Code Alarm Ca2LED5E Bedienungsanleitung

PROFESSIONAL

SERIES

Owner’s Guide

For Models:

caSECRS

ca2LED5

ca2LED5E

IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is

applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR

SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.

Deluxe Vehicle Security and

Remote Start System

2caSECRS ca2LED5 4280831 Owners revB

Table of Contents

Using Your Remote Control.................................................................... 3

Arming the Security System .............................................................. 3

Passive Arming Bypass..................................................................... 3

Bypassing the Shock Sensor ............................................................ 3

Hidden Alarm Function...................................................................... 3

Disarming the Security System ......................................................... 3

Two Stage Door Unlock (optional)..................................................... 4

Activating Trunk Release (optional)................................................... 4

Activating AUX 1 (optional)................................................................ 4

Entering AUX Mode and Activating Additional AUX Outputs............. 4

Using the Progressive Car Finder Feature........................................ 5

Using the Personal Protection Alarm................................................. 5

Programmed Transmitter Notication................................................ 5

Valet Mode ........................................................................................ 5

User Selectable Notication Chirps................................................... 5

User Selectable LED ......................................................................... 6

Manually Overriding the Security System ......................................... 6

Carjack Mode .................................................................................... 6

Using Your Remote Vehicle Starter ....................................................... 7

Remote Start Ready Mode................................................................ 7

Cancelling Remote Start Ready Mode .............................................. 7

Remote Starting Your Vehicle............................................................ 8

Remote Start Shutdown .................................................................... 8

Entering Your Vehicle while it is Running via Remote Start .............. 8

Enter & Exiting the Vehicle - Remote Start Ready Mode .................. 8

Using the “Quick-Stop” Feature......................................................... 9

Preheating or Precooling the Vehicle’s Interior ............................... 10

User Programmable Run Time / Run Time Extension..................... 10

Turbo Timer Mode (optional) ........................................................... 10

Operating the 2 / 3 Hour Start Up Timer Mode................................ 11

Operating the Daily Start Timer ....................................................... 12

Temperature Start Mode.................................................................. 12

Remote Start Safety Features......................................................... 12

Status LED, Light Flashes and Siren/Horn Indications ..................... 13

 Additional2-WayLEDRemoteControlNotications ........................ 14

Remote Control Buttons & Functions ................................................. 15

Replacing Remote Control Batteries................................................... 16

Warranty Information ............................................................................ 17

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press the button. The

parking lights will ash 2 times, indicating the system is armed, has locked the doors

(if equipped and connected) and activated the starter disable feature. The LED status

indicator will blink steadily, once per second.

NOTE: The system is equipped with a feature called Silent Choice. If enabled, the

system requires a second press of the button to activate an audible arming

response from the vehicle.

Passive Arming Bypass

If passive arming is enabled on your system, while the system is disarmed, press

+ , the system will respond with 1 chirp and the LED will turn on. The security

system will remain in this temporally bypassed state for as long as you wish. To exit

passive bypass, press the or button and the system will return to normal status.

Bypassing The Shock Sensor

To arm the system and ignore the shock sensor press button, then within 5

seconds press + , the system will respond with 1 long chirp.

NOTE: The system will only change the shock sensor setting for one arm cycle and

will be defaulted back to normal operation the next time the system is armed.

Hidden Alarm Function

Press the button rst, within 3 seconds press the button to activate the hidden

alarm function. The security system will arm with “Hidden Alarm Function” in which the

siren / horn will be silenced if the system is triggered.

Disarming the Security System

To disarm the system press the button. The parking lights will ash 1 time,

indicating the system is disarmed and has unlocked the doors (if equipped and

connected).

NOTE: The system is equipped with a feature called Silent Choice. If enabled, the

system requires a second press of the button to activate an audible disarming

response from the vehicle. If your system is set up for 2 step unlock, a third press of

unlock will activate the audible response.

*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more

than 2 seconds.

Using Your Remote Control

4caSECRS ca2LED5 4280831 Owners revB

Two Stage Door Unlock (Optional)

If this feature is enabled on your system, pressing the button one time will unlock

only the driver’s door. Press again within three seconds to unlock the remaining

doors.

Activating the Trunk Release Feature (Optional)

If this feature is enabled on your system, pressing and holding the button for 3

seconds will open the vehicle’s trunk or hatch.

Activating the AUX 1 Output (Optional)

If this feature is enabled on your system, pressing the and buttons

simultaneously will activate an optional feature. This feature can be programmed for a

wide range of functions like power window or sunroof automation, please consult your

installing dealer to determine the functionality of your system.

Entering AUX Mode and Activating the Additional AUX 2 - 5 Outputs (Optional)

To access the additional AUX outputs, AUX 2, AUX 3, AUX 4, and AUX 5, you must

rst enter the transmitters AUX Mode. This will “shift” the functions of the transmitter

buttons from their standard operation to control of the AUX outputs.

AUX Mode - 4 button transmitter: Press and Hold and for 2

seconds, the transmitter LED will ash 1 time. AUX Mode will remain active

for 15 seconds. AUX Mode will exit after 15 seconds of inactivity or by

pressing and again for 2 seconds, the transmitter LED will ash 2

times to conrm exit.

Using the Progressive Car Finder Feature

Press the button to locate your vehicle. The system will ash the parking lights

and sound 5 times at low volume, increasing in volume each time the button is

pressed.

Using the Personal Protection Alarm (Panic)

Press and hold the button for 3 seconds to activate the personal protection alarm.

During panic mode, the normal function of the transmitter buttons will be suspended.

The transmitter’s and buttons can be used to lock and unlock the door (if the

option is installed). To stop the alarm, press and hold the button on the transmitter

again for 3 seconds. The system will automatically stop after 30 seconds.

Programmed Transmitter Notication

As a security precaution each time the vehicle’s ignition is turn on the status LED

light with ash the number of transmitters programmed into the system. This helps

to identify unauthorized transmitters from accessing your vehicle. If you believe an

unauthorized transmitter has been programmed to your system, contact your installing

dealer for assistance.

Valet Mode

When valet mode is activated the status LED will light solid, and all security and

remote start functions will be disabled. To enter or exit valet mode simply follow the

steps outlined below:

1. Turn the vehicle’s ignition ON.

2. Push and hold the programming/valet button.

3. The LED will turn on solid when valet mode is active

4. Release the programming/valet button.

User Selectable Notication Chirps

System ARM/DISARM chirps can be toggled ON or OFF without entering the

programming feature banks.

1. Turn the ignition ON then OFF.

2. Press and release the valet/programming button 3 times. The system

will respond with 1 chirp for ON or 2 chirps for OFF.

6caSECRS ca2LED5 4280831 Owners revB

Carjack Mode (Anti-Hijack Mode)

This feature must be turned on in system programming, please consult your installing

dealer.

Triggering Carjack mode: While the ignition is ON and press and hold + for 2

seconds, the parking lights will ash 1 time and the system will act as follows;

1. 50 seconds after being triggered the siren will chirp for 15 seconds,

during this 15 seconds you will be alerted to push the valet button to

turn o󰀨 Carjack mode. If Carjack mode is not turned o󰀨 at this time it

will advance to the next step.

2. Following the 15 second chirps (total time now 65 seconds) the siren

will go into full sound and the parking lights will start ashing.

3. 90 seconds after trigger in, addition to the siren and parking lights, the

system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS

STATE UNTIL THE BATTERY IS DEPLETED.

OVERRIDE THE SYSTEM TO TURN OFF CARJACK MODE: Turn the ignition OFF

then On and press the valet button within 10 seconds.

Manually Overriding the Security System

Your system can be disarmed without the use of the transmitter. This is necessary,

since you will need the ability to operate your vehicle if the transmitter is lost or its

battery fails. To by-pass the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the ON position.

3. Within 10 seconds, press and release the valet push button switch.

The alarm system will stop sounding and enter the (by-passed) mode. You can now

start and operate the vehicle normally.

User Selectable LED

This feature will control whether the LED is ON or OFF when the system is Armed/

Locked and can be toggled ON or OFF without entering the programming feature

banks.

1. Turn the ignition ON, OFF, ON, OFF.

2. Press and release the valet/programming button 3 times. The system

will respond with 1 chirp for ON or 2 chirps for OFF.

Using Your Remote Starter

Remote Start Ready Mode - Manual Transmission Vehicles Only

To activate the remote start function, the system must rst be in Remote Start Ready

Mode. Follow the steps below to enter remote start ready mode.

1. While the engine is running by the ignition key;

a. Place the transmission in neutral.

b. Set the parking brake

2. With your foot o󰀨 the brake pedal, press and release the button to

activate the remote start. The LED will ash 3 times and the parking

lights will turn on to conrm the system has remote started.

3. Remove the keys from the ignition, the vehicle will remain running.

4. Exit the vehicle and close all vehicle doors.

5. Within 1 minute of step 1, press the button to lock the vehicle’s

doors. The vehicle will shutdown and sound 2 short chirps then 1 long

chirp to conrm ready mode is set.

Remote Start Ready Mode must be enabled if your vehicle is equipped with a

manual transmission.

Cancelling Remote Start Ready Mode - Manual Transmission Vehicles Only

The system will exit remote start ready mode if any of the following occur:

Open any door

Open the hood or trunk (if connected)

Press the brake

Release the parking brake

Turn the ignition ON

8caSECRS ca2LED5 4280831 Owners revB

Remote Starting Your Vehicle

To activate the remote start function, press and release the button 2 times within 2

seconds. The system will sound, the parking lights will ash 1 time and the system

will check the vehicle to ensure it is safe to start. If all safety parameters are correct,

the vehicle will start. The vehicle’s parking lights will turn on (or ash depending on

system settings) as a visual indication that the vehicle has started and is running.

If your vehicle stalls or does not start, the system will pause 5 seconds, then try

3 more times to start the vehicle (a total of 4 attempts). The system will pause 5

seconds between each start attempt.

Remote Start Shutdown

Press and hold the button for 3 seconds to turn the vehicle o󰀨.

Entering the Vehicle while it is Running via Remote Vehicle Start

1. Unlock the vehicle’s doors.

2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!

3. Insert the key into the ignition switch and turn to the ON or RUN

position.

4. Press the brake pedal. The remote vehicle starter will disengage and

the vehicle will operate normally.

To Enter & Exit the Vehicle while (Manual Transmission) Remote Start Ready

Mode is already active without cancelling Remote Start Ready Mode.

If ready mode has already been activated and you need to enter the vehicle, possibly

to retrieve an item, and will exit the vehicle without driving it, you can keep ready

mode active by following the steps below.

1. With Ready Mode already previously set, activate the remote start.

2. While under control of the remote start open vehicle door to retrieve

items.

3. Exit the vehicle and close all doors.

4. Press the button, the unit waits 3 seconds and then shuts down,

the system will verify all doors have been closed then will emit the 2

short/1 long tone and light ash pattern indicating Manual Transmission

Ready Mode is active.

Note: If the 2 short/1 long tone is not heard then Ready Mode has not been

set.

Using the “Quick-stop” Feature

If you want to make a short stop and keep your vehicle running (to keep the interior

warm or cool), the quick-stop feature allows you to do this while keeping your vehicle

secure and your keys with you.

To engage Quick Stop:

1. Stop the vehicle and place the transmission in PARK.

2. With your foot o󰀨 the brake pedal, press and release the button 2

times within 2 seconds. The LED will ash 3 times to conrm quick

stop is entered.

3. Remove the keys from the ignition and exit the vehicle. Press the

button to lock the vehicle’s doors if desired.

To engage Quick Stop - Manual Transmission Vehicles:

1. With the vehicle running, foot o󰀨 the brake, parking brake set ON.

2. Press and release the button to activate remote start.

3. Exit the vehicle close all doors (Door Open/All Doors Close)

4. Press and release the button.

5. Within 3 seconds press the button:

The unit enters Quick Stop Mode and will remain running

until remote start time-out and then shut down. (Remote Start Ready

Mode is NOT active)

Note: Do not leave children or animals unattended in the vehicle when using the

quick-stop feature.

10 caSECRS ca2LED5 4280831 Owners revB

User Programmable Run Time / Run Time Extension

The system has the ability to allow the user to extend the time the vehicle will be

running under control of the remote start. This will only extend the run time back to

the current run time setting during the current remote start cycle. If your system is

set to run 15 minutes and the time remaining is 4 minutes, extending the run time

will reset the countdown timer to 15 minutes and your vehicle will continue to run for

another 15 minutes. Follow the steps below to extend the vehicle’s run time.

1. The remote start must already be active.

2. Press and release the button 4 times.

3. The system will chirp 1 time and ash the parking lights 4 times to

conrm that the run time has been reset.

Turbo Timer

This option will keep the engine running to allow the vehicle’s turbo to properly cool

down before shutting the engine o󰀨.

To engage the Turbo Timer feature:

1. With the vehicle running via the ignition key and your foot o󰀨 of the

brake pedal.

2. Engage the vehicle’s parking brake and press the and

buttons simultaneously.

3. The vehicle’s parking lights will turn on to verify the Turbo Timer

feature has been activated.

4. Turn the ignition key OFF, the vehicle will continue to run until the pre-

programmed time has elapsed (1, 3, or 5 minutes)

To disengage the turbo timer feature, press the vehicle’s brake pedal.

Preheating or Precooling the Vehicle’s interior

Before exiting the vehicle, set the temperature controls to the desired setting and

operation. After the system starts the vehicle, the heater or air conditioner will

activate and heat or cool the vehicle’s interior to your setting.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Code Alarm Autozubehör Handbücher

Code Alarm

Code Alarm TKRS1 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung

Code Alarm ca2LED5E Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken