Clifford Matrix 1 Bedienungsanleitung

MMaattrriixx11

IInnssttaallllaattiioonnGGuuiiddee

Directed Electronics, Inc. N909429 07-05

Bitwriter

, Code Hopping

, Directed

, Doubleguard

, ESP

, FailSafe

, Ghost Switch

, Learn

Routine

™

, Nite-Lite

, Nuisance Prevention

Circuitry, Revenger

, NPC

, Silent Mode

™

, Soft

Chirp

, Stinger

, Valet

, VRS

, and Warn Away

are all Trademarks or Registered Trademarks of

Directed Electronics, Vista, California.

The Bitwriter®(p/n 998T)

requires chip version 2.2 or

newer to program this unit.

www.clifford.com

Table of Contents

WWhhaattIIssIInncclluuddeedd....................................................................................................................................................................................................................................................44

PPrriimmaarryyHHaarrnneessss((HH11))WWiirreeCCoonnnneeccttiioonnGGuuiiddee...................................

.....................................................................................................................44

Primary Harness Wiring Diagram.............................................................................................4

Primary Harness Wiring Instructions........................................................................................4

DDoooorrLLoocckkHHaarrnneessss((HH22)),,33--PPIINNCCoonnnneecctto

orr............................................................................................................................................................1100

PPeerriipphheerraallPPlluugg--IIn

nHHaarrnneesssseess..............................................................................................................................................................................................................1100

Super Bright LED, 2-Pin WHITE Plug..................................................................................10

Valet/Program Switch, 2-Pin BLUE Plug ................................................................................11

Programmer Interface, 3-Pin BLACK Plug .............................................................................11

Mounting the Receiver/Antenna .............................................................................................12

OOnn--BBooaarrddDDuuaall--SSttaaggeeSShhoocckkSSeennssoorr...................................................................................................

...................................................................................1133

OOppttiioonnaallSSeennssoorrPPoorrtt,,44--ppiinnCCoonnnneeccttoorr.....................................

.......................................................................................................................................1133

PPrrooggrraammmmiinnggJJuummppeerr.......................

...........................................................................................................................................................................................................1144

Light Flash Jumper..................................................................................................................14

BByyppaassssiinnggSSeennssoorrIInnppuuttss.............................................................................................................................................

...............................................................................1144

SSyysstteemmFFeeaattuurreessLLeeaarrnnRRoouuttiinnee.........................................................

.............................................................................................................................................1155

SSyysstteemmFFeeaattuurreessMMeennuuss...........

Menu #1 - Basic Features........................................................................................................18

Menu #2 - Advanced Features.................................................................................................18

FFeeaattuurreeDDeessccrriippttiioonnss.........................................................................................................................................

.............................................................................................1199

Menu #1 - Basic Features........................................................................................................19

TTrraannssmmiitttteerr//RReecceeiivveerrLLeeaarrnnRRoouuttiinnee.............................

.........................................................................................................................................................2222

TTrraannssmmiitttteerrCCoonnffiigguurra

attiioonnss..................................................................................................................................................................................................................2244

3-Button Transmitter Configuration .......................................................................................24

4-Button Transmitter Configuration .......................................................................................25

Optional Radar Master Transmitter ........................................................................................25

DDiiaaggnnoossttiiccss...................................................................................................................................................

...............................................................................................................2255

Arm/Disarm Diagnostics.........................................................................................................25

System Status Chirps...............................................................................................................26

Table of Zones ........................................................................................................................26

LLoonnggTTeerrmmEEvveennttHHiissttoorryy.........................

.............................................................................................................................................................................................2266

MMuul

lttii--LLeevveellSSeeccuurriittyyAArrmmiinngg..............................................................................................................................................................................................................2277

OOppttiioonnaallVVeehhiicclleeRReeccoovveerryySSyysstteemm((VVRRSS))...............................................................

.......................................................................................................2288

FFaallsseeAAllaarrmmCCoonnttrroollTTeecchhnnoollooggyy((FFAACCTT)).................

.....................................................................................................................................................2288

SSmmaarrttPPoowweerrUUppIIII...........

WWiirriinnggQQuuiicckkRReeffeerreenncceeGGuuiiddee.................................................................................................................

.....................................................................................3300

2005

What Is Included

Primary Harness (H1) Wire Connection Guide

Primary Harness Wiring Diagram

___

Primary Harness Wiring Instructions

This guide describes in detail the connection of each wire. Also included are possible applications

of each wire. This system was designed with the ultimate in flexibility and security in mind. Many

of the wires have more than one possible function. Please read carefully to ensure a thorough under-

standing of this unit.

RED/WHITE (-) 200 mA Channel 2 Output

RED (+) Constant Power Input

BROWN (+) Siren Output

YELLOW (+) Switched Ignition Input, Zone 5

BLACK (-) Chassis Ground Input

VIOLET (+) Door Trigger Input, Zone 3

BLUE (-) Instant Trigger Input, Zone 1

GREEN (-) Door Trigger Input, Zone 3

BLACK/WHITE (-) 200 mA Domelight Supervision Output

WHITE/BLUE (-) 200 mA Channel 3 Programmable Output

WHITE (+)/(-) Selectable Light Flash Output

ORANGE (-) 500 mA Armed Output

H1/1

H1/2

H1/3

H1/4

H1/5

H1/6

H1/7

H1/8

H1/9

H1/10

H1/11

H1/12

➤➤One control module with on-board shock

sensor

➤➤One HF+ receiver/antenna with harness

➤➤Two three-button remote transmitters

➤➤One 514C siren

➤➤One 12-pin primary harness with starter kill

➤➤One plug-in Valet/Program switch

➤➤One plug-in LED indicator with bezel

➤➤One 3-pin door lock harness

➤➤Two window decals

➤➤One patent card

➤➤One warranty registration

➤➤One installation guide

➤➤One owner’s guide

www.clifford.com

H1/1 ORANGE (-) ground-when-armed output

This wire supplies a (-) ground as long as the system is armed. This output ceases as soon as the

system is disarmed. The orange wire is pre-wired to control the 8618 starter kill relay. It can supply

up to 500 mA of current.

NOTE: If using the H1/1 ORANGE wire to activate an add-on accessory such as window

automation, pager or voice module a 1Amp diode must be installed to ensure proper operation.

Insert the diode as shown in the following diagram.

H1/2 WHITE (+/-) light flash output

As shipped, the H1/2 WHITE wire should be connected to the (+) parking light wire. If the light flash

polarity jumper is moved to the (-) position (see the

Programming Jumper

section of this installation

guide), this wire supplies a (-) 200 mA output. This is suitable for driving (-) light control wires in

Toyota, Lexus, BMW, some Mitsubishi, some Mazda, and other models.

NOTE: For parking light systems that draw 10 amps or more, the jumper must be switched to a

(-) light flash output (see the

Programming Jumpers

section of this guide). P/N 8617 or a standard

automotive SPDT relay must be used on the H1/2 light flash output wire.

IMPORTANT! Never interrupt any wire other than the starter wire.

2005

H1/3 WHITE/BLUE 200 mA (-) channel 3 output

This wire provides a (-) 200 mA output whenever the transmitter button(s) controlling channel

three is pressed. This output can be programmed to provide the following types of output (see

System Features Learn Routine

section of this guide):

➤➤A vvaalliiddiittyyoutput will send a signal as long as the transmission is received.

➤➤A llaattcchheeddoutput will send a signal continuously when the channel three button(s) is pressed and

released. The signal will continue until channel three is pressed again.

➤➤A llaattcchheedd//rreesseettwwiitthhiiggnniittiioonnoutput works similar to the latched output, but will also reset

(output will stop) when the ignition is turned on and then off.

➤➤A 3300sseeccoonnddttiimmeeddoutput will send a signal for 30 seconds when channel three is pressed. This

output can be shut off during the 30-second period by pressing Channel 3 again.

➤➤This output can also be programmed to provide a sseeccoonndduunnlloocckkppuullsseewhen the unlock button

is pressed a second time after disarming the system. This can be used to unlock the passenger

doors when installing progressive door locks.

IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!

This transistorized output can only supply 200 mA, and connecting directly to a

solenoid, motor, or other high-current device will cause the module to fail.

IMPORTANT! DO NOT connect this wire to a negative vehicle light flash wire before

changing the programming jumper to the negative polarity position or damage to

vehicle light circuit may occur.

www.clifford.com

H1/4 BLACK/WHITE (-) 200 mA domelight supervision output

Connect the H1/4 wire to the optional domelight supervision relay as shown in the following

diagram:

H1/5 GREEN (-) door trigger input

Most vehicles use negative door trigger circuits. Connect the green wire to a wire showing ground

when any door is opened. When connecting to newer model vehicles there is generally a need to use

individual door triggers. See DirectFax document 1076 for wiring instructions. This wire will report

Zone 3.

NOTE: If using a door trigger wire that has a delay, Advanced Menu 2, feature 6 or the 998T

Bitwriter can be used to turn Bypass Notification off.

H1/6 BLUE (-) instant trigger input

This input will respond to a negative input with an instant trigger. It is ideal for hood and trunk pins

and will report on Zone 1. It can also be used with Directed single-stage sensors. The H1/6 blue

instant trigger wire can also be used to shunt sensors during operation of auxiliary channels or remote

start. (See

Bypassing Sensor Inputs

section of this guide.)

IMPORTANT! This output is only intended to drive a relay. It cannot be connected

directly to the domelight circuit, as the output cannot support the current draw of one

or more bulbs.

2005

H1/7 VIOLET (+) door trigger input

This type of dome circuit is used in many Ford products. Connect the violet wire to a wire that shows

(+)12V when any door is opened. This wire will report Zone 3.

NOTE: If using a door trigger wire that has a delay, Advanced Menu 2, feature 6 or the 998T

Bitwriter can be used to turn Bypass Notification off.

H1/8 BLACK (-) chassis ground connection

Connect this wire to a clean, paint-free sheet metal location (driver kick panel) using a factory bolt

that DOES NOT have any vehicle component grounds attached to it. A screw should only be used

when in conjunction with a two-sided lock washer. Under dash brackets and door sheet metal are

not acceptable ground points. It is recommended that all security components be grounded at the

same location.

H1/9 YELLOW (+) ignition input

Connect this wire to the (+) 12 volts ignition wire. This wire is pre-wired to the starter kill relay and

must show (+) 12 volts with the key in RUN position and during cranking. Take great care that this

wire cannot be shorted to the chassis at any point.

www.clifford.com

H1/10 BROWN (+) siren output

Connect this to the RED wire of the Revenger

siren. Connect the BLACK wire of the siren to (-)

chassis ground, preferably at the same point you connect the control module’s BLACK ground wire.

H1/11 RED (+)12V constant power input

Before connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or

the constant 12V supply to the ignition switch.

NOTE: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the 15 amp

fuse in the harness for this purpose. This fuse protects the module itself.

H1/12 RED/WHITE 200 mA (-) channel 2 output

When the system receives the code controlling channel 2 for longer than 1.5 seconds, the

RED/WHITE will supply an output as long as the transmission continues. This is often used to

operate a trunk/hatch release or other relay/driven function.

IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!

The transistorized output can only supply 200 mA of current. Connecting directly to a

solenoid, motor, or other high-current device will cause it to fail.

2005

Door Lock Harness (H2), 3-PIN Connector

___

NOTE: For detailed instructions about connecting to the vehicle’s power door lock systems, refer

to the Door Lock Wiring guide (Document No. 1041) available to authorized dealers only from the

technical resources listed at the front of this guide.

Peripheral Plug-In Harnesses

Super Bright LED, 2-Pin WHITE Plug

The super bright LED operates at (+) 2 volt DC and plugs into the two-pin WHITE port. Make

sure the LED wires are not shorted to ground as the LED will be damaged. Multiple LED’s can be

used, but they must be wired in series. The LED fits into a 9/32-inch mounting hole. Be sure to

check for clearance prior to drilling the mounting hole.

NOTE: Never use a BLUE LED in combination with a RED LED.

IMPORTANT! The door lock outputs are low current and should not be attached

directly to any high current device; they are only to be used to activate relays

Blue (-) Unlock, (+) Lock Output

Empty Unless Using 451M

Green (-) Lock, (+) Unlock Output

H2/A

H2/B

H2/C

Andere Handbücher für Matrix 1

Inhaltsverzeichnis

Andere Clifford Autoalarmanlage Handbücher

Clifford

Clifford AVANTGUARD 5 Bedienungsanleitung

Clifford

Clifford Bullet 4 Bedienungsanleitung

Clifford

Clifford BlackJax 5 Bedienungsanleitung

Clifford

Clifford SmartWindows 4 Bedienungsanleitung

Clifford

Clifford 30 Bedienungsanleitung

Clifford

Clifford RSX3.2 Bedienungsanleitung

Clifford

Clifford intelliguard 700-IQ Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Clifford

Clifford SE 5000 Bedienungsanleitung

Clifford

Clifford AvantGuard 2 Bedienungsanleitung

Clifford

Clifford intelliguard 900-IQ Bedienungsanleitung

Clifford

Clifford AvantGuard 3 Bedienungsanleitung

Clifford

Clifford Responder LC3 4706X Bedienungsanleitung

Clifford

Clifford Concept 650MkII Bedienungsanleitung

Clifford

Clifford 3105X Bedienungsanleitung

Clifford

Clifford 300UK Betriebsanleitung

Clifford

Clifford Sabre Bedienungsanleitung

Clifford

Clifford 22CX Bedienungsanleitung

Clifford

Clifford 4706X Responder LC3 Bedienungsanleitung

Clifford

Clifford 5706X Bedienungsanleitung

Clifford

Clifford ACE 2000 Bedienungsanleitung

Clifford

Clifford Cyber 4 Bedienungsanleitung

Clifford

Clifford Model RSX1.2 Bedienungsanleitung

Clifford

Clifford Matrix 10.2X Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung