Cisco UCS C220 Bedienungsanleitung

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco TelePresence Content Server Release 7.0

Quick Start Guide

March 2017

This document contains information about installing and configuring the Cisco TelePresence Content

Server Release 7.0. See these sections:

•Product Overview, page 2

•Technical Specifications, page 5

•Hardware and Software Limitations, page 5

•Installing the Content Server, page 5

•Completing the Initial Configuration, page 6

–

Task 1: Connect and power on the Content Server and configure CIMC, page 7

–

Task 2: Set the local administrator password, page 7

–

Task 3: Enter the Windows Server 2012 activation key

–

Task 4: Configure a static IP address, page 9

–

Task 5: Set the date and time, page 9

–

Task 6: Enable Remote Desktop Connection, page 9

–

Task 7: Configure SQL Settings

–

Task 8: Install a security certificate

–

Task 9: Configure the H.323/SIP registration settings

–

Task 10: Make a test recording

•Additional Content Server Setup, page 13

•Troubleshooting and Technical Support, page 15

•Related Documentation, page 15

•Providing Documentation Feedback, page 16

•Obtaining Documentation and Submitting a Service Request, page 16

Cisco TelePresence Content Server Release 7.0 Quick Start Guide

Product Overview

The Cisco TelePresence Content Server, allows you to share knowledge and enhance communication by

recording video conferences. You can access live and on-demand presentations anywhere, anytime. In

addition, you can distribute live or recorded content to any computer, or download to your favorite

portable media device.

This release introduces the fourth-generation Content Server hardware that runs Cisco Content Server

Release 7.0 software. The fourth-generation Content Server is based on the Cisco UCS C220 M4 server.

(For more information, see the Cisco UCS C220 Server Installation and Service Guide on Cisco.com.)

Figure 1 and Figure 2 show the Content Server front and rear panels, and Table 1 describes the server

features.

Figure 1 Content Server Front Panel

1Power button/Power status LED 6Power supply status LED

2Identification button/LED 7Network link activity LED

3System status LED 8Asset tag (serial number)

4Fan status LED 9KVM1connector—Use this port for initial

configuration

1. KVM = keyboard, video, and mouse

5Temperature status LED 10 Hard drives (two), hot-swappable (2.5-inch

drives installed in slots 1 and 2; slots 3 to 8 are

empty)

Cisco TelePresence Content Server Release 7.0 Quick Start Guide

Product Overview

Figure 2 Content Server Rear Panel: USB Port

Figure 3 Content Server Rear Panel: Lom Port

1Power supplies (two) 61-Gb Ethernet dedicated management port

(also see Figure 4)

2Low-profile PCIe slot 2 on riser

(half-height, half-length, x8 lane)

7Dual 1-Gb Ethernet ports:

LAN1 (Arrow 7, left pointer)—Use this port

to connect the Content Server to the

network (also see Figure 4)

LAN2 (Arrow 7, right pointer)—Not used

3Standard-profile PCIe slot on riser

(full-height, half-length, x16 lane)

8USB ports (two)

4VGA video connector 9Identification button/LED

5Serial port (RJ-45 connector)—Not used –

Table 1 Content Server Features

Chassis One rack-unit (1RU) chassis.

1.7 x 16.9 x 28.5 in. (4.32 x 43 x 72.4 cm)

Processors Two Intel Xeon E5-2665 processors.

Memory Four 8-Gb DDR31low-voltage DIMMs provide a total of 32 GB of memory.

Cisco TelePresence Content Server Release 7.0 Quick Start Guide

Product Overview

Baseboard

management

Integrated Emulex Pilot-3 baseboard management controller (BMC), running

Cisco Integrated Management Controller (CIMC) firmware.

IPMI 2.0 compliant for management and control.

One 10/100/1000 Ethernet out-of-band management interface.

CLI and web GUI management tool for automated, lights-out management.

Depending on your CIMC settings, the CIMC can be accessed through the

1-Gb Ethernet dedicated management port or the dual 1-Gb Ethernet LOM ports.

Network and

management I/O

The appliance provides these rear-panel connectors:

One 1-Gb Ethernet dedicated management port.

Two 1-Gb Base-T Ethernet ports.

One RS-232 serial port (RJ-45 connector).

One 15-pin VGA connector.

Two USB 2.0 connectors.

One front-panel KVM connector used with the included KVM cable that provides

two USB, one VGA, and one serial connector.

Front-panel

locator LED

One indicator light to help direct administrators to specific appliances in a data

center environment.

Power Up to two power supplies, 650 W each.

Redundant as 1+1. (Hot-pluggable when in a redundant configuration.)

Cooling Five hot-pluggable fan modules for front-to-rear cooling.

PCIe I/O Two Generation 3 PCIe2expansion slots on risers, occupied by a RAID3card

(LSI MegaRAID SAS9266-8i with SuperCap power module RAID backup unit,

configured for RAID 5) and a NIC4card (Broadcom 5709 quad port 1-Gb

Ethernet).

Note The Content Server does not support a dual NIC configuration.

Storage Drives are installed into front-panel drive bays that provide hot-pluggable access.

Small Form Factor—The appliance can hold up to eight 2.5 in x .55 in (63.5 mm x

14mm) SAS5or SATA6hard drives or solid state drives. The appliance ships with

two drives installed.

Hard disk option: 2.5-inch, 600 GB SAS hard drive that operates at 10,000 RPM.

Disk

Management

(RAID)

LSI MegaRAID 9266-8i (RAID 1).

RAID Backup There is an LSI battery backup unit for the LSI MegaRAID card.

Video Resolution up to 1600 x1200, 16 bpp at 60 Hz. Up to 256 MB of video memory.

1. DDR3 = double data rate, type 3

2. PCIe = peripheral component interconnect express

3. RAID = redundant array of independent disks

4. NIC = network interface card

5. SAS = serial attached SCSI

6. SATA = serial advanced technology attachment

Table 1 Content Server Features (continued)

Cisco TelePresence Content Server Release 7.0 Quick Start Guide

Technical Specifications

Environmental specifications and regulatory standards compliance for the Content Server are in the

product data sheet at this URL:

http://www.cisco.com/en/US/products/ps11347/products_data_sheets_list.html

Hardware Supported

Fourth Generation (M4 hardware)

•UCS C220 M4

•Intel(R) Xeon(R) CPU E5-2680 v3 @2.50GHz 24 cores

•64 GB RAM

Note This hardware specification is for TCS 7.0 Appliance on M4 hardware. TCS 7.0 Appliance is not

supported on third generation hardware.

TCS 7.0 VM is supported on third-generation, fourth-generation and third party hardware.

Hardware and Software Limitations

These are the software and hardware limitations:

•For TCS 7.0, there is no on-box streaming server as Windows Server 2012 doesn’t support Windows

Media Streaming server.For live streaming, TCS needs to be configured with external streaming

server.

•TCS 7.0 software cannot be installed on first, second or third generation Content Server hardware.

If you attempt to run the 7.0 installer it will fail.

•For TCS 7.0, fourth-generation Content Servers in a cluster must all be the same hardware version.

You cannot mix older (first, second or third generation) servers in a cluster with fourth-generation

Content Servers.

•The USB media kit is used only for a fourth-generation Content Server software reimage. You

cannot use the USB drive to upgrade the software on first, second or third generation server

hardware.

•On fourth-generation hardware, Content server is not supported on CIMC BIOS version 2.0(3e) with

manufacturing USB. It works fine with CIMC BIOS version 2.0(10e).

Installing the Content Server

Review these sections for installation information:

•Site Requirements and Safety Information, page 6

Cisco TelePresence Content Server Release 7.0 Quick Start Guide

Completing the Initial Configuration

•Shipping Carton Contents, page 6

•Rack Mounting, page 6

Site Requirements and Safety Information

Select and prepare an installation site that meets the requirements that are described in the Cisco UCS

C220 Server Installation and Service Guide on Cisco.com.

For specific compliance and safety information, see the Regulatory Compliance and Safety Information

for the Cisco UCS C-Series Servers on Cisco.com.

Shipping Carton Contents

When you receive the server, verify the contents of the shipping carton to ensure that you have all items

necessary for installation. Save the packing material in case you need to repack the server. If any item is

missing or damaged, contact your Cisco representative or reseller for instructions.

The contents of the shipping carton include these items:

•Content Server

•USB media kit (used only for a software reimage)

•Rail kit

•Serial cable

•Ethernet cable

•Cable kit power

•Accessory kit

•Printed card with URLs for product documentation and RoHS information for China

Rack Mounting

For Content Server rack mounting procedures, see the “Installing the Server” chapter of the Cisco UCS

C220 Server Installation and Service Guide.

Completing the Initial Configuration

You need these items to complete the Content Server initial configuration:

•USB keyboard, mouse, and VGA monitor.

•Windows Server 2012 product activation key—see the product activation key label on the Content

Server chassis.

•IP address, subnet mask, and gateway for:

–

Content Server.

–

Cisco Integrated Management Controller (CIMC) Configuration Utility.

These are the initial configuration tasks:

Cisco TelePresence Content Server Release 7.0 Quick Start Guide

Completing the Initial Configuration

•Task 1: Connect and power on the Content Server and configure CIMC, page 7

•Task 2: Set the local administrator password, page 7

•Task 3: Enter the Windows Server 2012 activation key, page 8

•Task 4: Configure a static IP address, page 9

•Task 5: Set the date and time, page 9

•Task 6: Enable Remote Desktop Connection, page 9

•Task 7: Configure SQL Settings

•Task 8: Install a security certificate

•Task 9: Configure the H.323/SIP registration settings

•Task 10: Make a test recording

Task 1: Connect and power on the Content Server and configure CIMC

Follow these steps:

Step 1 Attach a supplied power cord to each power supply in your server, and then attach the power cord to a

grounded AC power outlet. Wait for approximately two minutes to let the server boot in standby power

mode during the first bootup. You can verify power status by looking at the Power Status LED (Figure 1):

•Off—There is no AC power present in the server

•Amber—The server is in standby power mode. Power is supplied only to the CIMC and some

motherboard functions.

•Green—The server is in main power mode. Power is supplied to all server components.

Step 2 Use the supplied KVM cable to connect a USB keyboard, mouse, and a VGA monitor to the KVM

connector on the Content Server front panel (Figure 1).

Alternatively, you can use the VGA and USB ports on the rear panel. However, you cannot use the front

panel VGA and the rear panel VGA at the same time. If you do so, the first VGA connector is disabled.

Step 3 Press the Power button to boot the server. During bootup, press F8 when prompted to open the BIOS

CIMC Configuration Utility.

Step 4 Enter these settings in the CIMC Configuration Utility:

a. NIC Properties NIC mode: Dedicated

b. NIC Redundancy: None

c. IPv4 (Basic): CIMP ip-address, subnet-mask, gateway ip-address

Note The Content Server does not support dual NIC configuration.

Step 5 Press F10 to save your settings and restart the Content Server.

Task 2: Set the local administrator password

Follow these steps:

Cisco TelePresence Content Server Release 7.0 Quick Start Guide

Completing the Initial Configuration

Step 1 Log in to the Content Server Windows Server Manager by using the default password, Cisco123.

Step 2 Go to Start > Control Panel > User Accounts > Change your Windows password > Change your

password.

Step 3 In the Change your password window, enter the current password (Cisco123), the new password, and

confirm the new password.

Step 4 Click Change password.

Step 5 Click OK.

Task 3: Enter the Windows Server 2012 activation key

The Windows Server 2012 Physical Key is on the printed label on the Content Server top near the front.

You should have an Internet connection to access the Windows Server 2012 online activation service.

Follow these steps:

Step 1 Connect the Content Server to your network. Use an Ethernet cable to connect from your LAN to the

LAN1 network port, marked with blue in Figure 4, on the rear panel. Use the connector marked with red

for your CIMC management connection.

Figure 4 Network Connections

Step 2 Log in to the Content Server Windows Server Manager by using the password that you set in Task 2: Set

the local administrator password.

Step 3 Go to Start > Administrative Tools > Server Manager. In the Server Manager window, click Activate

Windows. Enter the Physical Key (located on the Content Server chassis label). Click Next.

If the Content Server is not connected to the Internet, you can follow the on-screen instructions to

activate Windows Server 2012 by using your phone.

Step 4 When the product key is verified and activated, click Close.

Cisco TelePresence Content Server Release 7.0 Quick Start Guide

Completing the Initial Configuration

Task 4: Configure a static IP address

By default, the server automatically acquires an IP address assigned by a DHCP server in your network.

We recommend that you change the IP address from DHCP to static. Follow these steps:

Step 1 Go to Start > Control Panel > Network and Internet.

Step 2 From the Network and Sharing Center, click View network status and tasks.

Step 3 In the Connect or disconnect section, click Local Connection.

Step 4 Choose IPv4 from the list. In the IPv4 Properties window, click the Use the following IP address radio

button. Enter the Content Server IPv4 address, subnet-mask, and default-gateway. Click OK.

Task 5: Set the date and time

You should set the Content Server date and time to ensure that the conference creation date and time

displays correctly in the Conference lists. Follow these steps:

Step 1 Log in to the Content Server by using the Administrator password that you set in Task 2: Set the local

administrator password.

Step 2 In the Server Manager window, click the time and date box in the lower right corner to open the settings

window. Or, go to Start > Control Panel > Clock, Language, and Region > Set the time and date.

Step 3 Click Change date and time settings.

Step 4 Update the date, time, and time zone. Click OK.

Task 6: Enable Remote Desktop Connection

Beginning with Cisco Content Server Release 7.0, all Windows Server 2012 administration and

configuration is accomplished by using Windows Remote Desktop Connection to access the server

administration interface. Follow these steps to enable remote desktop on the Content Server:

Step 1 Log in to the Content Server by using the Administrator password that you set in Task 2: Set the local

administrator password.

Step 2 Go to Start > Control Panel > System Security > System > Remote Settings.

Step 3 From the System Properties window Remote tab, select and click a radio button to enable Remote

Desktop on the Content Server. Click OK.

Step 4 Restart the Content Server. Go to Start > Log Off > Restart.

You can now disconnect the KVM cable from the Content Server and continue configuring the server by

accessing the Content Server user interface and by using Windows Remote Desktop Connection.

Cisco TelePresence Content Server Release 7.0 Quick Start Guide

Completing the Initial Configuration

Task 7: Configure SQL Settings

Step 1 Remote log in to the Content Server by using the Administrator password.

Step 2 Launch the Command Prompt.

Step 3 On the command prompt, type “cd c:\SQLConfig” to change the current directory to c:\SQLConfig

Step 4 Type SQLConfig.cmd to run the script. See the image, given below:

Figure 5 SQL Configuration

Step 5 Restart the Content Server. Go to Start > Log Off > Restart.

Task 8: Install a security certificate

The Content Server is shipped with a self-signed certificate, which is valid for ten years. Because

self-signed certificates are not from a trusted Certificate Authority, when users log in, most browsers will

display a message that the identity of the site could not be verified.

You can add the server to the Trusted sites list in Internet Explorer, or add an exception in Firefox to

avoid error messages at log in. However, we recommend purchasing a security certificate from a

certificate issuing authority that has a trusted relationship back to a root authority, such as VeriSign or

Comodo. These credentials are most likely to be trusted by browsers, which eliminates the need to add

the server to the list of Trusted sites. The certificate should be generated against the Windows machine

name or the DNS entry associated with the server IP address.

Follow these steps to install a purchased security certificate on the server default website:

Step 1 On your computer, go to Start > All Programs > Accessories > Remote Desktop Connection.

Step 2 In the Remote Desktop Connection dialog box, enter the IP address that you configured in Task 4:

Configure a static IP address.

Step 3 Click Connect. Log in with the administrator password that you set in Task 2: Set the local administrator

password. The Server Manager user interface appears.

Step 4 Go to Start > Internet Information Services (IIS) Manager.

Step 5 Under Connections, click the Content Server Windows 2012 server “machine_name (local computer)”.

Step 6 Click Server certificates in the machine_name Home window.

Step 7 Under Actions, click Import to import a new certificate.

Andere Handbücher für UCS C220

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco UCS B200 M4 Handbuch

Cisco

Cisco TelePresence Service-Handbuch

Cisco

Cisco APIC M3 Montage- und Wartungsanleitung

Cisco

Cisco UCS C220 M3 Systemhandbuch

Cisco

Cisco Catalyst 6800 Bedienungsanleitung

Cisco

Cisco UCS 5100 Bedienungsanleitung

Cisco

Cisco expressway ce1100 Bedienungsanleitung

Cisco

Cisco UCS B200 M4 Installations- und Betriebshandbuch

Cisco

Cisco UCS 5100 Handbuch

Cisco

Cisco ONS 15600 Bedienungsanleitung

Cisco

Cisco UCS C460 M4 Bedienungsanleitung

Cisco

Cisco AS5300-96VOIP-A Bedienungsanleitung

Cisco

Cisco UCS C22 M3 Systemhandbuch

Cisco

Cisco Expressway CE1200 Bedienungsanleitung

Cisco

Cisco NCS 1001 Bedienungsanleitung

Cisco

Cisco UCS B460 M4 Handbuch

Cisco

Cisco N20-B6625-1 Systemhandbuch

Cisco

Cisco SCE 8000 10GBE Bedienungsanleitung

Cisco

Cisco ONS 15454 SONET Bedienungsanleitung

Cisco

Cisco UCS C260 M2 Bedienungsanleitung

Cisco

Cisco UCS C220 M3 Bedienungsanleitung

Cisco

Cisco C880 M5 Bedienungsanleitung

Cisco

Cisco UCS C460 Bedienungsanleitung

Cisco

Cisco UCS B420 M3 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung