Cisco VCS Series Bedienungsanleitung

Cisco TelePresence

Video Communication

Server

Getting started

D14350.04

November 2010

Contents

Contents 2

General information 3

About the Cisco TelePresence Video Communication Server (Cisco VCS) 3

Installing the Cisco VCS 4

Package contents 4

Before you start 4

Preparing the installation site 4

Preparing the unit 4

Connecting the cables 4

Powering on the VCS 5

Initial configuration 6

Configuration using a serial cable 6

Configuration using the front panel 8

Using the Cisco VCS 9

Changing the admin account password 9

Changing the root account password 9

Other recommended configuration 9

Using the web interface 10

Using the Command Line Interface (CLI) 10

Documentation and training 11

Disclaimers and notices 12

VCS Getting Started Guide Page 2 of 12

General information

About the Cisco TelePresence Video Communication Server (Cisco

VCS)

The Cisco VCS enhances the video experience and provides seamless communication between SIP

and H.323 devices utilizing IETF and ITU standards. The Cisco VCS is the center of the video

communication network and connects all H.323 and SIP endpoints, infrastructure, and management

devices. The Cisco VCS provides unrivaled scalability and redundancy to video communications, and

is integral to interoperability with unified communications and Voice over IP systems.

The Cisco VCS can be deployed with either the Control application, the Expressway™ application or

the Cisco VCSStarter Pack Express application, with various optional packages including FindMe™

and Dual Network Interfaces.

VCS Getting Started Guide Page 3 of 12

Installing the Cisco VCS

Package contents

To avoid damage to the unit during transportation the Cisco VCS is delivered in a special shipping box,

which should contain the following components:

nCisco VCS unit

nrack ears, screws and Torx driver

nrubber feet

ncables:

lpower cables

lEthernet cable

lshielded serial cable

Report any discrepancies to your Cisco representative immediately.

We recommend that the shipping box is kept in case the Cisco VCS needs to be returned.

Before you start

IMPORTANT: Before installing the Cisco VCS, you must read the safety information at

www.cisco.com/go/telepresence/safety.

Preparing the installation site

Before installing the Cisco VCS:

nEnsure that the Cisco VCS is accessible and that all cables can be easily connected.

nEnsure that the power outlet is near to the Cisco VCS and is easily accessible.

nTo ensure adequate ventilation, leave a space of at least 10cm (4 inches) behind the VCS’s rear

panel and 10cm (4 inches) in front of the front panel.

nThe room in which you install the Cisco VCS should have an ambient temperature between 0ºC and

35ºC (32ºF and 95ºF) and between 10% and 90% non-condensing relative humidity.

nUse a grounded AC power outlet for the Cisco VCS.

Preparing the unit

1. Unpack the unit.

2. Mount the rack ears (using a Torx T10 driver) or rubber feet.

3. Turn the unit back on its feet or mount it in the rack.

If this product is mounted in a rack you are recommended to use additional support

accessories such as rack side support angles (rack angle brackets) or rack shelves, due to

the unit’s weight and depth. Contact your rack supplier to request the accessories best

suited for your rack.

Connecting the cables

1. Connect the power cable to the back of the Cisco VCS (see Figure 1).

2. Connect the Ethernet LAN cable from the LAN1 port on the front of the Cisco VCS to your network

(see Figure 2).

VCS Getting Started Guide Page 4 of 12

Installing the Cisco VCS

Powering on the VCS

1. Turn on the power switch on the back right of the unit (adjacent to the power cable). Press the soft

power button on the back left of the unit. The system will power up. Wait until:

lthe green PWR LED on the front of the unit is a steady green color (it may flash briefly during

power up)

lthe red ALM LED on the front of the unit has gone out

lthe IP address is showing in the display panel on the front of the unit

If the red ALM LED flashes rapidly it indicates a hardware fault. Contact your local Cisco

representative. The yellow HDD LED indicates disk activity and may flicker during normal

operation, more so on a busy system.

Figure 1: Cisco VCS back view

VCS Getting Started Guide Page 5 of 12

Initial configuration

Before you can use the Cisco VCS, you must configure its IPv4 address, subnet mask and default

gateway. Consult your network administrator for information on which addresses to use. Note that the

Cisco VCS must use a static IP address.

This initial configuration can be done:

nby connecting from a PC to the Cisco VCS using a serial cable. This is the recommended process,

and is described in the following section

nby using the buttons on the front panel (see "Configuration using the front panel" on page 8)

nif your network is set up to allow it, by connecting using a web browser to the default IP address of

192.168.0.100 (see "Using the web interface" on page 10)

Figure 2: Cisco VCS front view

Configuration using a serial cable

To set the initial configuration using a PC connected to the Cisco VCS DATA port via a serial cable:

1. Connect the Ethernet LAN cable from the LAN1 port on the front of the unit to your network.

2. Connect the supplied serial cable from the DATA port on the front of the unit to the serial port on a

PC.

3. Start a terminal emulator program on the PC and configure it to use the PC’s serial port as follows:

lbaud rate: 115200 bits per second

ldata bits: 8

lparity: none

lstop bits: 1

lflow control (hardware and software): none

Do not leave a terminal emulator session open after it is no longer in use. An open session

may cause issues during a system restart.

4. Turn on the power switch on the back right of the unit (adjacent to the power cable).

5. Press the soft power button on the back left of the unit. The system will power up. Wait until:

lthe green PWR LED on the front of the unit is a steady green color (it may flash briefly during

power up)

lthe red ALM LED on the front of the unit has gone out

lthe default IP address (192.168.0.100) is showing in the display panel on the front of the unit

The terminal emulator program on the PC will display the Cisco VCS’s startup information. After

approximately four minutes you will get the login prompt (if the Cisco VCS was already on when

you connected the serial cable, press Enter to get the login prompt):

tandberg login:

6. Enter the username admin and press Enter.

You will get the password prompt:

Password:

VCS Getting Started Guide Page 6 of 12

Initial configuration

7. Enter the default password of TANDBERG and press Enter.

You will get the install wizard prompt:

Run install wizard [n]:

8. Type yand press Enter.

9. Follow the prompts given by the install wizard to specify the following:

lthe password you want to use for your admin account

For security reasons you are advised to change the password from the default of

TANDBERG.

lwhether you want to use IPv4, IPv6 or Both

lthe LAN 1 IP address of the Cisco VCS

lthe LAN 1 IPv4 subnet mask of the Cisco VCS (if you have selected IPv4)

lthe IP default gateway of the Cisco VCS

lthe Ethernet speed

Use the default value of Auto unless the switch to which you are connecting is unable to

auto-negotiate.

lwhether you want to use SSH to administer the Cisco VCS

lwhether you want to use Telnet to administer the Cisco VCS

After the wizard is finished the following message will appear, and you will be prompted to log in

again:

Setting other settings...

OK. The system must be restarted for new

settings to take effect..

10. Login with the username admin and your new password.

11. You will again get the install wizard prompt; this time select nand press Enter in order to skip the

wizard.

A welcome message similar to the following will appear:

Welcome to

TANDBERG VCS Release X5.0

SW Release Date: 2009-09-09

12. You must now restart the system in order for the new settings take effect. To do this, type the

command:

xCommand restart

13. Disconnect the serial cable and store it in a safe place.

After it has rebooted, the Cisco VCS is ready to use. For security reasons you are advised to change

the password for the default admin account (if you have not already done so) and the root account from

the default of TANDBERG. See the sections "Changing the admin account password" on page 9 and

"Changing the root account password" on page 9 for details.

The IP configuration made using the install wizard applies to the LAN 1 Ethernet port only.

If you have enabled the LAN 2 port (by installing the Dual Network Interfaces option key)

you must use the web interface or CLI to configure the LAN 2 settings.

VCS Getting Started Guide Page 7 of 12

Initial configuration

Configuration using the front panel

The LCD panel and buttons at the front of the Cisco VCS allow you to configure and check the IP

settings as well as to reboot the system (see Figure 3). You are not recommended to perform the initial

configuration using the front panel, but you may need to use this method if you do not have access to a

PC and serial cable.

By default, during normal operation the front panel will show the system name (if configured) and one

of the following IP address, in order of priority:

nLAN 1 IPv4 address

nLAN 1 IPv6 address

nLAN 2 IPv4 address

nLAN 2 IPv6 address

Note that if the Cisco VCS is configured with a system name or IPv6 address that is longer than 16

characters, only the last 16 characters will be shown in the panel.

Figure 3: Cisco VCS LCD panel

To access the front panel menu options, press ENTER. The front panel LCD menu items are as

follows:

nTo navigate to a menu or submenu item, press UP/DOWN.

nTo select a menu or submenu item, press ENTER.

nTo produce the cursor in order to change a number, press ENTER.

nTo move the cursor left and right between the digits of a number, press UP/DOWN.

nTo select the digit you want to change, press ENTER.

nTo increase or decrease the value of the digit you are changing, press UP/DOWN; to select the

new value, press ENTER.

nTo navigate back to the submenu or menu, press ESC.

Note that the IPv4 address and IPv4 subnet mask configuration made using the front panel applies to

the LAN 1 port only. To configure the system’s IPv6 settings and (if you have the Dual Network

Interfaces option key installed) the LAN 2 settings, you must use the web interface or CLI.

VCS Getting Started Guide Page 8 of 12

Using the Cisco VCS

After you have set the initial configuration of the Cisco VCS, the system is ready to use. You can

continue to use the serial connection to access and manage the Cisco VCS, or you can connect to the

system remotely over IP using either or both:

nHTTPS (see "Using the web interface" on next page)

na command line interface via SSH or Telnet (see "Using the Command Line Interface (CLI)" on next

page)

For security reasons, you should change the passwords for the admin account and the root

account from the default of TANDBERG as soon as initial configuration of the Cisco VCS

has been completed.

Changing the admin account password

To change the password for the admin account using the web interface:

1. Navigate to Maintenance > Login accounts > Administrator accounts.

You will be taken to the Administrator accounts page.

2. Click on View/Edit for the admin name.

You will be taken to the Edit administrator account page.

3. In the Password and Confirm password fields, enter the new password, and click Save.

To change the password for the admin account using the CLI:

1. Type xConfiguration SystemUnit Password

You cannot set a blank password for the admin user or any other administrator account, or

the root account.

Changing the root account password

To change the password for the root account:

1. Using the CLI, log in as root.

2. Type passwd.

You will be asked for the new password.

3. Enter the new password and when prompted, retype the password.

4. Type exit to log out of the root account.

Other recommended configuration

You are now recommended to configure the following:

nThe system name of the Cisco VCS. This is used by the Cisco TelePresence Management Suite

(Cisco TMS) to identify the system. This can be set from the System administration page on the

web interface (navigate to System configuration > System).

nAutomatic discovery. If you have multiple Cisco VCSs in the same network you may want to

disable automatic discovery on some of them. This can be set from the H.323 page on the web

interface (navigate to VCS configuration > Protocols > H.323).

nThe DNS server address(es), if URI dialing or Fully Qualified Domain Names (FQDNs) are to be

used. This can be set from the DNS page on the web interface (navigate to System configuration

> DNS).

VCS Getting Started Guide Page 9 of 12

Using the Cisco VCS

Refer to the Cisco VCS Administrator Guide, deployment guides and release notes (available for

download from www.tandberg.com) or the online help for complete information on configuring these

and all other options available on your Cisco VCS.

Using the web interface

To use the web interface:

1. Open a browser window and in the address line type either:

lthe IP address of the Cisco VCS

lthe FQDN of the Cisco VCS

The Login page will appear.

2. Select Administrator Login.

3. Enter a valid administrator username and password and select Login.

You will be presented with the Overview page.

Refer to the online help or the Cisco VCS Administrator Guide for further information on the

configuration options available for each page of the Cisco VCS web interface.

Using the Command Line Interface (CLI)

The command line interface is available over SSH and through the serial port by default. Access using

Telnet can also be enabled.

To use the command line interface:

1. Start a SSH or Telnet session.

2. Enter the IP address or FQDN of the Cisco VCS.

3. Login with a username of admin and your system password.

You will see a welcome message.

For a full list of CLI commands available on the Cisco VCS, see the Command Reference appendix of

the Cisco VCS Administrator Guide.

VCS Getting Started Guide Page 10 of 12

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco MCS-7825-H1-IPC1 Bedienungsanleitung

Cisco

Cisco 700 series Installations- und Betriebshandbuch

Cisco

Cisco SFS 7008P Bedienungs- und Wartungsanleitung

Cisco

Cisco UCS C220 Montage- und Wartungsanleitung

Cisco

Cisco APIC M4 Montage- und Wartungsanleitung

Cisco

Cisco UCS E Series Bedienungsanleitung

Cisco

Cisco SCE 8000 10GBE Bedienungsanleitung

Cisco

Cisco UCS 5100 Bedienungsanleitung

Cisco

Cisco UCS C200 Montage- und Wartungsanleitung

Cisco

Cisco CRS-16 DC Bedienungsanleitung

Cisco

Cisco UCS X9508 Kurzanleitung

Cisco

Cisco UCS B440 M2 Bedienungsanleitung

Cisco

Cisco expressway ce1100 Bedienungsanleitung

Cisco

Cisco AS5800 Bedienungsanleitung

Cisco

Cisco UCS C460 M4 Installations- und Betriebshandbuch

Cisco

Cisco TelePresence Bedienungsanleitung

Cisco

Cisco SNS-3515 series Handbuch

Cisco

Cisco UCS C240 M5 Montage- und Wartungsanleitung

Cisco

Cisco TelePresence Server 7010 Technisches Datenblatt

Cisco

Cisco UCS C220 M5SX Bedienungsanleitung

Cisco

Cisco UCS C24 Montage- und Wartungsanleitung

Cisco

Cisco UCS C Series Montageanleitung

Cisco

Cisco UCS C460 Montage- und Wartungsanleitung

Cisco

Cisco UCS B460 M4 Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung