Clarke ECSS-1 Benutzerhandbuch

ASSEMBLY & INSTRUCTION

MANUAL

LS0409

CHAINSAW SHARPENER

MODEL: ECSS-1

Part No: 3402075

INTRODUCTION

Thank you for purchasing this CLARKE product

Before attempting to use the product, it is essential that you read this manual

thoroughly and carefully follow all instructions given. In doing so you will

ensure the safety of yourself and that of others around you, and you can also

look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools,

accessories and packaging should be sorted, taken to a recycling

centre and disposed of appropriately.

PARTS & SERVICE

For parts & Servicing, please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

SAFETY PRECAUTIONS

• Ensure your mains voltage corresponds to the voltage mentioned on the

rating plate.

• Persons with limited physical or mental abilities should not be allowed to use

this chainsaw sharpener, unless they are supervised by a qualified person.

• The unit is designed for sharpening all common chainsaw chains. Do not

use it for any other purpose.

• Do not sharpen damaged chainsaw chains.

• Do not operate the unit without the protective cover in place and make

sure that all parts are firmly assembled before starting the unit.

• When sharpening, always wear protective goggles. Wear suitable clothes.

Take off jewellery and tie long hair back.

• Protect your ears by wearing ear protectors.

• Do not operate the unit if it does not work correctly or has been dropped.

• Do not disassemble the unit and do not try to repair it yourself. Contact your

customer support.

CONTENTS

INTRODUCTION .............................................................................................. 2

GUARANTEE ................................................................................................... 2

ENVIRONMENTAL PROTECTION .................................................................... 2

PARTS & SERVICE ........................................................................................... 2

SAFETY PRECAUTIONS ................................................................................... 3

OPERATING HINTS .......................................................................................... 4

ELECTRICAL CONNECTIONS ........................................................................ 5

PARTS IDENTIFICATION .................................................................................. 6

ASSEMBLY ....................................................................................................... 7

OPERATING .................................................................................................... 8

MAINTENANCE AND CLEANING .................................................................. 10

SPECIFICATION ............................................................................................... 11

PARTS DIAGRAM ........................................................................................... 12

PARTS LIST ....................................................................................................... 13

DECLARATION OF CONFORMITY ................................................................. 14

OPERATING HINTS

• Before you sharpen the chainsaw chain check it for damages, such as:

- bent or abraded chain links.

- broken cutting teeth, loose rivets or broken rivet heads.

If any damage is found, replace the entire chain.

• A sharp chainsaw produces wood

chips and pulls itself into the timber

being cut. When it becomes blunt,

sawdust will start being produced

during cutting operations.

• You should sharpen the chain if you

notice that you have to use force to

cut through the timber, i.e. if the saw

does not “pull” anymore.

• Sharpen all cutting teeth as

uniformly as possible. This will ensure

smooth operation with a minimum of vibration. See Fig 1

• Blunt cutting teeth or parts

damaged by stones may cause an

inclined cut during chain saw

operation and may also increase

the wear on the running face of the

cutting teeth.

• The depth limiter bars must be

profiled by hand. Ensure that all

depth limiter bars are equal in

height. See Fig 2

• Ensure that all cutting teeth are

sharpened to the same cutting angle.

• During sharpening occasionally check that the cutting-angle is set

correctly, as this setting may go out

of adjustment due to vibration.

• Make sure that all teeth are

sharpened as evenly as possible.

Only sharpen the teeth, never the

chain links.

• Sharpening teeth to unequal blade

lengths can cause a side drift when

sawing. see Fig 3.

Cutting tooth

is damaged

Cutting tooth

is OK

Fig 1

Fig 2

Fig 3

Depth limiting bar

Tooth size unequal

Tooth size equal

✓

ELECTRICAL CONNECTIONS

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

Before switching the product on, make sure that the voltage of your electricity supply

is the same as that indicated on the rating plate. This product is designed to operate

on 230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE

If the colours of the wires in the power cable of this product do not correspond with

the markings on the terminals of your plug, proceed as follows.

•The wire which is coloured Blue must be connected to the terminal which is

marked N or coloured Black.

• The wire which is coloured Brown must be connected to the terminal which

is marked L or coloured Red.

Plug must be BS1363/A approved

Always fit a 5 Amp fuse

Neutral

(Blue) Live

(Brown)

Ensure that the outer sheath of the cable is firmly held by the clamp

We strongly recommend that this machine is connected to the mains supply via a

Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

This symbol indicates that this is a Class II product, and does not require an

earth connection.

PARTS IDENTIFICATION

AetalPesaBIwercSgnitsujdA

BhctiwSFFO/NOJylbmessAredloHniahC

CeldnaHKrotacidnIelgnA

DrevoCevitcetorPLwercStnemtsujdAe

lgnA

EcsiDgnidnirGMsdraoBediuG

FwercSgninetsaFNretimiLhtpeD

GegdeWtnemtsujdAOseloHgnitnuoM

HredloHniahC

ASSEMBLY

The chain saw sharpener is supplied only partly assembled.

1. Remove the bolts from both

pivot clamps as shown in Fig 4.

2. Insert the axle into the body of

the chainsaw sharpener. Fig 5.

3. Place the chainsaw sharpener

on the base plate.

•Make sure the nipple on the

chainsaw sharpener is

positioned inside the depth

limiter (N) spring as shown in

Fig 6.

4. Replace the pivot clamps and

secure in place using the bolts

removed in step 1.

Note: Before starting the unit,

make sure the grinding

disc is fixed firmly. Never

operate the unit without the

protective cover.

5. Place the base plate (A) on a

solid, level surface, e.g. a

workbench. Fig 7.

•Ensure that the base plate

extends out far enough over

the edge of the work bench

so that the chain can hang

down freely and you can

easily access the angle

adjustment screw (L) at the

bottom.

6. Mount the base plate (A) using

the mounting holes (O).

The chain saw sharpener is now

ready for use.

Fig 4

Fig 5

Fig 6

Fig 7

OPERATING

WHEN SHARPENING, ALWAYS WEAR SAFETY GOGGLES.

FITTING THE CHAIN TO THE

SHARPENER

1. Lift up the adjustment wedge

(G) and unscrew the fastening

screw (F), see Fig 8.

2. Place the chainsaw chain on

the chain holder assembly (J).

•There is a diagram on the

chainsaw holder indicating

which way the teeth should

be facing

ADJUSTMENTS

ADJUSTING THE GRINDING ANGLE

1. Rotate the chain holder

assembly (J) to the required

angle.

•Most chainsaw chains have a

cutting tooth angle of 15° or

30°. Check the chain

packaging for infomation.

2. Tighten the angle adjustment screw (L).

•Do not over tighten. The chain holder assembly should be able to

move when required but it must stay in the set position when

sharpening.

•Do not rotate the chain holder assembly (J) when the grinding disc

is moving.

•The chain holder assembly (J) clicks into place at 15° or 30°

degrees, shown by the angle indicator (K), see Fig 9.

ADJUSTING THE MAXIMUM SHARPENING DEPTH

3. Adjust the maximum sharpening depth using the depth limiter (N).

• Start grinding with the most worn-out tooth and sharpen all other

teeth to the same depth.

Fig 8

Fig 9

SWITCHING ON/OFF

6. To switch on, set the ON/OFF

switch to the ( I ) position. see Fig

7. To switch off, set the ON/OFF

switch to the ( O ) position. see

Fig 10

SHARPENING THE CHAIN

8. Make sure the chainsaw chain is

held securly between both guide

boards (M). Tighten with the

fastening screw (F) if nessecery.

see Fig 11.

9. Position the tooth being

sharpened near to the grinding

disc.

10. Put the adjustment wedge (G)

down into position (fig 12) and

move the tooth forward with the

adjusting screw(I) until the

bottom of the grinding disc (E)

can be positioned inside the

cutting edge of the tooth. See Fig

13.

•Before moving the chain to the

next tooth, switch the unit off

and wait until the grinding disc

comes to a complete stop.

• First sharpen all teeth in one

direction i. e. every second

tooth.

• Then change the sharpening

angle to the opposite

direction.

• Make sure that all teeth are

sharpened as evenly as

possible.

• Only sharpen the teeth, never the chain links.

Fig 12

Fig 13

Fig 11

Fig 10

MAINTENANCE AND CLEANING

• Use a dry paint-brush to clean the unit and remove grinding

residues.

• Do not clean the unit with aggressive detergents or chemicals.

• The unit does not require any lubrication.

CHANGING THE GRINDING DISC

BEFORE CARRYING OUT ANY WORK ON THE CHAIN SAW SHARPENER

DISCONNECT THE PLUG FROM MAINS SUPPLY.

1. Unscrew the bolts indicated

using the hexagonal key

supplied and remove the

protective cover (D). See Fig 14.

2. Use the wrench supplied to lock

the spindle and then loosen the

nut with the socket wrench.

3. Place the new grinding disc over

the spindle.

• Only use grinding discs with a

diameter of 100 mm.

• Replacement grinding disc

speed must meet or exceed

the RPM rating of the unit.

Note: Replacement discs are available from your Clarke dealer part

number (3402076)

4. Tighten the nut and mount the protective cover (D) on the unit.

Fig 14

Fig 15

Inhaltsverzeichnis

Andere Clarke Elektrowerkzeuge Handbücher

Clarke

Clarke STRONG-ARM CSA10BB Bedienungsanleitung

Clarke

Clarke Contractor CON15 Installations- und Betriebshandbuch

Clarke

Clarke CBTSR Bedienungsanleitung

Clarke

Clarke CAT51 Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm CSA30FPB Bedienungsanleitung

Clarke

Clarke PRO236 Installations- und Betriebshandbuch

Clarke

Clarke CONTRACTOR CON1450WC Fehlerbehebungshandbuch

Clarke

Clarke CAT55 Installations- und Betriebshandbuch

Clarke

Clarke STRONG-ARM CSA50FP Fehlerbehebungshandbuch

Clarke

Clarke CBS16 Bedienungsanleitung

Clarke

Clarke CMFT300QR Bedienungsanleitung

Clarke

Clarke METALWORKER CMPS1 Bedienungsanleitung

Clarke

Clarke MetalWorker CDP151B Installations- und Betriebshandbuch

Clarke

Clarke CAT21B Installations- und Betriebshandbuch

Clarke

Clarke CAT50 Installations- und Betriebshandbuch

Clarke

Clarke Strong-Arm ARBOR PRESS Series Bedienungsanleitung

Clarke

Clarke Strong-Arm AHP 26 Bedienungsanleitung

Clarke

Clarke CHG1500D Bedienungsanleitung

Clarke

Clarke Air 25C Installations- und Betriebshandbuch

Clarke

Clarke CPSB100B Bedienungsanleitung

Clarke

Clarke CIR450C Installations- und Betriebshandbuch

Clarke

Clarke Air TPG30PTC Bedienungsanleitung

Clarke

Clarke RI150LI Bedienungsanleitung

Clarke

Clarke STRONG-ARM CSA12F Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch