Clarke King 35N Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS 0706

PLASMA CUTTERS

Model Nos.

King 35N • King 55

PLASMA CUTTERS

SPECIFICATIONS

King35N King55

Supply Voltage 230V 230V

No. of phases IPH 1PH

Frequency 50/60HZ 50/60 HZ

Max. Input Current (230V) 26A 42A

Max. Input Current (400V) - -

Fuse Rating T20A (230V) T36A (230V)

Cutting Depth - (Steel Class C) 4MM 10MM

No. Current Settings 1 2

Working Air Pressure 5 to 5.5 BAR 5 to 5.5 BAR

Rated Air Delivery 100 L/MIN 105 L/MIN

Protection IP21 IP21

Insulation Clas H H

Weight 30KG 50KG

Dimensions 200x470x360 456x580x710

For wiring diagrams and parts lists, please refer to

the accompanying booklet.

CONTENTS Page

Specifications ................................................................................................ 1

EMC Regulations .......................................................................................... 3

Safety Precautions - General ..................................................................... 5

Additional Safety Precautions for Plasma Cutters ................................... 7

What is Plasma Cutting ................................................................................ 8

Features ......................................................................................................... 8

Air Supply ....................................................................................................... 9

Front Panel Description ............................................................................... 9

Electrical Connections ................................................................................ 11

Installation & Operation .............................................................................. 12

Duty Cycle .................................................................................................... 14

Maintenance ............................................................................................... 15

Troubleshooting ............................................................................................ 16

Thank you for purchasing this CLARKE Plasma Cutter.

Before attempting to operate this machine, please read this leaflet thoroughly

and follow the instructions carefully, in doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to the Plasma Cutter

giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period

of 12 months from the date of purchase. Please keep your receipt as proof

of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product

can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ELECTROMAGNETIC INTERFERENCE (EMC)

Whilst this unit complies with EMC regulations, the user is responsible for installing

and using the welding equipment according to the manufacturers instructions. If

electromagnetic disturbances are detected then it shall be the responsibility of

the user of the welding equipment to resolve the situation. In some cases this

remedial action may be as simple as earthing the welding circuit, see ‘Note’. In

other cases it could involve constructing an electromagnetic screen enclosing

the power source and the work complete with associated input filters. In all cases

electromagnetic disturbances must be reduced to the point where they are no

longer troublesome.

Note - The welding circuit may or may not be earthed for safety reasons. Changing

the earthing arrangements should only be authorised by a person who is

competent to assess whether the changes will increase the risk of injury, e.g. by

allowing parallel welding current return paths which may damage the earth circuits

of other equipment.

1. Assessment of area

Before installing welding equipment the user shall make an assessment of potential

electromagnetic problems in the surrounding area. Avoid using your inverter in

the vicinity of:

a) other supply cables, control cables, signalling and telephone cables;

above, below and adjacent to the welding equipment;

b) radio and television transmitters and receivers;

c) computer and other control equipment;

d) safety critical equipment, e.g. guarding of industrial equipment;

e) pacemakers and hearing aids etc;

f) equipment used for calibration or measurement;

g) other equipment in the environment. The user shall ensure that other

equipment being used in the environment is compatible. This may

require additional protection measures;

It may be possible to avoid the above by changing the time of day that welding

or other activities are to be carried out.

The size of the surrounding area to be considered will depend on the structure of

the building and other activities that are taking place. The surrounding area may

extend beyond the boundaries of the premises.

2. Methods of reducing emissions

2.1 Mains supply

Welding equipment should be connected to the mains supply according to the

manufacturers recommendations. If interference occurs, it may be necessary to

take additional precautions such as filtering of the mains supply. Consideration

should be given to shielding the supply cable of permanently installed welding

equipment, in metallic conduit or equivalent. Shielding should be electrically

continuous throughout its length. The shielding should be connected to the welding

power source so that good electrical contact is maintained between the conduit

and the welding power source enclosure.

2.2 Maintenance of the welding equipment

The welding equipment should be routinely maintained according to the

manufacturers recommendations. All access and service doors and covers should

be closed and properly fastened when the welding equipment is in operation.

The welding equipment should not be modified in any way except for those

changes and adjustments covered in the manufacturers

instructions. In particular, the spark gaps of arc striking and stabilizing devices should

be adjusted and maintained according to the manufacturers recommendations.

2.3 Welding cables

The welding cables should be kept as short as possible and should be positioned

close together, running at or close to the floor level.

2.4 Equipotential bonding

Bonding of all metallic components in the welding installation and adjacent to it

should be considered. However, metallic components bonded to the work piece

will increase the risk that the operator could receive a shock by touching these

metallic components and the electrodes at the same time. The operator should

be insulated from all such bonded metallic components.

2.5 Earthing of the workpiece

Where the workpiece is not bonded to earth for electrical safety, nor connected

to earth because of its size and position, e.g. ships hull or building steelwork, a

connection bonding the workpiece to earth may reduce emissions in some, but

not all instances.

Care should be taken to prevent the earthing of the workpiece increasing the risk

of injury to users, or damage to other electrical equipment.

Where necessary, the connection of the workpiece to earth should be made by

a direct connection to the workpiece, but in some countries where direct

connection is not permitted, the bonding should be achieved by suitable

capacitance, selected according to national regulations.

2.6 Screening and shielding

Selective screening and shielding of other cables and equipment in the surrounding

area may alleviate problems of interference. Screening of the entire welding

installation may be considered for special applications.

SAFETY PRECAUTIONS

WARNING:

As with all machinery, there are certain hazards involved with their operation

and use. Exercising respect and caution will considerably lessen the risk of

personal injury. However, if normal safety precautions are overlooked, or

ignored, personal injury to the operator may result.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY

GENERAL PRECAUTIONS

A) Burn prevention

Wear protective clothing - gauntlet gloves designed for use in welding, hat, and

protective shoes. Button shirt collar and pocket flaps, and wear cuffless trousers to

avoid entry of sparks and slag. Wear helmet with safety goggles or glasses with side

shields underneath, appropriate filter lenses or plates (protected by clear cover

glass). This is a MUST for welding or cutting, (and chipping) to protect the eyes from

radiant energy and flying metal. Replace cover glass when broken, pitted, or

spattered. Avoid oily greasy clothing. A spark may ignite them. Hot metal such as

electrode stubs and workpieces should never be handled without gloves. First aid

facilities and a qualified first aid person should be available for each shift unless

medical facilities are close by for immediate treatment of flash burns of the eyes

and skin burns. Ear plugs should be worn when working overhead or in a confined

space. A hard hat should be worn when others work overhead. Flammable hair

preparations should not be used by persons intending to weld or cut.

B) Toxic fume prevention

Severe discomfort, illness or death can result from fumes, vapours, heat, or oxygen

enrichment or depletion that welding (or cutting) may produce. Prevent them

with adequate ventilation. NEVER ventilate with oxygen. Lead-, cadmium-, zinc-,

mercury- and beryllium-, bearing materials, when welded (or cut) may produce

harmful concentrations of toxic fumes. Adequate local exhaust ventilation must

be used, or each person in the area as well as the operator must wear an air-

supplied respirator. For beryllium, both must be used. Metals coated with or

containing materials that emit toxic fumes should not be heated unless coating is

removed from the work surface, the area is well ventilated, or the operator wears

an air-supplied respirator. Work in a confined space only while it is being ventilated

and, if necessary, while wearing an air-supplied respirator. Vapours from chlorinated

solvents can be decomposed by the heat of the arc (or flame) to form PHOSGENE,

a highly toxic gas, and other lung and eye irritating products. The ultraviolet

(radiant) energy of the arc can also decompose trichloroethylene and

perchloroethylene vapours to form phosgene. DO NOT WELD or cut where solvent

vapours can be drawn into the welding or cutting atmosphere or where the radiant

energy can penetrate to atmospheres containing even minute amounts of

trichloroethylene or perchloroethylene.

C) Fire and explosion prevention

Causes of fire and explosion are:

1) combustibles reached by the arc, flame, flying sparks, hot slag or heated

material;

2) misuse of compressed gases and cylinders;

3) short circuits.

BE AWARE THAT flying sparks or falling slag can pass through cracks, along pipes,

through windows or doors, and through wall or floor openings, out of sight of the

goggled operator. Sparks and slag can fly 10m.

To prevent fires and explosion: keep equipment clean and operable, free of oil,

grease, and (in electrical parts) of metallic particles that can cause short circuits.

If combustibles are in area, do NOT weld or cut. Move the work if practicable, to

an area free of combustibles.

Avoid paint spray rooms, dip tanks, storage areas, ventilators. If the work cannot

be moved, move combustibles at least 10m. away out of reach of sparks and

heat; or protect against ignition with suitable and snug fitting, fire- resistant covers

or shields.

Walls touching combustibles on opposite sides should not be welded on (or cut).

Walls, ceilings, and floor near work should be protected by heat resistant covers

or shields. Fire watcher must be standing by with suitable fire extinguishing

equipment during and for some time after welding or cutting if:

a) appreciable combustibles (including building construction) are within 10m.

b) appreciable combustibles are further than 10m but can be ignited by sparks.

c) openings (concealed or visible) in floors or walls within 10m can expose

combustibles to sparks.

d) combustibles adjacent to walls, ceilings, roofs or metal partitions can be

ignited by radiant or conducted heat.

After work is done, check that area is free of sparks, glowing embers, and flames.

An empty container that held combustibles, or that can produce flammable or

toxic vapours when heated, must never be welded on or cut, unless container

has first been cleaned. This includes

.......a thorough steam or caustic cleaning (or a solvent or water washing,

depending on the combustible’s solubility) followed by purging and inerting with

nitrogen or carbon dioxide, and using protective equipment.

Water filling just below working level may substitute for inerting.

A container with unknown contents should be cleaned (see paragraph above),

do NOT depend on sense of smell or sight to determine if it is safe to weld or cut.

Hollow castings or containers must be vented before welding or cutting - they

can explode.

In explosive atmospheres, never weld or cut where the air may contain flammable

dust, gas, or liquid vapours.

The safety precautions given previously must be strictly adhered to. The following

precautions are additional to, and focus specifically on Plasma Cutters.

ALWAYS have a fire extinguisher handy when operating the cutter.

ALWAYS wear protective clothing - overalls, gloves and sturdy footwear, To

avoid the risk of burns,

ALWAYS ensure that the cutting cable, air compressor hose and electrical

input lead are kept well away from the possible ‘spatter’ of hot metal created

when cutting.

ALWAYS operate the cutter in a well ventilated area or an area equipped

with a fume extractor. Check the possibility that the material to be cut will

give off toxic gas or fumes. If there is any doubt, a respirator should worn.

NEVER operate near water or any other liquid.

NEVER operate near anything flammable. Whilst plasma cutters do not produce

an open flame, they do produce very hot metal during the cutting process, hot

enough to set alight flammable materials, should contact be made.

NEVER observe the electric plasma arc with the naked eye. Always wear

eye protection such as welding goggles used for oxy-acetylene welding.

Should the cutting cable be burned, replace it NEVER attempt to repair it

yourself.

NEVER operate the machine with the covers removed.

NEVER dismantle the tip from the torch unless the machine has been

disconnected from the electrical supply.

NEVER push the torch nozzle down with your hands unless the machine has

been disconnected from the electrical supply.

NEVER cut fuel or lubricant containers, even if they are empty.

NEVER cut containers or casings which contain flammable material.

NEVER cut in environments which are polluted by flammable gas or

combustible vapours, such as petrol etc.

NEVER point the torch jet at people or animals.

Should you feel sick or develop sore eyes whilst using the plasma cutter, STOP

WORK IMMEDIATELY and move to fresh air. Do not resume cutting until you

have provided good ventilation for the cutting area.

When halogenated solvents or degreasing agents are present, the material

to be cut should be cleaned properly to prevent the formation of toxic gases.

Some chlorinated solvents may decompose in the presence of the radiation

given out by the arc and may generate phosphene gas.

ADDITIONAL SAFETY PRECAUTIONS FOR PLASMA CUTTERS

✔

✘

WHAT IS PLASMA CUTTING

Plasma Cutting is a fast, clean and distortion free, means of cutting through all

types of metal from mild and stainless steels to aluminium brass and copper.

The process relies upon the chemical reaction of a gas or mixture of gases, such

as air, when subjected to very high temperatures. The gas ionises, i.e. negative

electrons are separated from the atom, leaving the atom positively charged. In

this ionised state, the gas is electrically conductive and is called ‘plasma’.

A standing electric arc is created to achieve the very high temperature required

to create the plasma. By forcing the plasma through a small nozzle the arc is

constricted and its temperature is increased to over 20,000°C and concentrated

into a very small area.

When the plasma is directed at a conductive material (which is connected to the

earth return lead of the cutter) the arc is transferred through the plasma to the

material. The high energy of the arc melts the material which is displaced by the

gas flow.

The standing arc has to be created by producing an ionised path in the gas. This

is achieved by applying a very high voltage, at high frequency, between the

electrode and the tip/work, causing a high frequency spark. The main arc will

ignite as soon as the gas between the tip and the nozzle is ionised.

The power generator is essentially made up of a transformer, a rectifying unit and

an electronic board.

The latter controls the unit safeguards and governs the work cycles of the various

components which make up the unit, such as the solenoid valve, the HF circuit

(for models fitted with this), the power contactor, etc.

FEATURES

The plasma cutting units are supplied with the following safety devices:

1. Thermal protection devices are installed at the points most subject to high

temperatures such as the power transformers and the rectifying units.

An amber light on the front panel lights up when the thermal protection device

intervenes. See fig.3

2. A pneumatic protection device prevents damage to the torch due to

switching on with either no air supply or low air pressure.

An amber light on the front panel lights up when the pneumatic protection

device intervenes. See fig. 3

3. An Electric shock protection device prevents the operator from coming into

contact with the live parts of the torch (such as the electrode, etc.) This consists

of a safety device, built into the body of the torch, which breaks the main

power circuit when the end part of the torch is removed to replace the

electrode or the tip.

When the electrical protection device intervenes, the unit is prevented from

operating.

MAIN COMPONENTS

The power generator is essentially made up of a transformer, a rectifying unit

and an electronic board.

The latter controls the unit safeguards and governs the work cycles of the various

components which make up the unit, such as the solenoid valve, the power

contactor, etc.

MAIN

CONTACTOR MAIN

TRANSFORMER MAIN

BRIDGE PLASMA

TORCH

CONTROL

PCB

AIR

SOLENOID

VALVE

AIR INPUT

AIR SUPPLY

A compressed air supply is required, capable of delivering clean dry air, at a

minimum pressure of 6 Bar, and at a rate of, from 100 to 210 litres per minute,

depending upon the model. (See Specifications on page 2).

Fig. 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Schweißsystem Handbücher

Clarke

Clarke 195TE Installations- und Betriebshandbuch

Clarke

Clarke AT133 Bedienungsanleitung

Clarke

Clarke CSW6T Installations- und Betriebshandbuch

Clarke

Clarke EASIARC 110 Bedienungsanleitung

Clarke

Clarke MIG102NG Bedienungsanleitung

Clarke

Clarke IMIG100NG Bedienungsanleitung

Clarke

Clarke MIG165TEM Installations- und Betriebshandbuch

Clarke

Clarke EASIARC 200 Handbuch

Clarke

Clarke MMA200 Bedienungsanleitung

Clarke

Clarke MIG85ENB Installations- und Betriebshandbuch

Clarke

Clarke MIG85ENC Installations- und Betriebshandbuch

Clarke

Clarke MIG 152 Bedienungsanleitung

Clarke

Clarke MIG196 Bedienungsanleitung

Clarke

Clarke AT162 Bedienungsanleitung

Clarke

Clarke MIG 150TE Installations- und Betriebshandbuch

Clarke

Clarke Weld MIG 130 TE Turbo Handbuch

Clarke

Clarke MMA200A Bedienungsanleitung

Clarke

Clarke WE6495E Installations- und Betriebshandbuch

Clarke

Clarke MIG106 Bedienungsanleitung

Clarke

Clarke 90EN Installations- und Betriebshandbuch

Clarke

Clarke weld MMA/TIG120 Bedienungsanleitung

Clarke

Clarke Arc/Tig135 Installations- und Betriebshandbuch

Clarke

Clarke Fluxcore/MIG 135sg WE6441 Bedienungsanleitung

Clarke

Clarke AT101 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung