Cisco Aironet 600 Series Bedienungsanleitung

CHAPTER

3-1

Cisco Aironet 600 Series OfficeExtend Access Point User Guide

OL-29882-03

Configuring the Access Point

This chapter provides the following information:

•Configuring the Wireless LAN Controller IP Address on the Access Point, page 3-1

•Configuring Radio Channels on the Access Point, page 3-2

•Configuring Personal Wireless LANs, page 3-3

•Troubleshooting, page 3-4

Configuring the Wireless LAN Controller IP Address on the

Access Point

Follow these steps to configure the IP address of the Wireless LAN Controller on your Cisco Aironet

600 Series OfficeExtend access point.

Step 1 Obtain the IP address of your Wireless LAN controller from your company’s IT professional.

Step 2 Access the 600 Series OfficeExtend access point GUI as described in “Accessing the GUI” section on

page 2-1.

Step 3 Click the Configuration tab.

The Configuration page is displayed.

Step 4 From the Configuration page, click the WA N tab.

The WAN page is displayed.

Step 5 Enter the IP address of the primary controller in the Controller IP Address field.

Step 6 Leave the Static IP check box unchecked to allow the WAN IP address to be assigned by DHCP.

Step 7 Click Apply to commit your changes.

A verification screen is displayed.

Step 8 Click Continue.

The 600 Series OfficeExtend Access point will connect to the controller and download the current

software image. Allow the device 5 minutes to download and reboot with the new code and

configuration.

3-2

Cisco Aironet 600 Series OfficeExtend Access Point User Guide

OL-29882-03

Chapter 3 Configuring the Access Point

Configuring Radio Channels on the Access Point

Follow these steps to configure a radio channel for your 600 Series OfficeExtend access point.

Step 1 Access the 600 Series OfficeExtend access point GUI as described in “Accessing the GUI” section on

page 2-1.

Step 2 Click the Configuration tab.

The Configuration–System page is displayed.

Step 3 From the Radio Interface drop-down list, choose the desired radio interface, which can be either

2.4 GHz or 5 GHz.

Step 4 From the Status drop-down list, choose Enabled to enable the wireless interface.

Step 5 From the Channel Selection drop-down list, choose the channel on which this interface will operate.

Note 802.11n mode should be enabled by default. If it is disabled, choose Enabled from the

802.11 n-mode drop-down list.

Step 6 Click Apply to commit your changes.

3-3

Cisco Aironet 600 Series OfficeExtend Access Point User Guide

OL-29882-03

Chapter 3 Configuring the Access Point

Configuring Personal Wireless LANs

Step 1 Access the 600 Series OfficeExtend access point GUI as described in “Accessing the GUI” section on

page 2-1.

Step 2 Click the Configuration tab.

The Configuration–System page is displayed.

Step 3 Click the SSID tab.

The Configuration–SSID page is displayed.

Step 4 From the Band Selection drop-down list, choose the band, which can be either 2.4 GHz or 5.0 GHz. You

can duplicate the configuration on both bands, or have different settings on each band.

Step 5 Check the Enabled check box to enable this wireless connection. By default it is disabled.

Step 6 Check the Broadcast check box to broadcast the SSID over the air. By default it is unchecked.

Step 7 In the SSID field, enter the personal SSID that you want to assign to this access point. This SSID will

be locally switched. The default SSID is AIR-602 for both radios.

Note Your personal SSID Wireless LAN and your company SSID Wireless LAN are different. When

you configure your personal Wireless LAN, use an SSID name that is different from your

company’s SSID to help avoid confusion.

Step 8 From the Security drop-down boxes, enter the authentication type, encryption type, and passphrase. It is

suggested that you select WPA2-PSK and AES encryption.

Step 9 Click Apply to commit your changes.

A verification screen that is similar to the following, is displayed.

Step 10 Click Continue.

3-4

Cisco Aironet 600 Series OfficeExtend Access Point User Guide

OL-29882-03

Chapter 3 Configuring the Access Point

Troubleshooting

Problem LED Status Reasons Possible Solution

Private WLAN clients

can connect to the

Internet; but WLANs

provided by the

controller are unable to

connect or not being

broadcast.

LED cycling through

purple and orange with

client associated; LED

cycling with purple,

orange, and blue with no

client associated.

Access Point is in

CAPWAP Discovery

mode.

Verify that the correct

Wireless LAN

Controller IP address is

entered in the WAN

page of the 600 Series;

verify that CAPWAP

ports are allowed

through the personal

firewalls if any are

present on a router

between the 600 series

and the modem.

WLANs provided by the

controller are not

broadcast or clients are

unable to connect.

Blinking blue Software Upgrade in

Process.

Wait for 600 series to

finish code download

and perform an

automatic reboot.

No connectivity is

available through 600

Series access point.

Blinking orange No IP address on the

600 Series access point,

waiting for DHCP

address.

Restart your home

router/gateway or

modem followed by

your 600 Series access

point.

No connectivity is

available through 600

Series access point,

local GUI unavailable,

or other issues.

Orange Software Failure Disconnect and

reconnect power to the

600 Series access point.

The access point signal

strength is low.

Not applicable The access point may

not be in the optimal

position in relation to

your device(s). If the

access point is in close

proximity and above

your device, the signal

may become skewed.

Position the access

point lower than or with

the LED side facing

your devices.

Andere Handbücher für Aironet 600 Series

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco aironet 1810 series Bedienungsanleitung

Cisco

Cisco aironet 1522 Leitfaden

Cisco

Cisco Aironet 1815w Bedienungsanleitung

Cisco

Cisco WAP125 Service-Handbuch

Cisco

Cisco Aironet 1520 Series Bedienungsanleitung

Cisco

Cisco Aironet 350 Series Handbuch

Cisco

Cisco Aironet 1100 Series Bedienerhandbuch

Cisco

Cisco 1522AG - Aironet Lightweight Outdoor Mesh Access... Bedienungsanleitung

Cisco

Cisco Aironet 1570 Series Handbuch

Cisco

Cisco GR10-HW Bedienungsanleitung

Cisco

Cisco Small Business WAP551 Bedienungsanleitung

Cisco

Cisco Catalyst 9130 Bedienungsanleitung

Cisco

Cisco WAP150 Bedienungsanleitung

Cisco

Cisco Aironet 1530 Series Handbuch

Cisco

Cisco Digistar EoC Bedienungsanleitung

Cisco

Cisco Aironet 1200 Series Bedienungsanleitung

Cisco

Cisco Linksys WAP55AG Bedienungsanleitung

Cisco

Cisco Wap581 Bedienungsanleitung

Cisco

Cisco Meraki GR10 Bedienungsanleitung

Cisco

Cisco Meraki MR52 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Cisco

Cisco Cisco Aironet Wireless LAN Client Bedienungsanleitung

Cisco

Cisco WAP125 Bedienungsanleitung

Cisco

Cisco AIR-CAP1552H-x-K9 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung