Clarke CAT211 Installations- und Betriebshandbuch
OPERATING & MAINTENANCE
INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC1019 - ISS 1
3PC AIR BLOW GUN KIT
MODEL NO: CAT211
PART NO: 3120528
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE Blow Gun kit.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
Please keep these instructions in a safe place for future reference.
SPECIFICATION
COMPRESSED AIR REQUIREMENTS
Use only clean, dry, regulated compressed air as a power source.
A build-up of moisture or oil in the air compressor will accelerate wear and
corrosion in the tool. Ensure any moisture is drained from the compressor daily
and the inlet filter is kept clean.
If an unusually long air hose is required, (over 8 metres), the line pressure or the
hose inside diameter may need to be increased.
The hose must be rated at 150% of the max operating pressure of the tool.
If an automatic in-line filter/regulator is used, it will keep the tool in good
condition, but should be regularly checked.
Never exceed the maximum operating pressure for the air tool. It is
recommended that air pressure to this tool does not exceed 90 psi. Higher
pressures and dirty air will shorten the life of the tool due to faster wear and is a
possible safety hazard
Max Operating Pressure 90 psi (6.2 bar)
Air Inlet Size 1/4“BSP Female
Air Consumption 9.5 cfm (max @90psi)
Dimensions Pocket Blow Gun - 97 x 20 x 29mm (0.057kg)
Short nozzle Blow Gun - 130 x 140 x 21mm (0.13kg)
Long nozzle Blow Gun - 240 x 17 x 87mm (0.085kg)
WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU
ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF
COMPRESSORS AND COMPRESSED AIR SUPPLY.
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
GENERAL SAFETY RULES
THE WORK ENVIRONMENT
1. Keep the work area clean and tidy.
2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair
out of the way.
3. Keep children and visitors away - Do not let children handle the tool.
USE OF AIR POWERED TOOLS
1. Stay alert and use common sense - do not operate this air tool when you
are tired or under the influence of alcohol, drugs or medication.
2. Always wear eye protectors when using the air tool. Eye protectors must
provide protection from flying particles from the front and the side.
3. DO NOT use the blow gun when other persons or animals are nearby or
may be hit by flying debris caused by the blow gun.
4. DO NOT overreach - Keep proper footing and balance at all times.
5. Never use oxygen, CO2, combustible gasses or any type of bottled gas as
a source of power for this blow gun.
6. DO NOT connect the air supply hose with your finger on the trigger.
7. DO NOT exceed the maximum pressure for the air tool of 90 psi / 6.2 bar.
8. Keep the air supply hose away from heat, oil and sharp edges.
9. DO NOT fit the blow gun to a stand/clamping device that may damage it.
10. Check air hoses for leaks or worn condition before use and ensure that all
connections are secure.
11. Do not use the blow gun for any purpose than that described here.
12. DO NOT carry out any alterations or modifications to the blow gun.
13. Always disconnect from the air supply when performing any maintenance.
14. DO NOT use the blow gun if it is defective or operating abnormally.
15. Always maintain your blow gun with care.
16. DO NOT discharge this blow gun at any persons or animals.
CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN
PERSONAL INJURY AND/OR DAMAGE TO PROPERTY.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
17. DO NOT insert into any part of yours or anyone else’s body.
18. DO NOT point directly at a person’s skin or at a fire.
19. DO NOT carry the blow gun by the hose or with your finger on the trigger.
20. When not in use the blow gun must be disconnected from the air supply
and stored in a dry place out of the reach of children.
21. DO NOT store the blow gun where the temperature is below 0oC.
CONNECTING /DISCONNECTING THE AIR SUPPLY
1. Connect a suitable hose to the air inlet.
2. Connect the other end of the air hose to the air compressor.
3. Turn on the air supply and check for air leaks. Rectify any found before
proceeding.
• PTFE tape may be useful for sealing threaded connections.
4. Your blow gun is now ready for use.
5. Set the compressed air pressure to suit at the compressed airline regulator.
6. DO NOT disconnect the air supply hose until the compressed air has been
isolated at a shut off valve. Once the pressure has been released,
disconnect the air supply hose.
MAINTENANCE
1. Before use, drain any condensate from the airline filter and compressor.
2. Clean thoroughly after use with a suitable solvent.
Please note that outside factors may affect the blow gun operation and
efficiency. These include reduced compressor output, excessive drain on the
airline, moisture or restrictions in the air-line, or the use of connectors of
improper size or poor condition which will reduce air supply.
Your CLARKE blow gun has been designed to give long and trouble free
service. If, however, having followed the instructions in this booklet carefully,
you encounter problems, take the product to your local CLARKE dealer.
WARNING: MAKE SURE THAT THE BLOW GUN IS DISCONNECTED FROM THE
AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE
PROCEDURES.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
COMPONENT PARTS
No Description No Description
1 Main Housing 8 Button
2 Spring 9 Nozzle
3O-ring 10Largering
4 Valve stem 11 Small ring
5O-ring 12Largering
6 O-ring 13 O-ring
7 Valve seat 14 Air inlet
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
COMPONENT PARTS
No Description No Description
1 Main Housing 10 Valve stem
2 O-ring 11 O-ring
3 Connector 12 O-ring
4 O-ring 13 Small ring
5 Nozzle 14 Large ring
6 Nozzle sleeve 15 Trigger
7 Venturi tip 16 Pin
8 Spring 17 Air inlet
9 O-ring
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
COMPONENT PARTS
No Description No Description
1 Main Housing 7 O-ring
2 Air inlet 8 O-ring
3 Spring 9 Valve seat
4 Valve stem 10 Trigger
5 O-ring 11 Pin
6 O-ring 12 Air nozzle
Inhaltsverzeichnis
Andere Clarke Elektrowerkzeuge Handbücher
Clarke
Clarke STRONG-ARM CSA12F Bedienungsanleitung
Clarke
Clarke CBM 2 Installations- und Betriebshandbuch
Clarke
Clarke Metalworker CDP501F Installations- und Betriebshandbuch
Clarke
Clarke Strong-Arm AP500B Bedienungsanleitung
Clarke
Clarke ZX-R Pro Series Bedienungsanleitung
Clarke
Clarke CHG2000C Bedienungsanleitung
Clarke
Clarke CAT22B Installations- und Betriebshandbuch
Clarke
Clarke ECSS-1 Benutzerhandbuch
Clarke
Clarke BJ300 Bedienungsanleitung
Clarke
Clarke CHT674 Bedienungsanleitung
Clarke
Clarke Air TPG30PTC Bedienungsanleitung
Clarke
Clarke CBS16 Bedienungsanleitung
Clarke
Clarke PSW1 Bedienungsanleitung
Clarke
Clarke PRO236 Installations- und Betriebshandbuch
Clarke
Clarke Woodworker CJS1-C Installations- und Betriebshandbuch
Clarke
Clarke CSG1C Bedienungsanleitung
Clarke
Clarke CAT221B Bedienungsanleitung
Clarke
Clarke CMFTLi Bedienungsanleitung
Clarke
Clarke CWS200B Bedienungsanleitung
Clarke
Clarke CAT141 Installations- und Betriebshandbuch
