Classe Audio 30 Bedienungsanleitung

CLASSÉ AUDIO

REMOTE CONTROL

BALANCED PREAMPLIFIER

OWNER'S MANUAL

CLASSÉ DESIGN PHILOSOPHY

1. REPEATED LISTENING DESIGN SESSIONS:

Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB boards

etc.), and adjusting many specific operating voltages within proper engineering ranges, producing an

overall sonic recipe giving the most natural harmonic realism of music typical of instruments in a

live performance.

2. UPGRADABLE SINGLE CIRCUIT DESIGNS:

All Classé products (all preamps and all amps) share exactly the same circuit design philosophy

(excluding moving coil and moving magnet phono circuits). This means all amplifiers and all high

level circuits of the preamps benefit from the same design goals. Similar circuits are then tailored to

different power levels etc. Differences between less expensive models and more expensive models

are parts quality and compliment, power supply extravagance and the amount of filtering etc., as

well as features and packaging.

This means that for years Classé has been constantly sonically fine tuning and technically upgrading

this circuit design and its application, thus reaching a very high level of natural musical enjoyment,

as well as excellent reliability which benefits all models - least expensive, most expensive, preamps

and amplifiers alike.

3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS:

Choosing the best attainable quality parts and materials combined with the advantages of the two

above-mentioned areas provides Classé owners with years of proven trouble free reliability and

musical enjoyment.

OWNER'S MANUAL

TABLE OF CONTENTS

UNPACKING & SET-UP................................................... 4

A.C. LINE POWER............................................................. 5

INPUTS................................................................................ 6

OUTPUTS ........................................................................... 8

FRONT PANEL CONTROLS............................................ 9

WARRANTY ..................................................................... 11

FEATURES AND SPECIFICATIONS............................. 13

WARRANTY REGISTRATION....................................... 14

UNPACKING & SET-UP

Your CLASSÉ 30 preamplifier has been carefully wrapped in heavy gauge plastic, packed in

semi-rigid foam and contained in a special box. To remove the unit, open and spread the top flaps of the

box. By its sides, lift out the entire unit with foam pieces intact. Remove each foam side by pulling

straight out. Remove the plastic wrap and inspect the unit for any concealed damage. Apart from this

owner's manual, please ensure the following has also been included:

1) DETACHABLE LINECORD.

2) ALLEN KEY FOR TOP COVER.

3) RESISTOR KIT FOR MOVING COIL GAIN ADJUSTMENT

4) REMOTE CONTROL UNIT (Allen key and Batteries: AAA X 2 included).

Please report any damage or missing parts to your dealer promptly.

This preamplifier, being capable of very high gain, must be located in a position free of any

hum-inducing magnetic fields. (This also applies to turntables and interconnect cables.) Positions

adjacent to power amplifiers, A.C line filters, or regulation devices should be avoided. Ideally, a few feet

should separate the preamplifier from the power amplifier. As well, keep low-level interconnect cables

away from the power amp and separate from A.C. line cords.

Heat generated by the preamplifier is negligible. Air space around the unit need not be a

concern.

Check the Serial Number sticker on the back of the unit for the correct operating voltage.

Regardless of voltage, the internal fuse rating should be 1 AMP SLO-BLO.

A.C. LINE POWER

The Classé 30 preamplifier has no power switch. Its low power consumption and improved

sonics from always being ON led to the omission of an ON/OFF switch. In fact, while thoroughly

musical shortly after turn-on, the preamplifier will exhibit "sonic growth" during its first 300 hours of

use.

For optimum sonic performance, you should consider the use of the optional CLASSÉ REFERENCE

A.C. LINECORD. Consult your dealer regarding this accessory.

SAFETY FEATURE:

The 30 preamplifier is designed with an auto-muting circuit which engages and is indicated by a

FLASHING GREEN LED when the unit is first connected, or after an AC power failure. After 15

seconds the STEADY GREEN LED signals that the unit is in STANDBY mode (Note: MUTE is ON

during STANDBY mode).

This feature will prevent any turn-on surges or unstable output from reaching the power

amplifier and possibly the loudspeakers. Similarly, make sure the MUTE is ON (STEADY GREEN)

again when removing A.C. line power.

CAUTION:

DISCONNECT AC LINE CABLE WHILE MAKING ALL CONNECTIONS. "FLOATING THE GROUND”

OR DEFEATING THE GROUND ON A 3-PRONG LINECORD MAY CREATE A SHOCK HAZARD. CONNECT

ALL INTERCONNECT CABLES BETWEEN THE ELECTRONICS BEFORE CONNECTING THE A.C.

LINECORDS TO THE WALL OUTLETS. THIS WILL REDUCE THE POTENTIAL SHOCK HAZARD. SEE ALSO

THE WARRANTY SECTION OF THIS OWNER'S MANUAL.

INPUTS:

The input jacks are clearly marked on the back of the 30. The following inputs are provided:

PHONO/AUX, VIDEO, CD, TUNER, BALANCED, and TAPE.

PHONO/AUX

The 30 preamplifier can be configured as a PHONO or LINE unit by setting the internal

jumpers. The PHONO and AUX share the same pair of RCA input jacks. The following steps should

be performed to switch between them.

1) Make sure MUTE is ON (Steady GREEN)

2) Disconnect A.C. line cord from the wall outlet.

3) Remove the top cover with the Allen key supplied.

4) Locate PHONO/AUX Input and Output jumpers. Switch to desired type of input.

PHONO INPUT:

When switched to PHONO the input can accommodate both magnetic and moving coil

cartridges of varying output levels. Set the jumpers to MM for magnetic or MC for a moving coil

cartridge. In the MC position, gain of the Moving Coil stage is factory preset at 23dB which matches

perfectly with most typical MC cartridges. With the resistor kit (included), the gain can be adjusted

from 13dB to 41dB, in order to optimize system gain, and low noise while using other less typical

MC cartridges. (Note: The MC gain is in addition to the standard MM gain of 38dB). To change the

MC gain, proceed as follows:

1) Make sure MUTE is ON (Steady GREEN)

2) Disconnect A.C. line cord from the wall outlet.

3) Remove the top cover with the Allen key supplied.

4) Locate R104 and R204, which are the MC gain setting resistors for the LEFT and RIGHT

channels respectively. Remove the resistors and replace them with newly selected ones, according to

the following chart:

GAIN COLOR CODED RESISTOR (or) NUMERICAL RESISTOR

13 dB (Brown,Red,Purple,Brown,Brown) 1271

23 dB (standard) (Yellow,White,White,Brown,Brown) 4991

29 dB (Brown,Black,Black,Red,Brown) 1002

35 dB (Red,Black,Black,Red,Brown) 2002

41 dB (Yellow,Purple,Green,Red,Brown) 4752

Silver solder is provided in the kit for this purpose. The resistor kit is for setting the MC gain which

will optimize output levels, noise, and efficiencies of less typical cartridges.

5) Having completed the resistor changes, replace the top cover.

AUX INPUT:

When selected, the AUX input serves as an additional high level input, accommodating

additional sources such as VIDEO, CD, TUNER, etc...

VIDEO, CD, TUNER:

These are all high level inputs sharing exactly the same characteristics, and may be

interchanged if so desired.

BALANCED

The BALANCED INPUT is a true differential high level input, wired as follows:

PIN 1: GROUND

PIN 2: POSITIVE (NON-INVERTED) SIGNAL

PIN 3: NEGATIVE (INVERTED) SIGNAL

It may be used with CD players that have a balanced output, or any other high level balanced

sources.

TAPE IN

The TAPE IN of the 30 preamplifier should be connected to the LINE OUT or TAPE OUT

of the tape deck. The TAPE input does not appear on the selector switch. It is activated by the TAPE

switch. (See FRONT PANEL CONTROLS: TAPE SWITCH.)

OUTPUTS

The Classé 30 preamplifier has both regular (single-ended) and balanced outputs. Both are

working at all times, and may be used separately, or simultaneously.

TAPE OUTPUT

Whatever input is selected by the INPUT SELECTOR will be fed to the TAPE OUTPUT

jacks. This should be connected to the TAPE IN or LINE IN of the tape deck.

REGULAR OUTPUTS

Simply connect your regular interconnects to the RCA output jacks marks REGULAR

OUTPUT on the back of the 30.

BALANCED OUTPUTS

A balanced power amplifier and balanced interconnects are also required. For use with a

balanced power amplifier other than Classé, the wiring of the 3-pin XLR connectors must be wired

as follows:

PIN 1: GROUND

PIN 2: POSITIVE (NON-INVERTED) SIGNAL

PIN 3: NEGATIVE (INVERTED) SIGNAL

If the pin configuration of the power amplifier differs from above, the balanced interconnects

must be modified to accommodate the different power amp.

Having confirmed the correct connections, plug the XLR connectors of the balanced

interconnects into the locking XLR connector on the rear of the 30 marked BALANCED OUTPUT.

(To remove the connectors, press the tab above the connector.)

FRONT PANEL CONTROLS

INPUT SELECTOR:

This selects one of the five inputs connected to the preamplifier, except TAPE IN (see TAPE

SWITCH below). The selector switch is silent and will prevent pulses when switching positions.

However, it remains good practice to reduce the volume control level or put MUTE to ON (steady

GREEN LED) when changing the input selection.

TAPE SWITCH:

In the SOURCE position, the preamp will process the signal as chosen by the INPUT

SELECTOR. In the TAPE position, the preamp will process the TAPE INPUT signal, overriding the

INPUT SELECTOR.

BALANCE CONTROL:

The custom balance control permits equal output of each channel in the center (detented)

position without additional loading to the signal. When shifted to the left or right, it merely

attenuates the opposite channel.

VOLUME CONTROL: (remote control)

The VOLUME CONTROL varies the output level of both channels simultaneously. It can be

operated from remote using the hand held control unit or manually turning the control knob at the

preamp.

PLAY/MUTE SWITCH: (remote control)

Switching between PLAY and MUTE can be done by either manually pressing the

PLAY/MUTE switch down momentarily on the 30 faceplate or pushing the MUTE button on the

hand held remote control unit. The PLAY (or MUTE OFF) and MUTE ON selections are indicated

by the STEADY RED or GREEN LED respectively at the preamp.

When MUTE (ON) is selected, which is indicated by a STEADY GREEN LED, the outputs

of the preamplifier are completely cut off. In the PLAY (MUTE OFF) selection, which is indicated

by a STEADY RED LED, the signal is allowed to pass to the power amplifier.

NOTE: WHEN THE 30 IS IN THE MUTE POSITION, AND THE VOLUME CONTROL

IS TURNED UP USING THE REMOTE CONTROL UNIT, THE PLAY MODE IS

AUTOMATICALLY SELECTED.

CAUTION: Make sure the preamp is in MUTE (ON) when making or changing any connections.

This includes all inputs and outputs, as well as A.C. line cord.

Inhaltsverzeichnis

Andere Classe Audio Verstärker Handbücher

Classe Audio

Classe Audio DR-10 Bedienungsanleitung

Classe Audio

Classe Audio CA-2200 Bedienungsanleitung

Classe Audio

Classe Audio CP-700 - V1.8 Bedienungsanleitung

Classe Audio

Classe Audio CA-M600 Bedienungsanleitung

Classe Audio

Classe Audio CT-5300 - V1.2 Bedienungsanleitung

Classe Audio

Classe Audio Omega Series Bedienungsanleitung

Classe Audio

Classe Audio CP-500 Bedienungsanleitung

Classe Audio

Classe Audio CAP-2100 Bedienungsanleitung

Classe Audio

Classe Audio OMEGA-MONO-V2 Bedienungsanleitung

Classe Audio

Classe Audio SSP-30 MKII Bedienungsanleitung

Classe Audio

Classe Audio CA-5200 Bedienungsanleitung

Classe Audio

Classe Audio CA-3200 Bedienungsanleitung

Classe Audio

Classe Audio CAM-200 Bedienungsanleitung

Classe Audio

Classe Audio Delta PRE Bedienungsanleitung

Classe Audio

Classe Audio CA-M300 Bedienungsanleitung

Classe Audio

Classe Audio CA-M300 Bedienungsanleitung

Classe Audio

Classe Audio CA-5300 - V1.4 Bedienungsanleitung

Classe Audio

Classe Audio CAP-2100 Bedienungsanleitung

Classe Audio

Classe Audio Classe Audio Bedienungsanleitung

Classe Audio

Classe Audio CA-2100 Bedienungsanleitung

Classe Audio

Classe Audio CAM-200 Bedienungsanleitung

Classe Audio

Classe Audio DR-10 Bedienungsanleitung

Classe Audio

Classe Audio CA-101 Bedienungsanleitung

Classe Audio

Classe Audio CA-3200 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung