Clarke STRONG-ARM CTJ5GLB Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0609

5 TONNE HEAVY DUTY LONG CHASSIS

TROLLEY JACK

MODEL NO: CTJ5GLB

PART NO: 7623055

INTRODUCTION

Thank you for purchasing this CLARKE 5 Tonne Heavy Duty Long Chassis Trolley

Jack.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself and

that of others around you, and you can look forward to your purchase giving you

long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months

from the date of purchase. Please keep your receipt which will be required as

proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered

with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be

returned to us without prior permission.

This guarantee does not effect your statutory rights.

SPECIFICATIONS

Model number CTJ5GLB

Part number 7623055

Length (not including handle): 1338 mm

Width 428 mm

Height 185 mm

Height of lifting cup (minimum) 165 mm

Height of lifting cup (maximum) 565 mm

Weight 85.5 kg

Rated Load 5 tonne

SAFETY PRECAUTIONS

1. This jack is for lifting only, do not move a load using the jack as a dolly.

2. Always inspect the jack before use. Make sure that all parts are in good

condition and operating smoothly, and that no cracks or distortion is apparent.

If in doubt do not use. Have the parts replaced or consult your CLARKE dealer.

3. Make sure that the jack is on a firm solid base, and there is no possibility of it

slipping when under load.

4. Make sure the load is taken by the full saddle and that the point of lift on the

load, is of sufficient strength to support the full load adequately.

5. Always use axle stands to stabilise the load once lifted. NEVER work on or under

aload unless it is fully and adequately supported. NEVER rely upon the jack to

hold the load in position.

6. Never push a load off the jack.

7. Ensure that all personnel are well clear of a load being raised, or lowered.

8. NEVER exceed the rated load for the jack (See “Specifications” on page 3.).

9. Do not use if an oil leak is apparent. Consult your Clarke dealer.

10. Consult the vehicle handbook to determine the correct lifting points.

PARTS IDENTIFICATION

RELEASE KNOB

SADDLE

COVER

FOOT PEDAL

CASTORS

FRONT WHEELS

HANDLE LOCK

BEFORE USE

ASSEMBLY

1. Insert the handle into position

2. Secure the handle by tightening the

bolt shown.

CHECK OIL LEVEL

With the jack in an upright position.

1. Open the release valve by turning

release knob counterclockwise.

2. Remove the cover as shown.

3. Remove the filler plug.

• Oil should be just up to the edge

of hole.

4. Fill if necessary with Clarke hydraulic

oil available from your local dealer.

LUBRICATE INTERNAL COMPONENTS

1. Open the release knob.

2. Pump the handle several strokes to ensure proper internal lubrication.

BLEED HYDRAULIC SYSTEM

During transportation, the jack may become "air-bound" causing spongy ram

action.

TO BLEED THE HYDRAULIC SYSTEM -

1. Close the release valve by turning

release knob clockwise.

2. Remove the cover as shown.

3. Remove the transport plug.

4. Pump the handle to raise the jack

up to full height,

5. Install the air vent plug (supplied).

6. Replace the cover.

The jack is now ready to use.

OPERATION

POSITIONING

Ensure the load is chocked and stable and on firm level ground.

1. Release the handle lock as shown on the right.

2. Turn the release knob counterclockwise, to lower

the lifting ram

3. Position the jack so that the saddle is directly

beneath the lifting point and that there are no

obstacles to prevent a clean lift, also, make sure

that all personnel are well away from the area,

before raising the vehicle.

TO LIFT

1. Close the release valve by turning the release

knob clockwise firmly.

2. Operate the jack by pumping the jack handle or foot pedal

• Make sure that the saddle is in full contact with the lifting point and that

there are no obstacles to prevent a clean lift.

3. Place axle stands beneath the vehicle.

• Ensure the axle stands are centred about the support point and

perfectly stable before full weight is taken.

• Ensure that the axle stands are in good condition and fully capable of

supporting the load.

• Ensure that the axle stands cannot move when supporting the load.

• DO NOT jerk the handle, ensure it lowers slowly and under complete

control on to the axle stands which must be correctly positioned and

take the weight evenly.

TO LOWER

1. Lift the vehicle slightly to remove the weight from any supports,

2. Remove any supports from beneath the vehicle.

3. Open the release valve by SLOWLY turning the release knob counterclockwise.

NOTE: Ensure this operation is carried out under complete control. DO NOT

allow the load to drop suddenly as this could damage internal

components.

4. Remove the jack from beneath the vehicle.

NOTE: The jack may move slightly during operation. It is important therefore

that the immediate vicinity is clean and completely free from debris.

MAINTENANCE

1. When the jack is not in use, keep the ram completely retracted and the release

valve closed.

2. Keep the jack clean and apply lubricating oil to all pivoting sections every

three months, or more often when it is used in a dusty work environment.

3. Frequently check oil level. For procedure See “Before use” on page 5..

4. Check the pump piston and piston rod periodically for signs of rust or corrosion.

Clean exposed area with clean oiled cloth.

5. Change the oil once a year, see below.

STORAGE

Store in a dry place, with the ram fully retracted. If stored for long periods,

inspect at least once a year, clean and re-oil. For servicing, contact your

CLARKE dealer, or CLARKE International Service Department.

CHANGING THE OIL

1. Lower the saddle as far as possible

2. Lift off the cover as shown.

3. Remove the air vent plug.

4. Lay the jack on its side to drain the

oil into a suitable container.

5. Dispose of the oil in accordence

with local regulations.

6. Fill with Clarke hydraulic oil

available from your local dealer.

7. Replace the air vent plug.

TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

Jack will not lift

the rated load

Low Oil Level See “Changing the oil” on page 8.

Release valve not

closed

Turn the release knob fully clockwise

Air in the hydraulic

system

Bleed the system See page 6

Jack lower

when under

load

Release valve not

closed

Turn the release knob fully clockwise

Air in the hydraulic

system

Bleed the system See page 6

Pump feels

Spongy

Low Oil Level See “Changing the oil” on page 8.

Air in the hydraulic

system

Bleed the system See page 6

Handle raises or

flies back under

load

Air in the hydraulic

system

Bleed the system See page 6

Jack will not lift

full height

Low Oil Level See “Changing the oil” on page 8.

Air in the hydraulic

system

Bleed the system See page 6

Jack will not

lower

completely

Return spring may

be faulty

See your Clarke Dealer

If any of these remedies fail to restore your jack, consult your Clarke dealer

For Spare Parts and Servicing, please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

EXPLODED DIAGRAM AND PARTS LIST

NO DESCRIPTION PART NO

1Ram Assembly CTJ5GLB01

2Front Wheel Assembly CTJ5GLB02

3Rear Castor Assembly CTJ5GLB03

4Saddle CTJ5GLB04

5Rubber Pad CTJ5GLB05

6Foot Pedal CTJ5GLB06

7Extension Spring CTJ5GLB07

8Handle Assembly CTJ5GLB08

9Release Knob CTJ5GLB09

10 Universal Joint Assembly CTJ5GLB10

11 Pump Piston Assembly CTJ5GLB11

12 Filler Plug CTJ5GLB12

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Jack Handbücher

Clarke

Clarke Strong-Arm CTJ100 Installations- und Betriebshandbuch

Clarke

Clarke CFTJ500 Fehlerbehebungshandbuch

Clarke

Clarke STRONG-ARM CTJ2500QLGB Installations- und Betriebshandbuch

Clarke

Clarke CTJ2000LP Bedienungsanleitung

Clarke

Clarke CTJ2500SUV Bedienungsanleitung

Clarke

Clarke CTJ2000LPB Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ1250A Bedienungsanleitung

Clarke

Clarke CBJ32 Bedienungsanleitung

Clarke

Clarke CTJ10GLS Bedienungsanleitung

Clarke

Clarke CTJ2001G Bedienungsanleitung

Clarke

Clarke strong-arm CBJ30 Fehlerbehebungshandbuch

Clarke

Clarke CTJ1250AC Bedienungsanleitung

Clarke

Clarke CTJ2000A Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm CTJ2250Q Bedienungsanleitung

Clarke

Clarke CTJ1800A Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ3GLC Bedienungsanleitung

Clarke

Clarke Strong Arm CTJ3000GB Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ1500QL Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm CBJ2B Fehlerbehebungshandbuch

Clarke

Clarke Strong-Arm CTJ5GLS Bedienungsanleitung

Clarke

Clarke Strong-Arm CTJ4000G Bedienungsanleitung

Clarke

Clarke CTJ3GLS Bedienungsanleitung

Clarke

Clarke STRONG-ARM CTJ3000QLB Bedienungsanleitung

Clarke

Clarke Strong-Arm CTJ1500QULP Bedienungsanleitung

Beliebte Jack Handbücher anderer Marken

Omega Lift Equipment

Omega Lift Equipment 18122C Gebrauchsanweisung

Pittsburgh

Pittsburgh 58816 Montageanleitung

Unimec

Unimec TP Bedienungsanleitung

Sonic

Sonic 4800703 Bedienungsanleitung

BGS technic

BGS technic 70039 Bedienungsanleitung

TradeQuip

TradeQuip 1128T Bedienungsanleitung

VEVOR

VEVOR TJD-12000SP-F Bedienungsanleitung

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Bedienungsanleitung

Stels

Stels 51131 Bedienungsanleitung

Valex

Valex 1650520 Bedienungsanleitung

Pfaff

Pfaff Merkur M0 Bedienungsanleitung

Beta

Beta 3050/K Beilage

Sealey

Sealey 1050CXHV Bedienungsanleitung

Jung

Jung JH Series Bedienungsanleitung

URIAH

URIAH UC200020 Bedienungsanleitung

Kennedy

Kennedy KSJ010 Bedienungsanleitung

Grizzly

Grizzly H8097 Bedienungsanleitung

SW-Stahl

SW-Stahl 20700L Bedienungsanleitung