B1, and C1 48 GB (3 x 16GB modules)

MC3500 12 GB (3 x 4GB modules) A1, B1, and C1 48 GB (3 x 16GB modules)

A-2

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

Appendix A Memory Upgrade Instructions for Firepower Management Centers

Working in an ESD Environment

Upgraded Default RAM in Shipping Firepower 7000 and 8000 Series

Management Centers

All Firepower MC750, MC1500, and MC3500 Management Centers will ship with additional default

memory to meet the memory requirements beginning in December 2014.

Note Firepower MC1500 and MC3500 Management Centers already deployed prior to December 2014 should

function as intended with the default 12 GB of installed RAM. Contact Cisco regarding RAM upgrade

options for your particular deployment if you encounter performance issues.

Upgrade Paths for Existing Firepower Management Centers

Table A-2 lists the memory upgrade kits that will enable customers to upgrade their existing Firepower

Management Centers in order to deploy the latest software release.

Caution Yo u must remove all installed DIMMs and replace them with the modules from the upgrade kit.

Working in an ESD Environment

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs

when electronic components are improperly handled and can result in complete or intermittent failures.

Always follow ESD-prevention procedures when you remove and replace components. Ensure that the

chassis is electrically connected to earth ground. Wear an ESD-preventive wrist strap, ensuring that it

makes good skin contact. Connect the grounding clip to an unpainted surface of the chassis frame to

safely ground unwanted ESD voltages. To guard against ESD damage and shocks, the wrist strap and

cord must operate properly. If no wrist strap is available, ground yourself by touching the metal part of

the chassis.

Caution For the safety of your equipment, periodically check the resistance value of the anti-static strap. It should

be between 1 and 10 megohms (Mohm).

Safety Warnings

This section contains important safety warnings for the installation and use of the appliance.

Table A-2 Memory Upgrade Kits for Firepower Management Centers

Memory Kits Applicable Management Center Models

FS750-MEM-KIT= MC750 (Rev. 1)

MC750 (Rev. 2)

FS3500-MEM-KIT=

FS3500-MEM-U=

MC1500

MC3500

A-3

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

Appendix A Memory Upgrade Instructions for Firepower Management Centers

Removing the Chassis Cover

Warning

Before working on a system that has an On/Off switch, turn OFF the power and unplug the power

cord. Statement 1

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this

equipment. Statement 1030

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment

in the absence of a suitably installed ground conductor. Contact the appropriate electrical

inspection authority or an electrician if you are uncertain that suitable grounding is available.

Statement 1024

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning

Read the installation instructions before connecting the system to the power source. Statement

1004

Warning

Ultimate disposal of this product should be handled according to all national laws and

regulations. Statement 1040

Removing the Chassis Cover

Firepower Management Centers have covers that slide off the rear of the chassis. There are slight

differences between chassis models which are described in the following sections:

•Removing the Cover from Firepower Management Center 750, page A-3

•Removing the Cover from Firepower Management Center 1500 and 3500, page A-5

Removing the Cover from Firepower Management Center 750

The procedure for removing the cover from a Firepower Management Center 750 differs depending on

the revision of the appliance (Rev. 1 or Rev. 2). See Figure A-1 for an illustration of the MC750 Rev. 1

chassis. See Figure A-2 for an illustration of the MC750 Rev. 2 chassis.

To remove the cover from a Firepower MC750:

Note A nonskid surface or a stop behind the MC750 (Rev. 1 or Rev. 2) may be needed to prevent the device

from sliding on your work surface.

A-4

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

Appendix A Memory Upgrade Instructions for Firepower Management Centers

Removing the Chassis Cover

Step 1 Observe the ESD precautions described in Working in an ESD Environment, page A-2 and the safety

precautions described in Safety Warnings, page A-2.

Step 2 Remove the security screws from the front of the chassis:

•For Rev. 1, there are two (2) screws (see “1” in Figure A-1).

•For Rev. 2, there are three (3) screws (see “1” in Figure A-2).

Step 3 Remove the security screw from the rear of the chassis. See “2” in Figure A-1 and Figure A-2.

Step 4 Slide the cover towards the rear by pushing on the blue grip points on the chassis cover:

•For Rev. 1, there is one (1) grip point (see “3” in Figure A-1).

•For Rev. 2, there are two (2) grip points (see “3” in Figure A-2).

Step 5 Lift the over off and set aside.

What to Do Next:

•Remove the processor air duct as described in the “Removing the Processor Air Duct from

Firepower Management Center 750” section on page A-6.

Figure A-1 Removing the Cover from a MC750 Rev. 1

1Front security screws 3Rubber grip point

2Rear security screw 4Top cover

A-5

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

Appendix A Memory Upgrade Instructions for Firepower Management Centers

Removing the Chassis Cover

Figure A-2 Removing the Cover from a MC750 Rev. 2

Removing the Cover from Firepower Management Center 1500 and 3500

The MC1500 and MC3500 Management Centers share some of the same form factors. The following

procedure can apply to either device.

To remove the cover from a Firepower MC1500 or MC3500:

Note A nonskid surface or a stop behind the MC1500 or MC3500 may be needed to prevent the device from

sliding on your work surface.

Step 1 Observe the ESD precautions described in Working in an ESD Environment, page A-2 and the safety

precautions described in <Blue>Safety Warnings on page 2.

Step 2 Remove the security screw if it is installed (see “1” in Figure A-3).

Step 3 Cut the warranty label on the unit if it is intact.

Step 4 While holding in the blue button on the top of the chassis (see “3” in Figure A-3), slide the top cover

back until it stops (see “4” in Figure A-3).

•On the MC1500, the button is on the left.

•On the MC3500, the button is on the right as shown in Figure A-3.

Step 5 Insert your finger in the notch (see “2” in Figure A-3) and lift the cover upward to remove it.

What to Do Next:

•Remove the processor air duct as described in the “Removing the Processor Air Duct from

Firepower Management Center 1500 and 3500” section on page A-8.

1Front security screws 3Rubber grip points

2Rear security screw 4Top cover

364268

A-6

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

Appendix A Memory Upgrade Instructions for Firepower Management Centers

Removing the Processor Air Duct

Figure A-3 Removing the Cover from a MC1500 or MC3500

Removing the Processor Air Duct

Firepower Management Centers operate with processor air ducts in place. The air ducts are required for

proper airflow within the chassis. It is necessary to remove the air ducts to gain full access to the DIMM

sockets on the chassis. There are some differences between chassis models which are described in the

following sections:

•Removing the Processor Air Duct from Firepower Management Center 750, page A-6

•Removing the Processor Air Duct from Firepower Management Center 1500 and 3500, page A-8

Removing the Processor Air Duct from Firepower Management Center

750

The procedure for removing the air duct from a Firepower MC750 differs depending on the revision of

the appliance (Rev. 1 or Rev. 2). See Figure A-4 for an illustration of the MC750 Rev. 1 chassis. See

Figure A-5 for an illustration of the MC750 Rev. 2 chassis.

To remove the processor air duct from a Firepower MC750:

Step 1 Observe the ESD precautions described in Working in an ESD Environment, page A-2 and the safety

precautions described in Safety Warnings, page A-2.

Step 2 Lift the processor air duct from its location behind the system cooling fans:

•For Rev. 1 chassis see “1” in Figure A-4)

•For Rev. 2 chassis see “1” in Figure A-5).

Step 3 Set the air duct aside.

1Security screw 3Top cover

2Button 4Notch

364169

A-7

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

Appendix A Memory Upgrade Instructions for Firepower Management Centers

Removing the Processor Air Duct

What to Do Next:

•Remove the Firepower MC750 DIMMs as described in the “Replacing the DIMMs” section on

page A-9.

Figure A-4 Removing the Processor Air Duct from a MC750 Rev. 1

Figure A-5 Removing the Processor Air Duct from a MC750 Rev. 2

1Processor air duct ——

A-8

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

Appendix A Memory Upgrade Instructions for Firepower Management Centers

Removing the Processor Air Duct

Removing the Processor Air Duct from Firepower Management Center

1500 and 3500

The Firepower MC1500 and MC3500 share some of the same form factors. The following procedure can

apply to either device.

Note Before the processor air duct can be removed from a MC1500 and MC3500, the adjacent PCI Riser

Assembly must first be removed.

To remove the processor air duct from a Firepower MC1500 or MC3500:

Step 1 Observe the ESD precautions described in Working in an ESD Environment, page A-2 and the safety

precautions described in Safety Warnings, page A-2.

Step 2 Disconnect any cables attached to any add-in cards.

Step 3 Grasp both riser latches with thumb and forefinger and pull up to release the riser assembly.

Step 4 Lift riser assembly straight up (see “1” in Figure A-6).

Figure A-6 Removing the PCI Riser Assembly from a MC1500 or MC3500

Step 5 Set the riser assembly upside down to avoid damage to the riser card connector.

Step 6 Lift the processor air duct from its location over the two processor sockets (see “1” in Figure A-7).

1PCI riser assembly ——

A-9

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

Appendix A Memory Upgrade Instructions for Firepower Management Centers

Replacing the DIMMs

Figure A-7 Removing the Processor Air Duct from a MC1500 or MC3500

What to Do Next:

•Remove the MC1500 or MC3500 DIMMs as described in the “Replacing the DIMMs” section on

page A-9.

Replacing the DIMMs

To ensure the best appliance performance, it is important that you are familiar with memory requirement

guidelines and population rules before you install or replace memory modules. See Table A-1 in Memory

Upgrade Overview, page A-1 for a reminder of the default memory configurations that shipped with

Firepower Management Centers prior to the release of Firepower System 5.4.

Table A-3 below outlines the new memory requirements to run Firepower System 5.4 and greater.

Appliances that do not meet the minimum memory requirement are not supported.

1Processor air duct ——

Table A-3 Overview of Upgrade RAM Requirements

Management Center Model

RAM Required for Firepower

Version 5.4 and greater DIMM Location

MC750 (Rev. 1) 8 GB(2 x 4GB modules) A1 and B1

MC750 (Rev. 2) 8 GB(2 x 4GB modules) A1 and B1

MC1500 48 GB (3 x 16GB modules) A1, B1, and C1

MC3500 48 GB (3 x 16GB modules) A1, B1, and C1

A-10

Cisco Firepower Management Center 750, 1500, 2000, 3500, and 4000 Hardware Installation Guide

Appendix A Memory Upgrade Instructions for Firepower Management Centers

Replacing the DIMMs

DIMM Location and Orientation

On the Firepower MC750 (Rev. 1 or Rev. 2), MC1500, and MC3500, the DIMM connectors are located

on the system board and are identified by silkscreen labels. You can also refer to the Quick Reference

Label on the inside of the chassis cover to assist in locating components.

Tip Please note that only blue DIMM connectors are populated with modules.

DIMMs have a polarization notch on the mating edge to prevent incorrect insertion. Figure A-8 shows

the polarization notch on a DIMM.

Figure A-8 DIMM Showing Polarization Notch

Locating DIMMs in Firepower Management Centers

Use the following figures to identify the correct DIMM connectors for your memory upgrade

requirements identified in Table A-3. The silkscreen on the system board also displays the DIMM labels

starting from the center of the board.

•Refer to Figure A-9 for the location of the DIMM connectors on the MC750 (Rev. 1).

•Refer to Figure A-10 for the location of the DIMM connectors on the MC750 (Rev. 2).

•Refer to Figure A-11 for the location of the DIMM connectors on the MC1500 and MC3500.

1Polarization notch ——

Polarization notch

103362

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco L2TP Bedienungsanleitung

Cisco

Cisco SFS 7008P Bedienungs- und Wartungsanleitung

Cisco

Cisco AS5200-PWR-AC Stücklistenhandbuch

Cisco

Cisco B200 M3 Bedienungsanleitung

Cisco

Cisco CPS-UCS-2RU-K9 Bedienungsanleitung

Cisco

Cisco UCS C200 Montage- und Wartungsanleitung

Cisco

Cisco TelePresence Server 7010 Bedienungsanleitung

Cisco

Cisco UCS C220 M5SX Bedienungsanleitung

Cisco

Cisco UCS C220 M3 Systemhandbuch

Cisco

Cisco UCS B22 M3 Bedienungsanleitung

Cisco

Cisco UCS C24 M3 Bedienungsanleitung

Cisco

Cisco UCS B200 M4 Bedienungsanleitung

Cisco

Cisco UCS 5100 Kurzanleitung

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco UCS C240 M4 Montage- und Wartungsanleitung

Cisco

Cisco Business Edition 6000S Bedienungsanleitung

Cisco

Cisco UCS C Series Bedienungsanleitung

Cisco

Cisco C880 M5 Bedienungsanleitung

Cisco

Cisco UCS C220 Montage- und Wartungsanleitung

Cisco

Cisco UCS C460 Montage- und Wartungsanleitung

Cisco

Cisco UCS C24 Montage- und Wartungsanleitung

Cisco

Cisco UCS C460 M4 Bedienungsanleitung

Cisco

Cisco UCS B200 M3 Handbuch

Cisco

Cisco UCS C240 M5 Montage- und Wartungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung