Cisco UCS B Series Installations- und Betriebshandbuch

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco UCS B-Series Servers Upgrade Guide for

Intel E5-2600/E5 2400 v2 Series CPUs

Caution You must follow the procedures in this guide when upgrading an existing server to use Intel

E5-2600/E5-2400 v2 Series CPUs. Failure to follow these procedures might result in a non-bootable

server.

This document describes the process for successfully upgrading a Cisco UCS B-Series server to use Intel

E5-2600/E5-2400 v2 Series CPUs. Downgrade scenarios are also covered.

The procedures in this guide support the following servers:

•Cisco UCS B200 M3 blade server

•Cisco UCS B22 M3 blade server

Note Cisco UCS B200 Server Generation M2 does not support the Intel E5-2600 v2 Series CPUs.

Cisco UCS B-Series Servers Upgrade Guide for Intel E5-2600/E5 2400 v2 Series CPUs

OL-28629-02

Cisco UCS Blade Server

This section contains the following topics:

•Minimum Software and Firmware Requirements, page 2

•Upgrading the B200 M3 Server to Intel E5-2600 v2 Series CPUs, page 3

•Upgrading the B22 M3 Server to Intel E5-2400 v2 Series CPUs, page 9

•Downgrading the Cisco B200 M3 Server From Intel E5-2600 v2 Series CPUs, page 14

•Sample Board Controller Activation Command Sequence, page 15

•Downgrading the Cisco B22 M3 Server From Intel E5-2400 v2 Series CPUs, page 17

•Sample Board Controller Activation Command Sequence, page 18

Minimum Software and Firmware Requirements

Cisco UCS B200 M3 Requirements

The minimum software and firmware versions required for the Cisco UCS B200 M3 server to support

Intel E5-2600 v2 Series CPUs are as follows:

Cisco UCS B22 M3 Requirements

The minimum software and firmware versions required for the Cisco UCS B22 M3 server to support

Intel E5-2400 v2 Series CPUs are as follows:

Table 1 Cisco UCS B200 M3 Minimum Software and Firmware Requirements

Software or Firmware Minimum Version

Cisco UCS Manager 2.1(3a)

Server CIMC 2.1(3a)

Server BIOS 2.1(3a)

Board controller firmware 8.0

Table 2 Cisco UCS B22 M3 Minimum Software and Firmware Requirements

Software or Firmware Minimum Version

Cisco UCS Manager 2.2(2c)

Server CIMC 2.2(2c)

Server BIOS 2.2(2c)

Board controller firmware 13.0

Cisco UCS B-Series Servers Upgrade Guide for Intel E5-2600/E5 2400 v2 Series CPUs

OL-28629-02

Cisco UCS Blade Server

Upgrading the B200 M3 Server to Intel E5-2600 v2 Series CPUs

Note These upgrade procedures require server downtime.

This section contains the following topics:

•Upgrade Scenario 1: UCSM and BIOS Earlier Than Version 2.1(3a), CPU Earlier Than Intel

E5-2600 v2, page 4

•Upgrade Scenario 2: UCSM and BIOS at Version 2.1(3a) or Later, CPU Earlier Than Intel E5-2600

v2, page 5

•Upgrade Scenario 3: UCSM at Version 2.1(3a) or Later, CPU is Intel E5-2600 v2, BIOS on Spare

Earlier Than Version 2.1(3a), page 7

Cisco UCS B-Series Servers Upgrade Guide for Intel E5-2600/E5 2400 v2 Series CPUs

OL-28629-02

Cisco UCS Blade Server

Upgrade Scenario 1: UCSM and BIOS Earlier Than Version 2.1(3a), CPU Earlier Than Intel E5-2600 v2

This scenario assumes the following conditions:

•The Cisco UCS Manager software is at a version earlier than 2.1(3a).

•The server is at a BIOS/CIMC version earlier than 2.1(3a).

•The server is using CPUs earlier than Intel E5-2600 v2 Series.

In this case, use the following procedure to upgrade the server and CPUs.

Step 1 Upgrade the Cisco UCS Manager software to version 2.1(3a) or later. The required server CIMC and

BIOS are also included with the 2.1(3a) download bundle.

Use the procedures in the appropriate upgrade guide for Release 2.1 (depending on your current software

version): Release 2.1 Upgrade Guides.

Step 2 Use Cisco UCS Manager 2.1(3a) to upgrade and activate the server CIMC to version 2.1(3a) or later.

Use the procedures in the GUI or CLI Firmware Management Guide, Release 2.1.

Step 3 Use Cisco UCS Manager 2.1(3a) to upgrade and activate the server BIOS to version 2.1(3a) or later.

Use the procedures in the GUI or CLI Firmware Management Guide, Release 2.1.

Step 4 Disassociate the server in Cisco UCS Manager.

Step 5 Power off the server.

Step 6 Replace the CPUs with the Intel E5-2600 v2 Series CPUs.

Use the procedures in the Blade Server Installation and Service Note for your server.

Step 7 Reinsert the server to the chassis.

Step 8 Wait for Cisco UCS Manager to automatically discover the server.

Note At this point, the Health LED of the server shows a critical fault and Cisco UCS Manager reports

a generic error message: WILL_BOOT_FAULT: Sensor failure asserted. This is because a board

controller activation is required, as described in the next step.

Step 9 Perform a board controller activation by using the Cisco UCS Manager CLI interface. Use the following

sequence of commands:

Note The show image command in the sequence below lists the board controller versions available for

the server. Always activate the latest board controller image version when you use the

activate firmware command.

Note The server automatically reboots after the commit-buffer command is executed.

# scope server <chassis/server>

# scope boardcontroller

# show image

# activate firmware <boardcontroller version>.0 force

# commit-buffer

See also Sample Board Controller Activation Command Sequence, page 15.

Cisco UCS B-Series Servers Upgrade Guide for Intel E5-2600/E5 2400 v2 Series CPUs

OL-28629-02

Cisco UCS Blade Server

Step 10 Do not continue with the next step until the board controller activation completes. Verify whether the

activation is complete by using the show version command.

As shown in the example below, wait until the Activate-Status returns Ready. This process takes a few

minutes before the Activate-status is successfully completed and returns Ready.

# show version

BoardController:

Running-Vers: 8.0

Package-Vers:

Activate-Status: Ready

Step 11 Clear the WILL_BOOT_FAULT by using the Cisco UCS Manager GUI to reset the server CIMC:

a. In the Navigation pane, click the Equipment tab.

b. On the Equipment tab, expand Equipment > Chassis > Chassis number > Servers, then choose

your server.

c. In the Work pane, click the General tab.

d. In the Actions area, click Recover Server.

e. In the Recover Server dialog, click Reset CIMC (Server Controller), then click OK.

Wait for CIMC to reboot and for Cisco UCS Manager to do a shallow discovery of the server. This

takes two to three minutes. At the end of this process the WILL_BOOT_FAULT is cleared.

Upgrade Scenario 2: UCSM and BIOS at Version 2.1(3a) or Later, CPU Earlier Than Intel E5-2600 v2

This scenario assumes the following conditions:

•The Cisco UCS Manager software is at version 2.1(3a) or later.

•The server is already using BIOS/CIMC version 2.1(3a) or later.

•The server is using CPUs earlier than Intel E5-2600 v2 Series CPUs.

In this case, the server already has the software and firmware prerequisites. Use the following procedure

to upgrade the CPUs:

Step 1 Disassociate the server in Cisco UCS Manager.

Step 2 Power off the server.

Step 3 Replace the CPUs with the Intel E5-2600 v2 Series CPUs.

Use the procedures in the Blade Server Installation and Service Note for your server.

Step 4 Reinsert the server to the chassis.

Step 5 Wait for Cisco UCS Manager to automatically discover the server.

Note At this point, the Health LED of the server shows a critical fault and Cisco UCS Manager reports

a generic error message: WILL_BOOT_FAULT: Sensor failure asserted. This is because a board

controller activation is required, as described in the next step.

Step 6 Perform a board controller activation by using the Cisco UCS Manager CLI interface. Use the following

sequence of commands:

Cisco UCS B-Series Servers Upgrade Guide for Intel E5-2600/E5 2400 v2 Series CPUs

OL-28629-02

Cisco UCS Blade Server

Note The server automatically reboots after the commit-buffer command is executed.

Note The show image command in the sequence below lists the board controller versions available for

the server. Always activate the latest board controller image version when you use the

activate firmware command.

# scope server <chassis/server>

# scope boardcontroller

# show image

# activate firmware <boardcontroller version>.0 force

# commit-buffer

See also Sample Board Controller Activation Command Sequence, page 15.

Step 7 Do not continue with the next step until the board controller activation completes. Verify whether the

activation is complete by using the show version command.

As shown in the example below, wait until the Activate-Status returns Ready. This process takes a few

minutes before Activate-status is successfully completed and returns Ready.

# show version

BoardController:

Running-Vers: 8.0

Package-Vers:

Activate-Status: Ready

Step 8 Clear the WILL_BOOT_FAULT by using the Cisco UCS Manager GUI to reset the server CIMC:

a. In the Navigation pane, click the Equipment tab.

b. On the Equipment tab, expand Equipment > Chassis > Chassis number > Servers, then choose

your server.

c. In the Work pane, click the General tab.

d. In the Actions area, click Recover Server.

e. In the Recover Server dialog, click Reset CIMC (Server Controller), then click OK.

Wait for CIMC to reboot and for Cisco UCS Manager to do a shallow discovery of the server. This

takes two to three minutes. At the end of this process the WILL_BOOT_FAULT is cleared.

Cisco UCS B-Series Servers Upgrade Guide for Intel E5-2600/E5 2400 v2 Series CPUs

OL-28629-02

Cisco UCS Blade Server

Upgrade Scenario 3: UCSM at Version 2.1(3a) or Later, CPU is Intel E5-2600 v2, BIOS on Spare Earlier

Than Version 2.1(3a)

This scenario is unique to a field-service situation in which a server that is already running Intel E5-2600

v2 Series CPUs must be replaced, but the only replacement server available is running a BIOS earlier

than 2.1(3a).

This scenario assumes the following conditions:

•The Cisco UCS Manager software is at version 2.1(3a) or later.

•The replacement server is using Intel E5-2600 v2 Series CPUs (after the CPUs are transferred from

the old server).

•The replacement server is using BIOS/CIMC version earlier than 2.1(3a).

Use the following procedure to upgrade the replacement server BIOS to the required version:

Step 1 Disassociate the server in Cisco UCS Manager.

Step 2 Power off the server.

Step 3 Transfer the CPUs from the old server to the new replacement server.

Use the procedures in the Blade Server Installation and Service Note for your server.

Step 4 Insert the server into the chassis that is running Cisco UCS Manager 2.1(3a) or later.

Note The server does not boot and discovery of the server hangs waiting for BIOS POST to complete

because the BIOS is at an earlier version that does not support E5-2600 v2 Series CPUs.

Step 5 Use the Cisco UCS Manager CLI to upgrade the BIOS. Use the following sequence of commands:

Note The show image command in the sequence below lists the firmware versions available for the

server. Always activate the latest firmware image version when you use the

update firmware command.

# scope server <chassis/blade>

chassis/server # scope bios

chassis/server/bios # show image

chassis/server/bios # update firmware <server_model>.<firmware version>

chassis/server/bios* # commit-buffer

Step 6 Wait for the update to complete. Check the status of the update and wait until the following command

returns Status: Ready. It takes a few minutes for the Status to return Ready.

chassis/server/bios # show update status

Status: Ready

Step 7 Activate the new BIOS:

chassis/server/bios # activate firmware <server_model>.<firmware version>

Warning: When committed this command will reset the end-point

chassis/server/bios* # commit-buffer

chassis/server/bios # exit

Step 8 Power-cycle the server to get discovery out of the hang state:

chassis/server # cycle cycle-immediate

chassis/server* # commit-buffer

Cisco UCS B-Series Servers Upgrade Guide for Intel E5-2600/E5 2400 v2 Series CPUs

OL-28629-02

Cisco UCS Blade Server

Cisco UCS Manager is now able to complete auto-discovery of the server.

Step 9 Use Cisco UCS Manager 2.1(3a) to upgrade and activate the server CIMC to version 2.1(3a) or later.

Use the procedures in the GUI or CLI Firmware Management Guide, Release 2.1.

Step 10 Wait for the server to be discovered and by Cisco UCS Manager.

Step 11 Perform a board controller activation by using the Cisco UCS Manager CLI interface. Use the following

sequence of commands:

Note The server automatically reboots after the commit-buffer command is executed.

Note The show image command in the sequence below lists the board controller versions available for

the server. Always activate the latest board controller image version when you use the

activate firmware command.

# scope server <chassis/server>

# scope boardcontroller

# show image

# activate firmware <boardcontroller version>.0 force

# commit-buffer

See also Sample Board Controller Activation Command Sequence, page 15.

Step 12 Do not continue with the next step until the board controller activation completes. Verify whether the

activation is complete by using the show version command.

As shown in the example below, wait until the Activate-Status returns Ready. This process takes a few

minutes before Activate-status is successfully completed and returns Ready.

# show version

BoardController:

Running-Vers: 8.0

Package-Vers:

Activate-Status: Ready

Step 13 Clear the WILL_BOOT_FAULT by using the Cisco UCS Manager GUI to reset the server CIMC:

a. In the Navigation pane, click the Equipment tab.

b. On the Equipment tab, expand Equipment > Chassis > Chassis number > Servers, then choose

your server.

c. In the Work pane, click the General tab.

d. In the Actions area, click Recover Server.

e. In the Recover Server dialog, click Reset CIMC (Server Controller), then click OK.

Wait for CIMC to reboot and for Cisco UCS Manager to do a shallow discovery of the server. This

takes two to three minutes. At the end of this process the WILL_BOOT_FAULT is cleared.

Cisco UCS B-Series Servers Upgrade Guide for Intel E5-2600/E5 2400 v2 Series CPUs

OL-28629-02

Cisco UCS Blade Server

Upgrading the B22 M3 Server to Intel E5-2400 v2 Series CPUs

Note These upgrade procedures require server downtime.

This section contains the following topics:

•Upgrade Scenario 1: UCSM and BIOS Earlier Than Version 2.2(2c), CPU Earlier Than Intel

E5-2400 v2, page 10

•Upgrade Scenario 2: UCSM and BIOS at Version 2.2(2c) or Later, CPU Earlier Than Intel E5-2400

v2, page 11

•Upgrade Scenario 3: UCSM at Version 2.2(2c) or Later, CPU is Intel E5-2400 v2, BIOS on Spare

Earlier Than Version 2.2(2c), page 12

Cisco UCS B-Series Servers Upgrade Guide for Intel E5-2600/E5 2400 v2 Series CPUs

OL-28629-02

Cisco UCS Blade Server

Upgrade Scenario 1: UCSM and BIOS Earlier Than Version 2.2(2c), CPU Earlier Than Intel E5-2400 v2

This scenario assumes the following conditions:

•The Cisco UCS Manager software is at a version earlier than 2.2(2c).

•The server is at a BIOS/CIMC version earlier than 2.2(2c).

•The server is using CPUs earlier than Intel E5-2400 v2 Series.

In this case, use the following procedure to upgrade the server and CPUs.

Step 1 Upgrade the Cisco UCS Manager software to version 2.2(2c) or later. The required server CIMC and

BIOS are also included with the 2.2(2c) download bundle.

Use the procedures in the appropriate upgrade guide for Release 2.1 in the UCS Manager Install and

Upgrade Guides (depending on your current software version).

Step 2 Use Cisco UCS Manager 2.2(2c) to upgrade and activate the server CIMC to version 2.2(2c) or later.

Use the GUI or CLI procedures in the UCS Manager Install and Upgrade Guides.

Step 3 Use Cisco UCS Manager 2.2(2c) to upgrade and activate the server BIOS to version 2.2(2c) or later.

Use the GUI or CLI procedures in the UCS Manager Install and Upgrade Guides.

Step 4 Disassociate the server in Cisco UCS Manager.

Step 5 Power off the server.

Step 6 Replace the CPUs with the Intel E5-2400 v2 Series CPUs.

Use the procedures in the Blade Server Installation and Service Note for your server.

Step 7 Reinsert the server to the chassis.

Step 8 Wait for Cisco UCS Manager to automatically discover the server.

Note At this point, the Health LED of the server shows a critical fault and Cisco UCS Manager reports

a generic error message: WILL_BOOT_FAULT: Sensor failure asserted. This is because a board

controller activation is required, as described in the next step.

Step 9 Perform a board controller activation by using the Cisco UCS Manager CLI interface. Use the following

sequence of commands:

Note The show image command in the sequence below lists the board controller versions available for

the server. Always activate the latest board controller image version when you use the

activate firmware command.

Note The server automatically reboots after the commit-buffer command is executed.

# scope server <chassis/server>

# scope boardcontroller

# show image

# activate firmware <boardcontroller version>.0 force

# commit-buffer

See also Sample Board Controller Activation Command Sequence, page 15.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco UCS M3 Series Bedienungsanleitung

Cisco

Cisco UCS X9508 Kurzanleitung

Cisco

Cisco UCS B200 M3 Handbuch

Cisco

Cisco C880 M5 Bedienungsanleitung

Cisco

Cisco UCS B420 M4 Bedienungsanleitung

Cisco

Cisco APIC M4 Montage- und Wartungsanleitung

Cisco

Cisco expressway ce1100 Bedienungsanleitung

Cisco

Cisco UCS B420 M4 Handbuch

Cisco

Cisco UCS B200 M4 Handbuch

Cisco

Cisco TelePresence Server 7010 Bedienungsanleitung

Cisco

Cisco UCS B440-M1 Kurzanleitung

Cisco

Cisco ISE-3315 Bedienungsanleitung

Cisco

Cisco UCS B200 M4 Bedienungsanleitung

Cisco

Cisco Firepower 1120 Bedienungsanleitung

Cisco

Cisco C220 Handbuch

Cisco

Cisco UCS C22 Montage- und Wartungsanleitung

Cisco

Cisco 3500 Series Bedienungsanleitung

Cisco

Cisco UCS B460 M4 Bedienungsanleitung

Cisco

Cisco UCS X210c M6 Handbuch

Cisco

Cisco UCS B22 M3 Handbuch

Cisco

Cisco UCS C200 Handbuch

Cisco

Cisco MCS-7825-H1-IPC1 Bedienungsanleitung

Cisco

Cisco UCS 6500 Series Bedienungsanleitung

Cisco

Cisco CPS-UCS-2RU-K9 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung