Clarke Strong-arm AHP 16 Bedienungsanleitung

WARNING: Read these instructions before using the machine

OPERATION & MAINTENANCE

INSTRUCTIONS

LS1211

15 TONNE HYDRAULIC PRESS

MODEL NO: AHP 16

PART NO: 7615103

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

INTRODUCTION

Thank you for purchasing this CLARKE 15 tonne Hydraulic Press

Before attempting to operate the machine, it is essential that you read this

manual thoroughly and carefully follow all instructions given. In doing so you

will ensure the safety of yourself and that of others around you, and you can

also look forward to the press giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SAFETY PRECAUTIONS

• During assembly or if the press is moved, ALWAYS use a suitable crane or hoist,

do not manhandle.

• Ensure the press is located on firm level ground with adequate light.

• Before applying a load, ensure both press bed support pins are fully

engaged.

• Ensure that hydraulic hoses and couplings are completely sound.

• Before use, always ensure the workpiece is firmly secure and stable.

• Always clean spills of hydraulic oil immediately as this can be dangerous in a

workshop environment.

• Do not exceed the rated capacity of the press.

• Do not allow any person who is inexperienced in the use of hydraulic presses,

to use the press unless they are under direct supervision.

• Do not allow anyone to work directly in front of the press when it is in use.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

• Never tamper with the press. The safety valve is calibrated and sealed at the

factory; do not attempt to change the setting.

• Use only the recommended hydraulic oil.

• Components of this press are specially designed to withstand the rated

capacity. Do not substitute bolts, pins, or any other components.

• Always apply the load under the centre of the ram. Offset loads can

damage the ram or ram mount and may cause the work piece to eject.

• Before operating, check for signs of cracked welds, bent bed pins, loose or

missing bolts, or any other structural damage. Do not operate if any of these

conditions exist. Have repairs made only by authorised service centre.

• Remove load from press bed before attempting to adjust bed height.

• Press only on a work piece supported by the press bed.

• When using accessories such as arbor plates, be certain they are centered

below the ram and are in full contact with the bed.

• Parts being pressed may splinter, shatter, or be ejected from the press. Due to

varied applications, it is your responsibility to always use adequate guards,

wear eye protection and protective clothing when operating this press.

• Keep hands and fingers away from parts that may pinch and shift.

• Keep warning decals legible and intact. Replacements may be obtained

from Clarke International Spare Parts Department.

• Failure to heed these warnings may result in damage to the equipment, or

failure resulting in property damage, personal, or even fatal injury.

• DO NOT use extension tubes on the pump handle. Excessive effort can cause

damage and/or accidents.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

ASSEMBLY

Ensure the press and its components suffered no damage during transit.

Should any damage be apparent, please contact your CLARKE dealer

immediately.

IMPORTANT: Due to the weight of the press, we recommend that you get

assistance from another person during assembly.

1. With the main frame upright and adequately supported, bolt on the two

feet using the nuts and bolts supplied.

IMPORTANT: We strongly recommend that the press be firmly secured to a

firm and level floor using expansion bolts (not supplied).

2. Remove the plug on the front of the pump body and replace it with the

vent plug supplied.

3. Remove the cap on top of the ram. Seal the thread with PTFE tape and

screw in the pressure gauge, ensuring it is tight.

4. Fit the pump handle into the actuating lever.

NOTE: Do not locate your press where it will be open to the elements, as it is

designed to operate at temperatures of between -10OC to 40OC. Severe

weather conditions will damage the hydraulic system.

5. Insert the two supporting pins into the lowest holes on the frame, one each

side.

6. With assistance place the bed on top of the two pins.

BED HEIGHT

Position the bed at the desired height, so as it will be as close as possible to the

ram when the workpiece is mounted.

IMPORTANT: Due to the weight of the bed, we recommend that you get

assistance from another person when adjusting the bed height.

1. Raise one side of the bed, and insert a supporting pin into the next locating

hole.

2. Repeat at the other end of the bed to level out the bed,

3. Repeat steps 1 and 2 until the bed is at the desired height, with the

supporting pins fully ‘home’.

CAUTION: THE BED HEIGHT SHOULD ONLY BE RAISED OR LOWERED 1

HOLE AT A TIME, WORKING ALTERNATELY FROM ONE SIDE AND THEN THE

OTHER, FAILURE TO WORK IN THIS WAY MAY CAUSE THE BED TO FALL

AND CAUSE INJURY TO THE OPERATOR

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

POSITIONING THE RAM

The ram can positioned as required

by sliding it along the top rail.

• Always position the ram directly

above the workpiece.

HYDRAULIC PUMP/RAM OPERATION

The pump is provided with two valves, operated by turning the respective

handwheel as shown.

Valve A is used for raising or lowering

the ram.

Turn the handwheel clockwise and

pump the handle to operate (or

lower) the ram. Turning the

handwheel anticlockwise releases

the pressure and the ram will rise.

Valve B is used to move the ram in

fast or slow mode.

Turn the handwheel clockwise and

pump the handle to move the ram quickly to the workpiece. Turning the

handwheel anticlockwise and pumping the handle moves the ram at a slower

rate.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

OPERATION

1. Place the workpiece on the bed.

• It must be completely stable. you must use packing or shims where required.

‘Vee’ blocks and a supporting plate are supplied, which locate on the bed.

Place the workpiece on a combination of these to give it stability.

DO NOT ‘point load’ these accessories as they are not designed to take the full

force of the ram in one spot. Ensure they are adequately supported.

NOTE: Any packing pieces or shims used MUST be capable of

withstanding the pressure that will be brought to bear, and MUST

be of sufficient size with sufficient surface area, so as to avoid the

possibility of slipping or springing out. Mating surfaces MUST be

horizontal so that the force being exerted will NOT be at an angle.

2. Turn the Handwheel B, clockwise

to move the ram quickly, and

Handwheel A, clockwise to lower

the ram.

3. Pump the handle to bring the ram

very lightly into contact with the

workpiece.

4. Manoeuvre the workpiece or slide

the ram so that the desired point

of contact is directly beneath the

centre of the ram.

5. When satisfied that the workpiece

is correctly lined up and is

completely stable in that position,

ensure the handwheel B, is turned

ANTICLOCKWISE, and slowly pump the handle so that the ram begins to

exert pressure on the workpiece.

Continue to pump the handle whilst standing to the side. Do NOT stand

directly in front of the work, and constantly monitor the process, ensuring

the ram and work remain completely in line, and there is no risk of slipping.

6. When the process is complete, turn the handwheel A, anticlockwise to

release ram pressure.

WARNING: NEVER use extensions to the ram pumping handle

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

MAINTENANCE

A visual inspection must be made before each use of the press, checking for

leaking hydraulic fluid, and damaged, loose or missing parts.

Owners and/or users should be aware that repair of this equipment may

require specialised knowledge and facilities. It is recommended that a

thorough annual inspection of the press be made and that any defective

parts, decals or warning labels be replaced with genuine Clarke parts.

Any press which appears to be damaged in any way, is found to be badly

worn, or operates abnormally SHOULD BE REMOVED FROM SERVICE until the

necessary repairs are made.

PERIODICALLY

• Check the press frame to make sure all bolts are tight and inspect for

cracked welds, bent, loose or missing parts.

• Check the hydraulic connections for leaks. Replace or properly repair any

damaged or leaking hydraulic components before using.

EVERY 6 MONTHS

• Check the hydraulic pump oil level, by removing the plug from the front of

the unit. Oil should be level with the bottom of the hole. If necessary top up

with CLARKE Hydraulic Oil, Part No. 3050830 only. This operation is carried out

with the ram fully retracted.

EVERY 2 YEARS

• Replace the hydraulic oil. This operation requires the dismantling of the

hydraulic system, for which you should consult your CLARKE dealer.

• If any rust is apparent it must be removed completely and reinspected.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

SPECIFICATIONS

Capacity 15 tonne Dimensions

Pressure 390 Bar A 170 mm

Ram Stroke 160 mm B 550 mm

Ram Diameter 40 mm C 1000 mm

Net Weight 120 kg D 125 mm

E 160 mm

F 900 mm

G 600 mm

H 1950 mm

L 125 mm

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

PARTS DIAGRAM

PART NO DESCRIPTION PART NO DESCRIPTION

A0315 Nut M12 R0266 Spacer

A0346 Washer 12 x 24 R1182 Pump Assembly

B4949 Bolt TE M12 x 40 R1651 Flexible pipe

B5047 Gasket with 1/4” seal R1656 Working Plane

B5863 Connector for gauge R1664 V-Block

R0046 Nut M12 R1668XX Foot

R0058 Pressure Gauge R1673XX Frame

R0093 Bed Supporting Pin 25 x

320mm

R1680 Cylinder Assembly

R0132 Washer 3/8” R3053 Connector M-M 1/4” X3/8”

R0140 Bolt TE M12 x 90

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

DECLARATION OF CONFORMITY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Elektrowerkzeuge Handbücher

Clarke

Clarke CAT210 Installations- und Betriebshandbuch

Clarke

Clarke CHT879 Bedienungsanleitung

Clarke

Clarke Contractor CON750 Bedienungsanleitung

Clarke

Clarke Air CAT63 Installations- und Betriebshandbuch

Clarke

Clarke CAT115 Bedienungsanleitung

Clarke

Clarke Strong-Arm CSA50FPB Bedienungsanleitung

Clarke

Clarke SB30 Bedienungsanleitung

Clarke

Clarke CTC150LI Bedienungsanleitung

Clarke

Clarke CRT130 Bedienungsanleitung

Clarke

Clarke CAT82B Handbuch

Clarke

Clarke CPSB200B Bedienungsanleitung

Clarke

Clarke CSA20FBT Bedienungsanleitung

Clarke

Clarke CPSB100 Bedienungsanleitung

Clarke

Clarke Air TPG30PTC Bedienungsanleitung

Clarke

Clarke CAT141 Installations- und Betriebshandbuch

Clarke

Clarke CAT211 Installations- und Betriebshandbuch

Clarke

Clarke METALWORKER CMPS1 Bedienungsanleitung

Clarke

Clarke CMFT300QR Bedienungsanleitung

Clarke

Clarke CSG1C Bedienungsanleitung

Clarke

Clarke CIR18Li Installations- und Betriebshandbuch

Clarke

Clarke CSA10F Handbuch

Clarke

Clarke X-Pro CAT202 Installations- und Betriebshandbuch

Clarke

Clarke Air CAT149 Installations- und Betriebshandbuch

Clarke

Clarke CONTRACTOR CON1450WC Fehlerbehebungshandbuch

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung