Clearaudio Statement Bedienungsanleitung

Statement

Clearaudio electronic®GmbH

Spardorfer Str. 150 • D-91054 Erlangen • Tel. +49 9131 40300100 • FAX + 49 9131 40300119

www.clearaudio.de • www.analogshop.de • info@clearaudio.de

©Clearaudio electronic GmbH

Version: 1.3_10.01.2017_E

User manual

Made in Germany

Dear Clearaudio customer,

Congratulations on your purchase of the

Statement

turntable.

You have purchased a state-of-the-art turntable, the

Statement

, a world class product from

Clearaudio electronic GmbH.

The special resonance-optimised construction, the external motor-unit and the patented Clearaudio -

CMB

-bearing-technology guarantees absolute speed stability, pure pleasure in listening and reproduction

absolutely faithful to the original.

Thank you very much your condence.

Please read this user manual carefully to ensure that your

Statement

turntable is correctly installed ready

to take you to a new dimension of music reproduction.

We hope you will enjoy your new Clearaudio

Statement

turntable.

Clearaudio electronic GmbH

Please read the warning before connecting your

Statement

turntable to the mains supply.

Statement

User manual

WARNINGS

Don’t expose your turntable to rain or humidity.

Don’t handle the mains leads with wet hands.

Don’t place or insert anything into the equipment or through ventilation holes.

No naked ame sources, such as lighted candles, should be placed on the equipment.

CE-MARKING

Recording und reproduction of any sound-material may require the consent of the creator.

Please acknowledge the information given in the

- Copyright Act 1956,

- Dramatic and Musical Performers Act 1958,

- Performers Protection Acts 1963 and 1972,

- Any more recent legal regulations.

Page 2 © Clearaudio electronic GmbH 2017

The Clearaudio

Statement

meets the regulations concerning electromagnetic

disturbance (EMC) and low-voltage appliances.

Contents

1. Packaging overview 4 - 5

2. Construction overview 6

3. Setup and operation 7 - 15

4. Motor adjustment 16

5. Special notes 17

6. Technical data 18

Warranty information 19

Page 3© Clearaudio electronic GmbH 2017

Statement

User manual

1. Packaging overview

The

Statement

turntable is packed and delivered on either a Euro pallet or two half size Euro pallets. The

Packing is specially made for the

Statement

turntable and should be retained for any repacking.

Please note:

The

Statement

turntable is very heavy and will require at least two people to unpack and setup.

Attention / Warning:

IMPORTANT!

Before it is fully assembled there are strong magnetic elds around the main bearing, these

could interfere with heart pacemakers and so the Statement should not be setup by anyone

with a pacemaker.

The Statement turntable is extremely heavy and should not be assembled by anyone with

back problems.

The two wooden boxes contain the turntable stand and the pendulum weights, as well as ve (5)

separately packed cartons containing all other parts (e.g. massive metal cross, acrylic chassis, bearings

etc).

Please check the accessories contents according to the following list before you setup the turntable.

Page 4 © Clearaudio electronic GmbH 2017

Statement

User manual

1. Two pairs of white gloves 5. Three bases as counter weights (40mm)

2. Two belts 6. Four bases as at pads

3. Tool for adjustment of stainless steel discs

(pendulum weight) 7. Polishing paste

4. Three bases as counter weights (20mm) 8. A set of hex wrenches

432

Page 5© Clearaudio electronic GmbH 2017

Statement

User manual

1312

11109

9. Bearing oil 13. Bubble level gauges

10. Acrylic cleaner 14. Not shown: Two wooden blocks

11. Screwdriver 15. Not shown: User manual

12. Statement clamp 16. Not shown: Warranty card, Clearaudio

certicate card (QCQ)

Page 6 © Clearaudio electronic GmbH 2017

Statement

User manual

2. Construction overview

Pic. 1: Construction overview

Page 7© Clearaudio electronic GmbH 2017

Statement

User manual

3. Set up and operation

Select the position in which you will uste the

Statement

turntable. Place the

Statement

turntable base in this position

on the four supplied feet.

Place the two wooden blocks beneath the

Statement

base as

shown.

Pic. 2: Placing the

Statement

Pic. 3: Placing the

Statement

Page 8 © Clearaudio electronic GmbH 2017

IMPORTANT!

Being careful not to damage the bearing spindle on top of the pendulum shaft, assemble the pendulum,

starting by sliding a solid metal disc over the pendulum shaft so that it rests on the wooden blocks.

Be sure to place a felt mat between each metal disc, building the pendulum with three solid discs at the

bottom, then six half-cut-away discs, then two more solid discs, nally adding the solid disc engraved with

the words Clearaudio

Statement

User manual

Pic. 4: Placing the discs

Disc engraved with

„Clearaudio

Statement

“

Disc, solid

(2 pcs.)

Disc, half cut away

(6 pcs.)

Disc, solid

(3 pcs.)

Place a felt mat in

between each stainless

steel platters

Please note:

If you are using the

Statement TT1

tangential tonearm, position the half-cut-away discs with the cut-away

section at the rear of the turntable.

Place the four cork damping plates on top of the four corner pillars.

Place 4 pcs. damping

plates if not assembled

already from the factory

Please note:

Again, being careful not to damage the bearing spindle on top

of the pendulum shaft, lower the stainless steel cross frame over

the pendulum shaft so that is rests on the four cork damping

plates.

Pic. 5: Placing the cork damping plates

Page 9© Clearaudio electronic GmbH 2017

Statement

User manual

Set the cross shaped massive metal part through the spindle onto the four cork

Tighten the bearing to the shaft by tightening the screws in the bearing collar (8x).

Pic. 6: Placing the metal part Pic. 6.1: Placing the metal part

Pic. 7: Tighten the bearing

Page 10 © Clearaudio electronic GmbH 2017

Statement

User manual

Lift the pendulum shaft to align the V-shaped groove in the pendulum shaft with the locking screws in the

gimbal bearing. Lock the gimbal bearing to the pendulum shaft by fully tightening the eight screws so that

they locate in the groove of the pendulum shaft.

Pic. 9: Removing the wood spacers

IMPORTANT!

Carefully lift the whole upper section, raising the

pendulum off of the wooden blocks.

Pic. 8: Lifting the upper part

Remove the wooden blocks from beneath the

turntable and carefully lower the upper section back

onto the four cork damping plates.

Andere Handbücher für Statement

Inhaltsverzeichnis

Andere Clearaudio Drehscheibe Handbücher

Clearaudio

Clearaudio concept Signature Bedienungsanleitung

Clearaudio

Clearaudio Statement V2 Bedienungsanleitung

Clearaudio

Clearaudio Turbo Weight Bedienungsanleitung

Clearaudio

Clearaudio Performance DC Bedienungsanleitung

Clearaudio

Clearaudio Concept Bedienungsanleitung

Clearaudio

Clearaudio Satisfy Bedienungsanleitung

Clearaudio

Clearaudio Concept Bedienungsanleitung

Clearaudio

Clearaudio Stroboscope Testrecord Bedienungsanleitung

Clearaudio

Clearaudio Champion Bedienungsanleitung

Clearaudio

Clearaudio Champion Handbuch

Clearaudio

Clearaudio Master Innovation Bedienungsanleitung

Clearaudio

Clearaudio Concept Bedienungsanleitung

Clearaudio

Clearaudio Performance DC Bedienungsanleitung

Clearaudio

Clearaudio Concept MC Technisches Handbuch

Clearaudio

Clearaudio Performance DC Bedienungsanleitung

Clearaudio

Clearaudio Turbo Weight Bedienungsanleitung

Clearaudio

Clearaudio Statement TT1 Bedienungsanleitung

Clearaudio

Clearaudio Concept Bedienungsanleitung

Clearaudio

Clearaudio Clarify Bedienungsanleitung

Clearaudio

Clearaudio Moving Coil V2 Bedienungsanleitung

Clearaudio

Clearaudio Emotion SE Bedienungsanleitung

Clearaudio

Clearaudio Ambient Bedienungsanleitung

Clearaudio

Clearaudio Jubilee MM Bedienungsanleitung

Clearaudio

Clearaudio Peerformance Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

Reloop

Reloop SMP-1 Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung