Clarke STRONG-ARM CTJ2QLP Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0120 - ISS -2

2 TONNE GARAGE JACK

MODEL NO: CTJ2QLP

PART NO: 7621820

INTRODUCTION

Thank you for purchasing this CLARKE Garage Jack.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

SPECIFICATIONS

Model number CTJ2QLP

Weight 30kg

Dimensions (L x W x H) without handle 680 x 340 x (less wheels) x 210mm

Rated Load 2 tonne (2000kg)

Height of saddle from floor (minimum) 75 mm

Height of saddle from floor (maximum) 510 mm

Pump oil capacity 0.19L

Number of strokes min-max height 6

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SAFETY PRECAUTIONS

1. This jack is for lifting only, do not move a load using the jack as a dolly.

2. Do not use to lift people.

3. Always inspect the jack before use. Make sure that all parts are in good

condition and operating smoothly, and that no cracks or distortion is

apparent. If in doubt do not use. Have the damaged parts replaced or

consult your CLARKE dealer.

4. Make sure that the jack is on a firm, solid, level base, and that there is no

possibility of it slipping when under load.

5. Make sure the load is taken by the full saddle and that the point of lift on

the load, is strong enough to support the load adequately.

6. Do not work under the raised vehicle until it is supported by suitable means

e.g. axle stands, NEVER rely on the jack to support the vehicle by itself.

7. Never push a load off the jack.

8. Ensure that all personnel are well clear of a load being raised or lowered.

9. Do not try to lift more than the rated load for the jack, (See “Specifications”

on page 2.)

10. Do not use the jack if an oil leak is apparent. Consult your Clarke dealer.

11. Consult the vehicle handbook to determine the correct lifting points.

12. It is necessary that the operator watch the jack and the load during

operation.

13. Check the condition of the labels regularly and replace as required.

14. The jack must be maintained and repaired in accordance with the these

instructions and such work be carried out by qualified persons.

15. Do not make any adjustments to any valves on the jack.

WARNING: THE OPERATOR MUST FOLLOW ALL INSTRUCTIONS WITHIN THIS

INSTRUCTION BOOKLET

UNPACKING AND ASSEMBLY

1. Remove the retaining clip by

pressing the handle yoke down-

wards and pulling the clip away.

2. Loosen the bolt in the yoke until

the lower handle can be inserted

fully into the handle socket.

• The lower handle has a groove

which should engage with the

bolt once it is re-tightened.

• The socket in the handle will

engage with the jack control

valve at the base of the yoke.

3. Tighten the bolt to secure the

lower handle to the jack.

4. Add the upper handle by sliding it

onto the lower handle and secure

with the bolt provided.

OPERATION

This jack incorporates a twin piston pump with a ‘quick lift’ facility. This provides

the user with a rapid raising operation for the unloaded jack. When the jack

encounters a load (the vehicle to be raised), its distance raised per stroke

reduces to provide a gradual and controllable lifting operation.

Before use, inspect the jack for oil leaks or any other sign of damage. Should

any be apparent, have the jack repaired by a qualified technician.

1. 1.Ensure the vehicle to be raised is stable and on firm level ground with the

wheels chocked.

2. Position the jack so that the saddle is directly beneath the lifting point.

• Consult the vehicle handbook to determine suitable lifting points.

3. Twist the handle clockwise to close the control valve.

WARNING: NEVER WORK ON THE VEHICLE WHEN SUPPORTED ONLY BY A

JACK WHICH IS A HIGHLY DANGEROUS PRACTICE. THE VEHICLE MUST BE

SUPPORTED ON AXLE STANDS OR SUITABLE SUPPORTS, BENEATH THE

CORRECT JACKING/SUPPORT POINTS.

4. Pump the handle to raise the saddle until it reaches the jacking point.

5. Take care that no obstruction prevents a clean lift. Keep all personnel at a

safe distance before lifting the vehicle.

NOTE: The jack may move slightly during operation. It is important

therefore, that the floor is clean and completely free from debris.

6. Position axle stands directly beneath suitable supporting points on the

vehicle and very gently twist the handle anticlockwise.

• This will open the control valve to lower the load onto the stands.

7. To stop it lowering at any point, turn the handle clockwise again. Always

avoid a rapid descent by turning the handle slowly.

8. Carefully lower the vehicle onto the axle stand, checking constantly,

preferably with an assistant, that the vehicles jacking point rests snugly and

cleanly on the axle stand, and that the stand is stable before the weight is

taken.

NOTE: Ensure this operation is carried out under complete control. DO

NOT allow the load to drop suddenly as this could damage

internal parts.

9. Completely remove the jack from the vehicle.

MAINTENANCE

PURGING AIR FROM THE SYSTEM

If air bubbles become trapped inside

the hydraulic system, the efficiency

of the jack will be reduced. If the air

cannot be dispersed just by pumping

the handle with the valve open, it

can be purged from the system as

follows.

1. Turn the control valve counter-

clockwise, relieving the pressure

within the jack, then remove the

cover plate & oil filler plug.

• A broad-bladed screwdriver is required for the plug.

2. Pump the handle several times to purge air from the system.

3. Replace the oil filler plug, then turn the control valve clockwise and test the

jack. If efficiency is still low, check the oil level as below.

CHECKING /MAINTAINING THE OIL LEVEL

If the jack has been stored for long periods, check for oil leaks before use. If

necessary, check the oil level as follows:

1. Ensure the jack is fully lowered by turning the control valve anticlockwise.

2. Remove the cover plate and the oil filler plug.

• The oil should be almost level with the bottom of the oil filler hole.

• il can be topped up using Clarke Hydraulic Oil (p/no 3050830 for 1

litre).

3. Purge any air from the system and replace the oil filler plug.

4. Dispose of any old/spilled oil appropriately and wipe up any spillage.

GENERAL CARE

1. Periodically lubricate the hinges, front wheels & rear castors with light oil.

Should the arm become stiff, apply a shot of grease to the grease nipple

on the top of the lifting arm as shown above.

2. Store in a dry location.

3. In the event of damage or broken components, replacements are

available from Clarke Parts & Service.

STORAGE

1. Store in a dry place with the ram fully lowered. If stored for long periods,

inspect at least once a year, clean and re-oil. For servicing, contact your

CLARKE dealer, or CLARKE International Service Department.

ENVIRONMENTAL PROTECTION

One of the most damaging sources of environmental pollution is oil products.

Never throw away used hydraulic oil with domestic refuse or flush it down a

sink or drain. Collect any hydraulic oil in a leak proof container and take it to

your local waste disposal site.

If disposing of this product or any damaged components, do not dispose of

with general waste. This product contains valuable raw materials and should

be taken to your local civic amenity site for recycling of metal products.

TROUBLESHOOTING

DECLARATION OF CONFORMITY

PROBLEM CAUSE SOLUTION

Jack will not lift

the rated load

Low oil level See ‘Checking the Oil Level‘on p 6

Valve not closed Turn the release knob fully clockwise

Air in the system Purge the system as on p 5

Jack lower when

under load

Release valve not fully

closed

Turn the release knob fully clockwise

Air in the system Purge the system as on p 5

Pump feels

Spongy

Low oil level See ‘Checking the Oil Level‘on p 6

Air in the system Purge the system as on page 5

Jack will not lift

full height

Low oil level See ‘Checking the Oil Level‘on p 6

Air in the system Purge the system as on p 5

Jack will not

lower completely

Return spring may be

faulty

Return to your Clarke dealer for

repair

If any of these remedies fail to restore your jack, consult your Clarke dealer

COMPONENT PARTS - GENERAL ASSEMBLY

No Description No Description

1Circlip 20mm 18 Upper handle

2Washer 12mm 19 Lower handle

3Front wheel 20 Screw M6 x 35

4Chassis frame 21 U-joint

5Nut M16 22 Hydraulic unit

6Washer M16 23 Return spring

7Screw M5x12 24 Circlip 22mm

8Rear castor assembly 25 Connecting block

9Screw M10x 12 26 Split pin A4 x 55

10 Washer M10 27 Circlip 25mm

11 Yoke bolt 28 Lifting arm shaft

12 Washer M18 29 Cover plate

13 Circlip 12mm 30 Lifting arm

14 Yoke roller 31 Saddle

15 Handle yoke 32 Saddle screw

16 Yoke roller pin 33 Rubber pad

17 Handle set screw 34 Handle grip

COMPONENT PARTS-GENERAL ASSEMBLY

COMPONENT PARTS - HYDRAULIC PARTS

No Description No Description

1Sealing ring 22 High pressure piston housing

2Reservoir 23 O-ring 10 x 2.65 #

3Sealing ring 24 Retaining ring 15 x 10.6 x 1.25

4O-ring 29x3.55 # 25 High pressure piston

5Top nut 26 Spring

6Ram 27 Dust cover

7Circlip 30mm 28 Spring base

8Ram base 29 Retaining ring 15mm

9Washer 30 Universal joint

10 O-ring 24.6 x 5.1 # 31 Steel ball 6mm

11 Cylinder 32 Slow release valve seat

12 Copper sealing ring 33 Copper sealing ring

13 Body casting 34 Low pressure piston housing

14 Steel ball 4mm 35 O-rings 17X2.65 #

15 Valve base 36 Low pressure piston

16 Spring 37 Return spring

17 Safety valve screw 38 Dust cover

18 O-ring 7.1 x 1.8 39 Spring base

19 Safety valve end screw 40 Retaining ring 22mm

20 Steel ball 5mm 41 Slow release pin

21 Copper sealing ring 42 Slow release pin spring

• Items marked # are components of the Repair Seal Kit.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Jack Handbücher

Clarke

Clarke Strong-Arm CTJ 50 Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm CTJ2250Q Bedienungsanleitung

Clarke

Clarke CBJ32 Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ3000G Bedienungsanleitung

Clarke

Clarke CFJ60 Bedienungsanleitung

Clarke

Clarke Strong Arm CTJ3000GB Bedienungsanleitung

Clarke

Clarke CTJ2001G Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ3GLC Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ10GLB Bedienungsanleitung

Clarke

Clarke CTJ2000A Installations- und Betriebshandbuch

Clarke

Clarke STRONG-ARM VPJ300 Bedienungsanleitung

Clarke

Clarke Strong-Arm CTJ2GLS Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ3LQLPRO Installations- und Betriebshandbuch

Clarke

Clarke STRONG-ARM CTJ3000QLB Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ1500QL Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm CFT5 Leitfaden

Clarke

Clarke CTBJ5 Fehlerbehebungshandbuch

Clarke

Clarke STRONG-ARM CTJ5GLB Bedienungsanleitung

Clarke

Clarke Strong-Arm CTJ100 Installations- und Betriebshandbuch

Clarke

Clarke CTJ3QLGB Bedienungsanleitung

Clarke

Clarke CTJ1800AB Bedienungsanleitung

Clarke

Clarke STRONG-ARM VPJ300 Installations- und Betriebshandbuch

Clarke

Clarke STRONG-ARM CHDDWD Handbuch

Clarke

Clarke CTT320 Bedienungsanleitung

Beliebte Jack Handbücher anderer Marken

Omega Lift Equipment

Omega Lift Equipment 18122C Gebrauchsanweisung

Pittsburgh

Pittsburgh 58816 Montageanleitung

Unimec

Unimec TP Bedienungsanleitung

Sonic

Sonic 4800703 Bedienungsanleitung

BGS technic

BGS technic 70039 Bedienungsanleitung

TradeQuip

TradeQuip 1128T Bedienungsanleitung

VEVOR

VEVOR TJD-12000SP-F Bedienungsanleitung

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Bedienungsanleitung

Stels

Stels 51131 Bedienungsanleitung

Bushranger

Bushranger RJX01 Bedienungsanleitung

Valex

Valex 1650520 Bedienungsanleitung

Pfaff

Pfaff Merkur M0 Bedienungsanleitung

Beta

Beta 3050/K Beilage

Sealey

Sealey 1050CXHV Bedienungsanleitung

Jung

Jung JH Series Bedienungsanleitung

URIAH

URIAH UC200020 Bedienungsanleitung

Kennedy

Kennedy KSJ010 Bedienungsanleitung

Grizzly

Grizzly H8097 Bedienungsanleitung